Design and optimization of ceramic membrane structure: From the perspective of flux matching between support and membrane

The support flux was first investigated as a separate influencing factor for its effect on performances of ceramic filtration membranes. Three pre-membranes were prepared by tape-casting and then transfer-coated to supports to form dual-layer ceramic membranes after sintering. Experiments demonstrated that membrane layers with almost the same properties were obtained despite the huge difference in support flux. When the support flux increases from 3.120 to 97.53 m³m^?2h^?1, the flux of these three membrane series have increased by 75%, 186% and 228%, respectively. Experimental rules can provide structural design and evaluation from the perspective of permeability. The limit membrane flux of a certain system was derived according to the resistance distribution law of internal membrane structure and the Darcy's theorem. On this basis, a method for designing support flux was proposed. Furthermore, we present a criterion to quickly and easily evaluate the match between the support and the top layer, which is the ratio of membrane resistance to total resistance. Finally, the filtration resistance of penetration caused by suction of membrane particles into the support was measured for the first time, taking the advantage of the transfer-coating method that inherently free of penetration. Our works are expected to deepen the understanding of the ceramic membrane structure and provided guidance for its rational design and optimization.     

CFD Modeling of Active Volume Creation in a Non‐Newtonian Fluid Agitated by Submerged Recirculating Jets

Computational fluid dynamics (CFD) models were employed to investigate flow conditions inside a model reactor in which yield stress non‐Newtonian liquid is mobilized using submerged recirculating jets. The simulation results agree well with the experimental results of active volume in the reactor obtained using flow visualization by the authors in a previous study. The models developed are capable of predicting a critical jet velocity (v_c) that determines the extent of active volume obtained due to jet mixing. The v_c values are influenced both by the rheological properties of the liquid and the nozzle orientation. The liquid with higher effective viscosity leads to higher v_c for a downward facing injection nozzle. However, an upward facing injection nozzle along with a downward facing suction nozzle generates enhanced complementary flow fields which overcome the rheological constraints of the liquid and lead to lower v_c.     

Fulde–Ferrell State in Spin–Orbit-Coupled Superconductor: Application to Dresselhaus SOC

We show that in the presence of magnetic field, two superconducting phases with the center-of-mass momentum of Cooper pair parallel to the magnetic field are induced in Dresselhaus spin–orbit-coupled superconductor. Specifically, at small magnetic field, the center-of-mass momentum is induced due to the energy-spectrum distortion and no unpairing region with vanishing singlet correlation appears. We refer to this superconducting state as the drift-BCS state. By further increasing the magnetic field, the superconducting state falls into the Fulde–Ferrell state with the emergence of the unpairing regions. The observed abrupt enhancement of the center-of-mass momenta and suppression on the order parameters during the transition indicate the occurrence of a first-order phase transition. Enhanced Pauli limit and hence enlarged magnetic-field regime of the Fulde–Ferrell state, due to the spin-flip terms of the spin–orbit coupling, are revealed. We also address the triplet correlations induced by the spin–orbit coupling, and show that the Cooper-pair spin polarizations, generated by the magnetic field and center-of-mass momentum with the triplet correlations exhibit totally different magnetic-field dependences between the drift-BCS and Fulde–Ferrell states.     

Microwave dielectric properties of SrLa[Ga1−x(Mg0.5Ti0.5)x]O4 and SrLa[Ga1−x(Zn0.5Ti0.5)x]O4 (x = 0.2-0.8) ceramics

SrLa[Ga_1−x(R_0.5Ti_0.5)_x]O₄ (R = Mg, Zn) ceramics were prepared by a standard solid state sintering method. The single-phase ceramics with K₂NiF₄-type layered perovskite structure and I4/mmm space group were obtained, indicating that SrLa(R_0.5Ti_0.5) and SrLaGaO₄ can form the unlimited solid solutions. With increasing x for R = Mg and Zn, ε_r increases monotonously, the Qf value first increases and then decreases, while τ_f increases from a negative to a positive value. The optimized microwave dielectric properties were obtained as following: ε_r = 23.3, Qf = 89 400 GHz, τ_f = −0.8 ppm/°C for SrLa[Ga_0.6(Mg_0.5Ti_0.5)_0.4]O₄ and ε_r = 23.3, Qf = 76 200 GHz, τ_f = 0.2 ppm/°C for SrLa[Ga_0.7(Zn_0.5Ti_0.5)_0.3]O₄, indicating that the present solid solution ceramics are the promising candidates as microwave resonator materials for the telecommunication applications.     

Adaptive Finite-time Tracking Control for Class of Uncertain Nonlinearly Parameterized Systems with Input Delay

International Journal of Control, Automation and Systems - In this paper, the tracking problem for a class of uncertain nonlinearly parameterized systems with input delay based the adaptive...