Sparse decompositions for exploratory pattern analysis

We define and verify the utility of a pattern analysis procedure called sparse decomposition. This technique involves sequentially ``peeling' sparse subsets of patterns from a pattern set, where sparse subsets are sets of patterns which possess a certain degree of regularity or compactness as measured by a compactness measure c. If this is repeated until all patterns are deleted, then the sequence of decomposition ``layers' derived by this procedure provides a wealth of information from which inferences about the original pattern set may be made. A statistic P is derived from this information and is shown to be powerful in detecting clustering tendency for data in reasonably compact sampling windows. The test is applied to both synthetic and real data.     

Parallel 2-d convolution on a mesh connected array processor

In this correspondence, a parallel 2-D convolution scheme is presented. The processing structure is a mesh connected array processor consisting of the same number of simple processing elements as the number of pixels in the image. For most windows considered, the number of computation steps required is the same as that of the coefficients of a convolution window. The proposed scheme can be easily extended to convolution windows of arbitrary size and shape. The basic idea of the proposed scheme is to apply the 1-D systolic concept to 2-D convolution on a mesh structure. The computation is carried out along a path called a convolution path in a systolic manner. The efficiency of the scheme is analyzed for windows of various shapes. The ideal convolution path is a Hamiltonian path ending at the center of the window, the length of which is equal to the number of window coefficients. The simple architecture and control strategy make the proposed scheme suitable for VLSI implementation.     

Tests in an MR reactor of experimental fuel elements of the VVÉR-1000 reactor

Conclusions In an MR reactor performance tests of 16 fuel assemblies, with elements having essentially the same structure as standard VVÉR-100 fuel elements, were carried out. Tests of five more fuel assemblies are continuing. Of the 16 assemblies, 13 were studied in a hot laboratory.The tests in the MR, carried out at high loads and with a large number of transition processes, as well as the postreactor studies, indicated that fuel elements of the specified design (with initial helium pressures of 1.96–2.45 MPa) have a high reliability. None of the elements of the fuel assemblies studied malfunctioned due to design defects or faults in their fabrication. During the tests the jackets were subject to a little oxidation and hydrogenation (zirconium-oxide film<3 m thick, hydrogen content less than 0.008% by mass), and their plasticity remained high (the relative elongation at the working temperature remained at the 20% level).Translated from Atomnaya Énergiya, Vol. 62, No. 5, pp. 312–317, May, 1987.     

Tri-Reforming of Methane over NdM0.25Ni0.75O3 (M = Cr,Fe) Catalysts and the Effect of CO2 Composition

Catalysis Letters - The NdM0.25Ni0.75O3 (M?=?Cr, Fe) named NCN and NFN catalysts precursors were synthesized and characterized. The CO2 utilization in the feed was studied in the...     

AN EXPERIMENTAL-NUMERICAL METHOD FOR MEASURING CRACK PROPAGATING VELOCITIES UNDER STRESS WAVE LOADING

An experimental-numerical method for measuring dynamic crack propagating velocities under stress wave loading is established in this paper. The experiments of the three-point bend specimen are done on the improved Hopkinson bar. Deflection of loading point, dynamic load and instantaneous crack length are measured, then crack propagating velocities are calculated. Experiments on 40Cr steel show that the results given by this method have a good agreement with that obtained by the resistance fracture gage method. Therefore this method is feasible for measuring crack propagating velocities under high loading rate and will have wide application.     

The generation of surface roughness during slurry erosion-corrosion and its effect on the pitting potential

Results of experiments performed to isolate the effect of surface roughness generated during slurry erosion-corrosion of 304L stainless steel are presented. Surfaces prepared by grinding to different finishes show that increasing the roughness lowers the pitting potential in chloride solution. Subsequent erosion by an aqueous sand slurry then alters this pitting potential (E_p), as measured in the solution phase alone, in a manner dependent on the initial surface roughness. Surfaces which were initially rougher show a pronounced rise in _p after erosion, while those with an initially smoother finish show a fall in E_p after erosion. Measurement of E_p during erosion-corrosion does not fit either process, with values of _Ep lower than those predicted from the surface roughness alone.     

Development of Cr and Al Pack Cementation Coatings on Co-Based γ/γ′ Superalloys

Metallurgical and Materials Transactions A - Co-based superalloys have been developed as candidate materials to replace Ni-based superalloys in hot sections of turbine engines, however, their...     

Processing a Sn–Pb Alloy to Produce Tin

Russian Journal of Non-Ferrous Metals - The aim of the work is to develop an optimal method for processing Sn–Pb alloy to obtain a marketable product-branded O1?O3 tin (Sn ≥...