BioPACE

While developing the specifications for electronically enabled Machine Readable Travel Documents, the ICAO paid significant attention to security aspects related to the digital information stored in this type of electronic document. This has resulted in Passive and Active Authentication, Basic Access Control and Extended Access Control. The goal of Basic Access Control (BAC) is preventing unauthorized access to the chip data stored on eMRTDs. The PACE protocol has been developed as a future-proof method to overcome the limitations of BAC and to replace BAC in the future. In this paper the BioPACE protocol is proposed as a supplement to the PACE protocol. Besides verifying if the document holder is indeed the rightful owner, the BioPACE protocol provides a higher convenience for the bearer of the document.     

Solar water splitting with p-SiC film on p-Si: Photoelectrochemical behavior and XPS characterization

The electrochemical properties of single-crystalline p-type 3C-SiC films on p-Si substrate were investigated as an electrode in H₂SO₄ aqueous solutions in dark and under white light illumination. The photoelectrochemical (PEC) measurements indicates the p-type 3C-SiC film on p-Si substrate can generate a cathodic photocurrent as a photocathode, which corresponds to hydrogen production, and generate an anodic photocurrent as a photoanode, which corresponds to oxygen evolution. The surface chemical states of the films were investigated by XPS. In order to observe the surface chemical state changes after PEC test, the range of applied potential to the electrode was divided into three zones: −3.6 to 0 V, 0–1.5 V and 1.5–4 V vs. Ag/AgCl. After separated PEC tests in these three areas, XPS shows the surface of the SiC film in the range of −3.6 to 0 V and 0–1.5 V was stable without oxidation except the band bending occurred. But in the range of 1.5–4 V the film surface was oxidized due to anodic oxidation.     

Flammability of layered silicate epoxy nanocomposites combined with low‐melting inorganic ceepree glass

Tetraphenylphosphonium modified layered silicate epoxy nanocomposite (EP/TPPMMT) combined with low‐melting silicate glass, Ceepree (CP) is investigated by thermal analysis, flammability tests and cone calorimeter at different heat fluxes. Adding CP and TPPMMT does not change the pyrolysis apart from increasing inorganic residue. The total heat evolved (THE) is changed insignificantly, as neither relevant additional carbonaceous charring nor flame inhibition occurs. However, flame retardancy is clearly observed due to an inorganic‐carbonaceous surface protection layer. The peak heat released rate (PHRR) is reduced by around 32–42% when 5 wt% TPPMMT is added, and 51–63% when 10 wt% CP is added. PHRR reduction less than expected is observed when both additives are combined. The reduction is greater than that achieved by using TPPMMT but less than when only CP is used. The morphology of fire residue is investigated by scanning electron microscope on different length scales and turns out to be the key to understanding the efficiency of flame retardancy. The fire residue of EP/CP shows a layered structure, whereas separated columns limit the barrier properties for EP/5%TPPMMT on the micrometer scale. Columns dominating the fire residue structure of EP/5%TPPMMT/10%CP deteriorate the fire retardancy, whereas a more integral structure at the top of the residue causes the improvement over EP/5%TPPMMT. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers     

The influence of third-body particles on wear rate in unicondylar knee arthroplasty: a wear simulator study with bone and cement debris

The reduced intraoperative visibility of minimally invasive implanted unicondylar knee arthroplasty makes it difficult to remove bone and cement debris, which have been reported on the surface of damaged and retrieved bearings. Therefore, the aim of this study was to analyze the influence of bone and cement particles on the wear rate of unicompartmental knee prostheses in vitro. Fixed bearing unicompartmental knee prostheses were tested using a knee-wear-simulator according to the ISO standard 14243-1:2002(E) for 5.0 million cycles. Afterwards bone debris (particle size 671 ± 262 μm) were added to the test fluid in a concentration of 5 g/l for 1.5 million cycles, followed by 1.5 million cycles blended with cement debris (particle size 644 ± 186 μm) in the same concentration. Wear rate, knee-kinematics and wear-pattern were analyzed. The wear rate reached 12.5 ± 1.0 mm³/million cycles in the running-in and decreased during the steady state phase to 4.4 ± 0.91 mm³/million cycles. Bone particles resulted in a wear rate of 3.0 ± 1.27 mm³/million cycles with no influence on the wear rate compared to the steady state phase. Cement particles, however, lead to a significantly higher wear rate (25.0 ± 16.93 mm³/million cycles) compared to the steady state phase. The careful removal of extruded cement debris during implantation may help in reducing wear rate. Bone debris are suggested to have less critical influence on the prostheses wear rate.