医用聚氯乙烯材料的表面光接枝改性

研究了在不排氧氛围下 ,紫外光照射 ,以二苯甲酮 (BP)为光引发剂 ,甲基丙烯酸缩水甘油酯(GMA)在医用聚氯乙烯 (PVC)薄膜表面的气相接枝聚合。探讨了反应条件对接枝结果的影响 ,并用正交法指出了影响因素的显著性。用傅立叶红外 (FT- IR)、水接触角作为接枝改性结果的表征。FT- IR谱图表明 GMA已接枝到 PVC膜表面。水接触角由接枝前的 78°下降到 5 4°     

发电设备的检修策略及可靠性管理研究

检修策略和可靠性管理是发电厂设备管理工作相辅相成的 2个方面 ,必须予以足够重视。目前要加大力度做好可靠性管理工作 ,建立可靠性管理系统为发电设备管理提供技术支持 ,为设备检修提供依据 ,以获得最佳的经济效益。     

甲基丙烯酸乙酯合成工艺研究

以大孔强酸性离子交换树脂为催化剂,甲基丙烯酸(MAA)与乙醇直接酯化合成甲基丙烯酸乙酯(EMA)。在MAA与乙醇摩尔比为1:3、反应温度89～93℃、空速0.3h~(-1)的条件下,MAA转化率不低于98％,EMA的选择性不低于99％。     

In-situ composite Cu-Cr contact cables with high strength and high conductivity

In order to develop a new type of contact cable with high strength and high electrical conductivity, Cu-Cr alloy series were selected as materials and Cu-Cr alloy castings were produced by means of directional solidification continuous casting (DSCC) process. The results show that the fibrillar strengthening phase, 13-Cr, orderly arranges among the copper matrix phase along the wire direction; and a microstructure of in-situ composite forms, which retains the basic property of good conductivity of the copper matrix and meanwhile obtains the strengthening effect of [3-Cr phase. The production technology as well as the mechanical property, electrical property, and synthetic property of the in-situ composite contact cables was discussed.     

粉末冶金法制备PSZ/Mo复合材料的研究

本文采用粉末冶金法制备了不同成分的PSZ/Mo复合材料。并对其密度、弹性模量和热膨胀系数进行了测量和分析 ,用XRD进行了物相分析。实验结果表明 :纳米氧化锆的烧结性能比金属钼好 ;弹性模量估算选用简单混合法则进行计算时应进行修正 ;钼和氧化锆在烧结时不发生化学反应。通过热压PSZ/Mo功能梯度材料的断口扫描分析发现 :虽然金属钼和纳米氧化锆具有一定增韧作用 ,但材料断裂方式仍以脆性断裂为主     

On the interior resonance problem when applying a hybrid FEM/MoMapproach to model printed circuit boards

A hybrid finite element method/method of moments (FEM/MoM) technique is used to analyze a printed circuit board power bus structure where the source and observation points are in the near field. The FEM is used to model the lossy region between the planes of the board including the source. The MoM is used to model the region outside the planes and provide a radiation boundary condition to terminate the FEM mesh. Numerical results for a bridged power bus structure are compared with measurements. A nonphysical interior resonance of the electric field integral equation is observed. The problem can be avoided by using a hybrid technique based on a combined field integral equation     

烯烃聚合单活性中心非茂催化剂的最新研究进展

综述了近几年来烯烃聚合用单活性中心非茂催化剂的研究进展。简要介绍了 2 3种由前、后过渡金属组成的配位化合物催化剂的结构与性能     

炉衬产生的氧对真空钢液脱氮的动力学影响

采用 99.99%氧化镁砂捣打炉衬的 2 0kg真空感应炉 ,研究了超低碳钢熔炼时炉衬产生的氧对真空钢液脱氮的影响。试验结果表明 :钢液中氧含量在 1 2 0× 1 0 - 6 时 ,脱氮的限制性环节是界面化学反应 ;随炉衬中氧的逸出 ,当钢液中氧含量在 5 1 0×1 0 - 6 时 ,真空钢液脱氮处于界面化学反应和液相边界层扩散控制的边缘区域 ,脱氮速率降低     

票据使用与结算改革的构想

以票据为主体的结算制度，是我国结算改革的重大突破，也是结算改革取得显著成绩的表现。根据票据的特征，对票据使用在我国的可能性和必要性进行分析，并结合我国结算改革中存在的一些问题，提出几点设想。     

In-Situ observation on microfracture behavior ahead of the crack tip in 63Sn37Pb solder alloy

in-situ transmission electron microscopy (TEM) tensile tests on as-cast and aged 63Sn37Pb solder alloys were conducted, and the fracture behavior in nanometer scale ahead of the crack tip was inspected and discussed. Results show that the fracture was completed by connecting the discontinuous cracks or voids. Dislocation behavior was concentrated along the grain boundaries for as-cast samples, and displayed mainly as dislocation climb. The crack was intergranular dominated under the lower strain rate. While remarkable mutual dislocation emission was detected in the aged solder. Transgranular cracks were dominant in the fractured area, and they propagated by linking up with the nanometer scale cracks ahead of the crack tips under the effective promotion of the inverse dislocation emission. At the same time, the partial interphase or intergranular cracks in the thinned area were also found. Under this condition, a new critical stress intensity factor K _c ^′ to define the mutual dislocation emission was proposed.