软交换技术的发展及其应用

软交换是下一代网络NGN的核心技术，本文从软交换的概念入手，介绍了软交换的基本功能及其优点．软交换的网络系统结构、软交换的对外接口等内容，并探讨了软交换技术的应用。     

冲击噪声背景下的近场源二维参数估计方法

本文针对背景噪声为冲击噪声的情况,提出了一种新的近场源二维参数估计方法.本方法利用协变异(或协变异系数)构造矩阵,并通过求根的方法估计近场源的方向角和距离参数.该算法可以抑制冲击噪声对估计性能的影响,同时具有无需谱峰搜索的优点.仿真实验证明了该算法的有效性.     

蓝牙技术在某型飞机机载火控故障诊断系统中的应用研究

蓝牙技术是一种短距离无线通信技术,具有低成本、低功耗、灵活、快速、抗干扰能力强等特点,目的是取代终端的连接电缆.为提高部队的作战效能,采用蓝牙技术和计算机测量与控制技术,研制了机载火控故障诊断系统;该系统在实际应用中取得了良好效果,并具有诊断结果准确、自动化程度高、工作稳定可靠、操作简便、易于转移和维护等优点,为技术人员进行机载火控系统的性能检测与故障诊断提供了便利.     

Reverse short channel effects in high-k gated nMOSFETs

Anomalous threshold voltage roll-up behavior, commonly referred as reverse short channel effect (RSCE), has been observed in high-k (HfO₂ on SiON buffer, Al₂O₃ on SiON buffer) gated submicron nMOSFETs, while the SiO₂ or SiON control samples show normal short channel effect (SCE) behavior. The possible causes such as inhomogeneous channel doping profile and gate oxide thickness variation near S/D ends have been ruled out. The results indicate that interface trap density that dependents on channel length is the main cause of the RSCE observed here. In addition, oxide charge also plays a role.     

Grazing incidence reflection absorption Fourier transform infrared (GIRA-FTIR) spectroscopic studies on the ferroelectric behavior of poly(vinylidene fluoride–trifluoroethylene) ultrathin films

Grazing incidence reflection absorption Fourier transform infrared (GIRA-FTIR) spectroscopy was used to characterize the ferroelectric behavior of a thin poly(vinylidene fluoride–trifluoroethylene) P(VDF–TrFE) copolymer. The lab-built GIRA-FTIR apparatus allowed the heating and corona poling process to be carried out whilst collecting the GIRA spectra of the thin polymer film. The Curie transition from the ferroelectric to paraelectric phase was confirmed from the abrupt change in intensity of the 849 cm⁻¹ band in the RA-FTIR spectrum. It was found that the Curie temperature dropped dramatically when the film thickness was lowered to below a certain critical value of approximately 100 nm. The switching of the CF₂ dipoles in the ferroelectric crystals after applying the external electric field could be determined by monitoring the change in the 849 cm⁻¹ band intensity. For the 600 nm thick P(VDF–TrFE) film, the switching of the dipoles appears to occur almost instantaneously, while the kinetics of dipole switching of the 75 nm thick film were significantly retarded. The repeated switchability of the CF₂ dipoles upon the application of a bipolar cyclic electric field was also confirmed. The bistability of the film due to remnant polarization was also confirmed from the absorbance of the 849 cm⁻¹ band after removing the applied voltage during corona poling.     

A new distributed approximation algorithm for constructing minimum connected dominating set in wireless ad hoc networks

In recent years, constructing a virtual backbone by nodes in a connected dominating set (CDS) has been proposed to improve the performance of ad hoc wireless networks. In general, a dominating set satisfies that every vertex in the graph is either in the set or adjacent to a vertex in the set. A CDS is a dominating set that also induces a connected sub‐graph. However, finding the minimum connected dominating set (MCDS) is a well‐known NP‐hard problem in graph theory. Approximation algorithms for MCDS have been proposed in the literature. Most of these algorithms suffer from a poor approximation ratio, and from high time complexity and message complexity. In this paper, we present a new distributed approximation algorithm that constructs a MCDS for wireless ad hoc networks based on a maximal independent set (MIS). Our algorithm, which is fully localized, has a constant approximation ratio, and O(n) time and O(n) message complexity. In this algorithm, each node only requires the knowledge of its one‐hop neighbours and there is only one shortest path connecting two dominators that are at most three hops away. We not only give theoretical performance analysis for our algorithm, but also conduct extensive simulation to compare our algorithm with other algorithms in the literature. Simulation results and theoretical analysis show that our algorithm has better efficiency and performance than others. Copyright © 2005 John Wiley & Sons, Ltd.     

3Cr-3Mo二次硬化钢的回火组织和力学性能

研究了3cr—3Mo二次硬化钢淬火回火后的组织和力学性能。结果表明：随回火温度的升高，试验钢中先后析出M3c、M2c和M7C3等碳化物，在575℃回火时硬度达到峰值；400一575℃回火后试验钢的抗拉强度约为l600MPa，冲击韧性为30J／cm^2；回火温度高于600℃时，强度和硬度迅速下降，冲击韧性增加；640℃回火时，以M2C型碳化物为主，抗拉强度为1100MPa，冲击韧性增加至55J／cm^2。     

Effects of surfactant/silica and silica/cerium ratios on the characteristics of mesoporous Ce-MCM-41

Using the surfactant CTMABr (cetyltrimethyl ammonium bromide) and cerium(IV) sulfate, mesoporous Ce-MCM-41 molecular sieves were produced under a hydrothermal condition with various surfactant/silica (surfactant/Si) and silica/cerium (Si/Ce) ratios. Changes to the structural traits caused by changing the molar ratios of both surfactant/Si and Si/Ce were investigated. XRD (X-ray diffraction), FT-IR (fourier transform infrared spectroscopy), and SEM (scanning electro microscopy) were used for the characterization of prepared mesoporous samples. Among the tested molar ratios, surfactant/Si ratio of 0.5 and 0.2 showed highest values of d_1 0 0 and intensity, respectively, for the Si-MCM-41. XRD analysis also identified a quintessential hexagonal structure of Ce-MCM-41 for the Si/Ce molar ratio higher than 40 (maintaining the surfactant/Si ratio at 0.2). When cerium content was increased to have the Si/Ce molar ratio of 20, the hexagonal structure of Ce-MCM-41 was collapsed due to the structural stress of substituted cerium. FT-IR results confirmed calcination of Ce-MCM-41 and the incorporation of Ce⁴⁺ ions of cerium sulfate into the silica surface with proper removal of the surfactant. Rod-like shape with rounded edges of the prepared Ce-MCM-41 samples was identified by SEM. These results suggest surfactant/Si ratio of 0.2 and Si/Ce ratio of 40 for the production of Ce-MCM-41 with the highest level of crystallinity.     

市区微蜂窝传播路径损耗模式的比较检验

讨论了几种微蜂窝路径损耗模式,并用我国某城市测量的微蜂窝传播数据对COST231WI,修正COST231WI和Xia模式进行了检验,结果表明修正COST231模式的误差最小,Xia模式次之,COST231WI模式最差。从而得到修正COST231模式比较符合我国实际的微蜂窝传播预测模式。     

逆向工程技术在机械领域的应用

逆向工程技术已成为联系新产品开发过程中各种先进技术的纽带,并成为实现新产品快速开发的重要技术手段.介绍了逆向工程的概念、技术流程、测量系统、常用软件以及实际应用.