Improvement in stabilization of launching performance and launching velocity using linear accelerator

This paper describes the improvements in launching stability and launching velocity of the linear accelerator (LAC). The authors have designed and produced a railgun using the LAC for weaving loom shuttles. The LAC is an electromagnetic launcher which enables a projectile to be launched at a speed of more than 50 m/s. Basically, it consists of a unipole linear dc motor and operates the same principle as dc rotary motors, the most difficult problem in this system being the stabilization of the current collection on the projectile. Then, various launch experiments have been conducted. As a result, the carbon projectile was launched at a speed of 73 m/s using double-state-type LAC.     

Utilization of LNG coldUtilisation du froid du GNL

This paper will discuss the utilization of LNG cold in Japan. Discussion is concentrated on the following: temperature conditions of both direct and indirect utilization; restriction in quantity and mode of cryogenic energy utilization; distance from LNG terminals to cold utilization plants; cooling system for LNG cold utilization plants, and emergence of cryogenic energy utilization complexes.     

Roles of low field mobility and its carrier-concentrationdependences in high electron mobility transistors and other field effecttransistors

A model is proposed for high-electron-mobility transistors (HEMTs) and other heterostructure FETs in which the dependence of low field mobility μ on carrier concentration N_s is taken into account. On the basis of this model, the influence of μ and its N_s dependence on drain current and transconductance g_m are clarified, In particular, high mobility (>10⁵ cm²/V-s) is shown to be effective in achieving and maintaining the intrinsic limit of g_m(=ε₂ν_s/d*) irrespective of bias conditions, where ν_s is the saturation velocity and ε₂ and d* are the dielectric permittivity and the effective thickness of the gate insulator, respectively. The N_s dependence of mobility is found to greatly affect the gate-voltage dependence of g _m and leads, in some cases, to an appreciable increase of g_m above its intrinsic limit     

Parameter estimation of radiocardiogram using a minicomputer

Radiocardiography has been widely used as a method for the quantification of cardiac output by applying the principle of the dye dilution method. This paper deals with an automatic analyzing system of radiocardiograms and a parameter estimation procedure using a linear system made up of four compartments with two time delays as a model of transport process in the blood circulatory system. The parameter estimation procedure named the window method in frequency domain is very effective for shortening the computing time and can be easily performed using a minicomputer. Parameter sensitivity analysis is also applied to study behavior of parameters on the model. Some analyzed results of radiocardiograms are shown and it is verified that the procedure is sufficiently useful and efficient for routine clinical use.     

Influence of microwave roasting on positional distribution of fatty acids of triacylglycerols and phospholipids in sunflower seeds (Helianthus annuus L.)

Whole sunflower seeds were exposed to microwave roasting for 6, 12, 20 or 30 min at a frequency of 2450 MHz. The kernels were then separated from the sunflower seeds, and the lipid components and the positional distribution of fatty acids in triacylglycerols (TAGs) and phospholipids (PLs) were investigated. Major lipid components were TAGs and PLs, while steryl esters, free fatty acids and diacylglycerols were also present in minor proportions. The greatest PL losses (p < 0.05) were observed in phosphatidyl ethanolamine, followed by phosphatidyl choline or phosphatidyl inositol. Significant differences (p < 0.05) in fatty acid distributions occurred (with few exceptions) when sunflower seeds were microwaved for 20 min or more. Nevertheless, the principal characteristics for the positional distribution of fatty acids still remained after 20 min of microwave roasting; unsaturated fatty acids, especially linoleic, were predominantly concentrated in the sn‐2‐position and saturated fatty acids, especially stearic and palmitic acids, primarily occupied the sn‐1‐ or sn‐3‐position. These results indicate that no significant changes in fatty acid distribution of TAGs and PLs would occur within 12 min of microwave roasting, ensuring that a good‐quality product would be attained.     

High-precision temperature control and stabilization using a cryocooler

We describe a method for precisely controlling temperature using a Gifford-McMahon (GM) cryocooler that involves inserting fiber-reinforced-plastic dampers into a conventional cryosystem. Temperature fluctuations in a GM cryocooler without a large heat bath or a stainless-steel damper at 4.2 K are typically of the order of 200 mK. It is particularly difficult to control the temperature of a GM cryocooler at low temperatures. The fiber-reinforced-plastic dampers enabled us to dramatically reduce temperature fluctuations at low temperatures. A standard deviation of the temperature fluctuations of 0.21 mK could be achieved when the temperature was controlled at 4.200?0 K using a feedback temperature control system with two heaters. Adding the dampers increased the minimum achievable temperature from 3.2 to 3.3 K. Precise temperature control between 4.200?0 and 300.000 K was attained using the GM cryocooler, and the standard deviation of the temperature fluctuations was less than 1.2 mK even at 300 K. This technique makes it possible to control and stabilize the temperature using a GM cryocooler.     

Magnetic resonance imaging and pathologic studies on lateral fluid percussion injury as a model of focal brain injury in rats

In this study, morphologic changes in brain lesions initiated by moderate lateral fluid percussion injury in rats were investigated chronologically using high-resolution magnetic resonance imaging (MRI) and histopathologic methods. Rats were subjected to moderate fluid percussion injury (average 2.80 +/- 0.48 atmospheres) over the exposed dura overlying the right parietal cortex. MRI obtained in vivo were compared with corresponding pathologic findings at 1, 6, and 24 h and at 3, 6, 14 and 80 days after injury. T2-weighted images showed scattered low-signal intensity in the injured cortex within a few hours after injury, whereas histologic findings revealed intraparenchymal hemorrhages. T2-weighted images of the ipsilateral cerebral cortex and/or corpus callosum showed a high-signal-intensity area 4 h after injury. The high-signal-intensity area became largest in size between 6 and 24 h, then declined gradually, and almost disappeared 14 days after injury. Histologic examination revealed pyknosis, retraction of the cell body of neurons with vacuolated neuropil in the corresponding regions 6 and 24 h after injury, and cystic necrosis 14 days after injury. The location and extent of these pathologic changes were depicted accurately by MRI in vivo. In the hippocampus, pyknosis and retraction of the cell body of pyramidal neurons were observed on the injured side 24 h after injury, and the number of neurons in the CA1 and CA2-CA3 regions decreased significantly on the same side by 14 days after injury. It is concluded that morphologic changes in the brain following experimental traumatic brain injury in rats are detectable in vivo by high-resolution MRI, and that MRI may be useful for the evaluation of treatment effects in experimental brain injury.     

Deformation behavior of polytetrafluoroethylene films under tensile stress at various temperatures

Deformation behavior of polytetrafluoroethylene (PTFE) films was investigated by thermomechanical analysis (TMA) under various tensile stresses (σ) up to 1.15 MPa in the temperature range from room temperature to 360°C. In the heating process above σ ≈ 0.25 MPa, a contraction of the PTFE film occurs in the melting temperature region. In the cooling process above σ ≈ 0.05 MPa, an elongation occurs in the crystallization temperature region, and above σ ≈ 0.5 MPa, it reaches 20–30% of the original length of the film. The PTFE films in the melt state above σ ≈ 0.5 MPa contract with increasing temperature up to 360°C and elongate with decreasing temperature. For the films that underwent deformation in the TMA, the crystalline orientation and the surface morphology were investigated by wide-angle X-ray diffraction and scanning electron microscopy, respectively. The degree of crystalline orientation in the deformed films increases with increasing σ and approaches a plateau at σ ≈ 0.4 MPa. On the surface of the deformed films, alignment of the bands and deformation of granules, which are formed by heat treatment above the melting point, are observed. © 1994 John Wiley & Sons, Inc.