Degradation of semiconducting polymers by concentrated sunlight

A lens based sunlight concentration setup was used to accelerate the degradation of semiconducting polymers. Sunlight was collected outdoor and focused into an optical fiber bundle allowing for indoor experimental work. Photo-degradation of several polymers was studied by UV-vis absorbance spectroscopy and infra-red spectroscopy. This showed that the degradation rate is significantly increased by increasing illumination intensity. Acceleration factors exceeding 100 compared to standard 1 sun illumination were observed for solar concentration of 200 suns in the case of P3HT. A comparison between infra-red spectra of MEH-PPV degraded at 1 sun intensity and at high solar concentration only showed minor deviations in degradation mechanisms. The acceleration factor was found to vary linearly with the solar concentration. Finally, a comparison of the degradation rates at 1 sun and 100 suns was carried out in a materials study employing five different conjugated polymers relevant to polymer solar cells for which acceleration factors in the range 19-55 were obtained.     

Applicability of X-ray reflectometry to studies of polymer solar cell degradation

Although degradation of polymer solar cells is widely acknowledged, the cause, physical or chemical, has not been identified. The purpose of this work is to determine the applicability of X-ray reflectometry for in situ observation of physical degradation mechanisms. We find that the rough interfaces of the polymer solar cell constituent layers seriously obstruct the sensitivity of the technique, rendering it impossible to elucidate changes in the layer/interface structure at the sub-nanometer level.     

Determination of Total Grain Surface Waxes Using the Iatroscan-Chromarod Technique

The Iatroscan-Chromarod system was used for qualitative and quantitative determination of the total surface waxes of sorghum grain. Grain pearling efficiency was evaluated by comparing the polar compounds extracted with hot benzene at different stages of pearling. Extracted waxes were used as a natural standard to compile a calibration curve for quantitative determinations. A quadratic equation y = a+bx+cx2 was fitted to the areas of standard solutions ranging from 2 to 20 μg/μl. Results were in close agreement with gravimetric determinations and literature values.     

Material Engagement Theory and urban formation: Notes towards a theoretical synthesis

Material Engagement Theory (MET) theorizes artefacts as the emergent outcomes of non-linear processes of formation in which both human and non-human forms of agency are involved. It has proved a useful framework for exploring the architectural design process – which typically involves the mobilisation of multiple tools and materialities – but has not yet been applied to urban design. This paper argues that MET can be applied to the analysis of urban form, helping explain the distributed processes of urban formation. In sketching out an outline theory of urban material engagement, the paper facilitates a dialogue between MET and two theories of urban morphogenesis – SIRN and Space Syntax theory – which explain formal emergence in the urban surface and the urban grid, respectively. Exploring these theories’ analyses of urban formation – and the relationship between urban form and urban social behaviour – the paper outlines a theoretical synthesis which centres on the artefactual nature of urban form.     

Rapid and direct estimation of active biomass on granular activated carbon through adenosine tri-phosphate (ATP) determination

Granular activated carbon (GAC) filtration is used during drinking water treatment for the removal of micropollutants such as taste and odour compounds, halogenated hydrocarbons, pesticides and pharmaceuticals. In addition, the active microbial biomass established on GAC is responsible for the removal of biodegradable dissolved organic carbon compounds present in water or formed during oxidation (e.g., ozonation and chlorination) processes. In order to conduct correct kinetic evaluations of DOC removal during drinking water treatment, and to assess the state and performance of full-scale GAC filter installations, an accurate and sensitive method for active biomass determination on GAC is required. We have developed a straight-forward method based on direct measurement of the total adenosine tri-phosphate (ATP) content of a GAC sample and other support media. In this method, we have combined flow-cytometric absolute cell counting and ATP analysis to derive case-specific ATP/cell conversion values. In this study, we present the detailed standardisation of the ATP method. An uncertainty assessment has shown that heterogeneous colonisation of the GAC particles makes the largest contribution to the combined standard uncertainty of the method. The method was applied for the investigation of biofilm formation during the start-up period of a GAC pilot-scale plant treating Lake Zurich water. A rapid increase in the biomass of up to 1.1 x 10(10)cells/g GAC dry weight (DW) within the first 33 days was observed, followed by a slight decrease to an average steady-state concentration of 7.9 x 10(9)cells/g GAC DW. It was shown that the method can be used to determine the biomass attached to the GAC for both stable and developing biofilms.     

Permeability of low molecular weight organics through nanofiltration membranes

The removal of natural organic matter (NOM) using nanofiltration (NF) is increasingly becoming an option for drinking water treatment. Low molecular weight (LMW) organic compounds are nevertheless only partially retained by such membranes. Bacterial regrowth and biofilm formation in the drinking water distribution system is favoured by the presence of such compounds, which in this context are considered as the assimilable organic carbon (AOC). In this study, the question of whether NF produces microbiologically stable water was addressed. Two NF membranes (cut-off of about 300 Da) were tested with different natural and synthetic water samples in a cross-flow filtration unit. NOM was characterised by liquid chromatography with organic carbon detection (LC-OCD) using a size-exclusion column in addition to specific organic acid measurements, while AOC was measured in a batch growth bioassay.Similarly to high molecular weight organic compounds like polysaccharides or humic substances that have a permeability lower than 1%, charged LMW organic compounds were efficiently retained by the NF membranes tested and showed a permeability lower than 3%. However, LMW neutrals and hydrophobic organic compounds permeate to a higher extent through the membranes and have a permeability of up to 6% and 12%, respectively. Furthermore, AOC was poorly retained by NF and the apparent AOC concentration measured in the permeated water was above the proposed limit for microbiologically stable water. This indicates that the drinking water produced by NF might be biologically unstable in the distribution system. Nevertheless, in comparison with the raw water, NF significantly reduced the AOC concentration.     

Infrared Heating as a Disinfestation Method Against <Emphasis Type="Italic">Sitophilus oryzae</Emphasis> and Its Effect on Textural and Cooking Properties of Milled Rice

Infrared (IR) heating method against rice weevils (Sitophilus oryzae) in an egg stage was investigated. A kinetic model was developed to describe insect mortality in a temperature range of 40–60 °C. Effects of IR heating temperature (50–60 °C) and exposure time (1–3 min) on insect mortality and quality attributes of the treated rice were evaluated. The optimized condition obtained by means of the response surface method was used to analyze rice quality before and after IR treatment with storage. The results showed that the 0.5th-order thermal death kinetic equation was the most suitable model, and the S. oryzae eggs had less heat tolerance than the adults and some other species. Mortality achieved 100 % after 2 min for all temperatures. Both IR heating parameters significantly affected the treated milled rice qualities. The minimal changes in rice quality before and after storage could be obtained using optimized temperature and exposure time of 53.6 °C and 1.2 min, respectively.     

Modelling and Characterisation of the Texture Development in the Fusion Zone of An Austenitic Weld

The relation between texture and microstructure and the macroscopic solidification direction has been investigated for an austenitic 316L stainless steel weld. The fusion zone has been characterised by EBSD. Texture development has been simulated by thermal Finite Element Analysis coupled with a simple model of preferential <100>‐oriented solidification following the solidification direction. The thermal part is validated by means of thermocouple measurements at several locations on the specimen. The predicted texture is in very good agreement with the measured one.