Magnetron-sputtered cobalt-based protective coatings on ferritic steels for solid oxide fuel cell interconnect applications

Co, Co–Mn (67:33 at.%) and Co–Cu (67:33 at.%) coatings were fabricated using magnetron sputtering on two kinds of ferritic stainless steels (Crofer22APU and F17TNb) in order to form spinel protective coatings on metallic interconnects for solid oxide fuel cells. Despite the thickness unevenness at different regions, dense metallic coatings were successfully applied onto all necessary surfaces of the channelled interconnect substrates. Upon oxidation, spinel oxide coatings with very low Cr content were formed, reducing effectively the Cr release. Among the three protective coatings, Co–Cu coating showed the lowest area specific resistance (<15 mΩ cm² at 800 °C).     

基于实测数据的车轨耦合模型更新方法

提出了一种适用于车轨耦合系统的模型更新方法,其更新过程主要由两大步骤来实现:a.更新列车运行速度;b.更新扣件刚度。首先,建立了地铁列车车轨耦合系统模型,采用迭代的方法求解系统动力响应;其次,选取地铁普通整体道床轨道线路开展测试以获得现场实测数据,随后利用车轨耦合系统模型发现钢轨位移动力响应受扣件刚度影响较为明显,而受扣件阻尼影响较小。更新列车运行速度的主要目的是使激振主频更加吻合现场实测状况,在此基础上更新扣件刚度可使频域幅值更为接近。钢轨位移动力响应的频谱由列车周期荷载的一阶多次频率控制,这是由于轨道结构的多点连续支承特性所造成的。通过对比模型更新后的模拟结果与测试结果,验证了所提模型更新方法的可行性。研究结果表明,更新列车运行速度及扣件刚度是进行地铁列车与轨道耦合系统模型更新的有效方法之一。     

Preparation of scratch resistant superhydrophobic hybrid coatings by sol–gel process

Organic–inorganic hybrid coatings on glass substrates with superhydrophobic properties and with improved scratch resistance were obtained by means of applying a multilayer approach including multiple sol–gel processes. The coatings exhibited a water contact angle (WCA) higher than 150°. Ultraviolet (UV)-curable vinyl ester resins and vinyltriethoxysilane (VTEOS) as coupling agent were employed to increase the adhesion between substrate and the inorganic layers. The surfaces were characterized by means of dynamic contact angle and roughness measurements. Indeed, the occurrence of superhydrophobic behavior was observed. The scratch resistance of the hybrid coatings was tested to evaluate the adhesion of the coatings to the glass substrate. The proposed preparation method for scratch resistant, mechanically stable, superhydrophobic coatings is simple and can be applied on large areas of different kinds of substrates.     

Impact of neurite alignment on organelle motion

Intracellular transport is pivotal for cell growth and survival. Malfunctions in this process have been associated with devastating neurodegenerative diseases, highlighting the need for a deeper understanding of the mechanisms involved. Here, we use an experimental methodology that leads neurites of differentiated PC12 cells into either one of two configurations: a one-dimensional configuration, where the neurites align along lines, or a two-dimensional configuration, where the neurites adopt a random orientation and shape on a flat substrate. We subsequently monitored the motion of functional organelles, the lysosomes, inside the neurites. Implementing a time-resolved analysis of the mean-squared displacement, we quantitatively characterized distinct motion modes of the lysosomes. Our results indicate that neurite alignment gives rise to faster diffusive and super-diffusive lysosomal motion than the situation in which the neurites are randomly oriented. After inducing lysosome swelling through an osmotic challenge by sucrose, we confirmed the predicted slowdown in diffusive mobility. Surprisingly, we found that the swelling-induced mobility change affected each of the (sub-/super-)diffusive motion modes differently and depended on the alignment configuration of the neurites. Our findings imply that intracellular transport is significantly and robustly dependent on cell morphology, which might in part be controlled by the extracellular matrix.     

Mining the Wheat Grain Proteome

Bread wheat is the most widely cultivated crop worldwide, used in the production of food products and a feed source for animals. Selection tools that can be applied early in the breeding cycle are needed to accelerate genetic gain for increased wheat production while maintaining or improving grain quality if demand from human population growth is to be fulfilled. Proteomics screening assays of wheat flour can assist breeders to select the best performing breeding lines and discard the worst lines. In this study, we optimised a robust LC–MS shotgun quantitative proteomics method to screen thousands of wheat genotypes. Using 6 cultivars and 4 replicates, we tested 3 resuspension ratios (50, 25, and 17 µL/mg), 2 extraction buffers (with urea or guanidine-hydrochloride), 3 sets of proteases (chymotrypsin, Glu-C, and trypsin/Lys-C), and multiple LC settings. Protein identifications by LC–MS/MS were used to select the best parameters. A total 8738 wheat proteins were identified. The best method was validated on an independent set of 96 cultivars and peptides quantities were normalised using sample weights, an internal standard, and quality controls. Data mining tools found particularly useful to explore the flour proteome are presented (UniProt Retrieve/ID mapping tool, KEGG, AgriGO, REVIGO, and Pathway Tools).     

Growth and exopolysaccharide yield of Lactobacillus delbrueckii ssp. bulgaricus DSM 20081 in batch and continuous bioreactor experiments at constant pH

Some Lactobacillus delbrueckii ssp. bulgaricus strains are able to synthesize exopolysaccharides (EPS) and are therefore highly important for the dairy industry as starter cultures. The aim of this study was to investigate the nutritional requirements for growth and EPS production of Lactobacillus delbrueckii ssp. bulgaricus DSM 20081. A medium was developed from a semi-defined medium (SDM) in which glucose was replaced by lactose and different combinations of supplements (nucleobases, vitamins, salts, sodium formate and orotic acid) were added. Constant pH batch fermentation with the modified medium resulted in an EPS yield of approximately 210 mg glucose equivalents per liter medium. This was a 10-fold increase over flask cultivation of this strain in SDM. Although not affecting cell growth, the mixture of salts enhanced the EPS synthesis. Whereas EPS production was approximately 12 mg/g dry biomass without salt supplementation, a significantly higher yield (approximately 20 mg/g dry biomass) was observed after adding the salt mixture. In continuous fermentation, a maximal EPS concentration was obtained at a dilution rate of 0.31/h (80 mg EPS/L), which corresponded to a specific EPS production of 49 mg/g dry biomass.