High-resolution photonics-based interference suppression filter with wide passband

A new topology for a photonic signal processor, which overcomes the basic recursive frequency response problem that limits the passband range, is presented. The structure is based on a new multiple-wavelength offset-cavity structure that is cascaded with a series of unbalanced delay line structures. This not only can synthesize a very narrow notch response with good shape factor but also permits a multifold extension of the free spectral range (FSR) and passband width. Results on the interference mitigation filter demonstrate a stopband of 1% of center frequency and a fourfold increase in the FSR and passband width, while also having a very small shape factor, in excellent agreement with predictions.     

Low Temperature Physics at the Laboratoire National des Champs Magnétiques Pulsés in Toulouse

An overview over past and present activities and future developments at the Toulouse pulsed magnetic field facility is given, both as far as technical developments of the infrastructure, as well as low temperature physics performed at the LNCMP are concerned.     

Volumetric Change and Surface Properties of Temperature-Sensitive Polyvinylalcohol (PVA) Hydrogel

Polyvinylalcohol (PVA) polymer gel is a temperature sensitive polymeric gel, with a critical transition temperature (with H₂O) of 310 K. At higher than 310 K, this temperature sensitive polymer gel shrinks because of discharging water, whereas at lower temperatures, the gel swelled because of absorbing water. The reversibility of the gel's volume change was confirmed by temperature swing. The adsorption behavior of an organic compound onto the PVA polymer gel in water was tested at various temperatures. The amount of adsorbed organic compound increased remarkably at temperatures higher than about 310 K. Then, it was confirmed that the organic compound in PVA polymer gel could be reversibly adsorbed and desorbed by a temperature change between 293 and 323 K. The mechanism of adsorption of the organic compound onto the PVA polymer gel could be explained by hydration and dehydration of polymer gel.     

Classification of audio radar signals using radial basis function neural networks

Radial basis function (RBF) neural networks are used to classify real-life audio radar signals that are collected by a ground surveillance radar mounted on a tank. Currently, a human operator is required to operate the radar system to discern among signals bouncing off tanks, vehicles, planes, and so on. The objective of this project is to investigate the possibility of using a neural network to perform this target recognition task, with the aim of reducing the number of personnel required in a tank. Different signal classification methods in the neural net literature are considered. The first method employs a linear autoregressive (AR) model to extract linear features of the audio data, and then perform classification on these features, i.e, the AR coefficients. AR coefficient estimations based on least squares and higher order statistics are considered in this study. The second approach uses nonlinear predictors to model the audio data and then classifies the signals according to the prediction errors. The real-life audio radar data set used here was collected by an AN/PPS-15 ground surveillance radar and consists of 13 different target classes, which include men marching, a man walking, airplanes, a man crawling, and boats, etc. It is found that each classification method has some classes which are difficult to classify. Overall, the AR feature extraction approach is most effective and has a correct classification rate of 88% for the training data and 67% for data not used for training.     

Mechanical spectroscopy in commercial Fe–6 wt.% Si alloys between 400 and 1000 K

Mechanical spectroscopy, neutron diffraction and differential scanning calorimetry (DSC) were performed on commercial Fe–6 wt.% Si alloy after quenching from high temperature. The damping spectrum shows a peak at around 800 K and an associated modulus defect. The modulus shows an increase during the second and subsequent heating runs. In addition, an anomaly in the modulus behavior has been found at around 400 K. Different thermal treatments allows to obtain two different recovery degrees of the quenched-in defects. The influence of the recovery degree on the 800 K internal friction peak and on the anelastic modulus has been evaluated and confirm the validity of the grain boundary mechanism associated to this peak. Experimental results are discussed on the basis of recovery and ordering processes.     

Modification of ASM3 for the determination of biomass adsorption/storage capacity in bulking sludge control.

The selector activated sludge (SAS) systems are known to prevent excessive growth of filamentous microorganisms responsible for bulking sludge, but these systems were hardly ever modelled. This study aimed to develop a model capable of predicting rapid substrate removal in the SAS systems. For this purpose, the Activated Sludge Model No. 3 (ASM3) was extended with three processes (adsorption, direct growth on the adsorbed substrate under aerobic or anoxic conditions). The modified ASM3 was tested against the results of batch experiments with the biomass originating from two full-scale SAS systems in Germany. The endogenous biomass was mixed with various readily biodegradable substrates (acetate, peptone, glucose and wastewater) and the utilisation of substrate (expresses as COD) and oxygen uptake rates (OURs) were measured during the experiments. In general, model predictions fitted to the experimental data, but a considerable number of kinetic (5) and stoichiometric (2) parameters needed to be adjusted during model calibration. The simulation results revealed that storage was generally a dominating process compared to direct growth in terms of the adsorbed substrate utilisation. The contribution of storage ranged from 65-71% (Plant A) and 69-92% (Plant B).     

Extractive Properties of Synergistic Mixtures of Dipicolinic Acid Diamides and Chlorinated Cobalt Dicarbollide

Extraction of Cs, Sr, Eu, U, Np, and Am with mixtures of dipicolinic acid diamides with chlorinated cobalt dicarbollide was studied. A synergistic effect was revealed.     

An Acoustic Converter Used to Measure Ionizing Radiation Energy Loss

A monitor is proposed based on ultrasonic production when ionizing radiation passes through a medium. The recording element is a 0.2 mm aluminum plate mounted in a ceramic acoustic converter AC in the form of a wedge of thickness 2 mm. The low plate thickness minimizes the beam parameter distortion, while special technology used in the AC provides high sensitivity. The device has been calibrated in the proton beam from the ITEP accelerator at 200 MeV with 2·10⁹–6·10¹⁰ particles in a pulse and a pulse length of 70 nsec.