X gene and precore region mutations in the hepatitis B virus genome in persons positive for antibody to hepatitis B e antigen: comparison between asymptomatic "healthy" carriers and patients with severe chronic active hepatitis

Hepatitis B virus (HBV) carriers with antibody to hepatitis e antigen comprise asymptomatic carriers (ASCs), who have low replication levels of HBV, and patients with chronic active hepatitis (CAH), who have high levels of viral replication. To investigate whether defects in the X protein might be responsible for this difference in the level of viral replication, nucleotide sequences of X and precore gene regions in serum HBV were analyzed in 19 ASCs and 9 CAH patients. All patients had a point mutation creating a stop codon in the precore region. Seventeen ASCs (87.3%) had identical mutations consisting of 4 noncontiguous 1-bp deletions or an 8-bp deletion, both of which truncate the normal X protein, whereas no CAH patient had an X gene mutation (P < .001). Thus, deletion of the X protein might be responsible for the low levels of viral replication in ASCs.     

Development of 170 GHz/500 kW gyrotron

A development of 170GHz/500kW level gyrotron was carried out as R&D work of ITER. The oscillation mode is TE_31,8. In a short pulse experiment, the maximum power of 750kW was achieved at 85kV/40A. The efficiency was 22%. In the depressed collector operation, 500kW/36%/50ms was obtained. The maximum efficiency of 40% was obtained at P_RF=470kW whereas the power decrease by the electron trapping was observed. Pulse extension was done up to 10s at P_RF=170kW with the depressed collector operation. The power was limited by the temperature increase of the output window.     

Inter- and intra-molecular ionic interactions of polyampholyte: Carboxymethyl-2-diethylaminoethylcellulose

Carboxymethyl-2-diethylaminoethylcellulose (CM-DEAE cellulose) was prepared by etherification of carboxymethylcellulose with diethylaminoethyl chloride in a NaOH solution. The behaviour of CM-DEAE cellulose in aqueous solution was studied by viscosity and GPC measurements. The degree of substitution (DS) and existing states of DEAE substituents were examined by the use of proton NMR, and those of the CM substituents were observed with FT-IR. The results reveal that the reduced viscosity and apparent molecular size of CM-DEAE cellulose vary with the concentration of sodium chloride and changes in pH and DS. These phenomena can be explained in terms of inter- and intra-molecular ionic interactions.     

Damage tolerance of glass mat/epoxy laminates hybridized with flexible resin under static and impact loading

This study deals with the impact property and damage tolerance of matrix hybrid composite laminates with different laminate constitution. The matrix hybrid composite laminates consisted of the laminae with a conventional epoxy resin and the laminae with a flexible epoxy resin modified from the conventional resin to avoid the interlaminar delamination. The impact energy absorption ratio greatly depended on the matrix resin placed at the impact face. The energy absorption was almost constant if the conventional resin was placed at the impact surface layer, while it increased exponentially with the increasing fraction of the flexible resin if the flexible resin was placed at the impact face. The impact energy was absorbed by the damage development and propagation in the laminate with conventional resin laminae as the impacted face, while it was absorbed by both the recoverable deformation of the flexible resin and the damage propagation in the laminate with flexible resin laminae as the impacted face.     

Lipid-Lowering Effect of Eriocitrin, the Main Flavonoid in Lemon Fruit, in Rats on a High-Fat and High-Cholesterol Diet

ABSTRACT:  Eriocitrin (eriodictyol 7- O -β-rutinoside) is the main flavonoid in lemon fruit. In this study, eriocitrin was investigated for its lowering effect on serum and hepatic lipids in high-fat and high-cholesterol fed rats. Rats in the control group ( N = 6) were fed a 20% lard and 1% cholesterol diet for 21 d, and rats in the 0.35% eriocitrin group ( N = 6) and 0.70% eriocitrin group ( N = 6) were fed a diet supplemented with eriocitrin 0.35% and 0.70%, respectively. The content of hepatic total cholesterol and triglyceride in the eriocitrin group was no different from that of the control group. The total cholesterol, VLDL+LDL, triglyceride, and phospholipid in the serum of the 0.35% eriocitrin group showed significantly lower concentrations than the control group ( P < 0.05), although there was no difference in the HDL concentrations among the groups. The lowering effect of eriocitrin for serum total cholesterol was thought to be caused by a decrease in VLDL+LDL. The 0.35% eriocitrin group was shown to have a significant increase in excretion of fecal bile acid ( P < 0.05) and a tendency for enhanced hepatic m-RNA levels of LDL receptor in comparison with the control group.     

The oxidation properties of fourth generation single-crystal nickel-based superalloys

The fourth-generation nickel-based single-crystal superalloys, which contain large amounts of refractory metals for strengthening and platinum group metals for topologically close-packed phase prevention, show excellent high-temperature strength. However, these alloying elements seem to decrease high-temperature oxidation resistance. In this study, nickel-based superalloys with various amounts of tantalum, rhenium, and ruthenium were examined in isothermal and cyclic exposures at 1,100°C to investigate the effect on the oxide growth rate and resistance to scale spallation. Ruthenium and rhenium were found to degrade the oxidation resistance by the vaporization of their oxide. Tantalum-rich oxide in the spinel layer acts to stabilize ruthenium and rhenium oxide in the scale. The addition of hafnium and yttrium is effective in improving the oxidation resistance of ruthenium-containing nickel-based superalloys.     

Influence of third monomer on the crystal phase transition behavior of ethylene-tetrafluoroethylene copolymer

Crystal phase transition between the low- and high-temperature phases has been investigated for ethylene (E)-tetrafluoroethylene (TFE) alternating copolymer (ETFE) containing the third monomeric species by the temperature dependent measurements of wide-angle X-ray diffraction (WAXD) and small-angle X-ray scattering (SAXS) and differential scanning calorimetry. Nonafluoro-1-hexene (NFH) and hexafluoropropylene (HFP) were chosen as the third monomers, where they are different in the side-branch length, -(CF₂)₃CF₃ and -CF₃, respectively. In the case of E/TFE/NFH copolymer (ET-C4F9), the crystal phase transition temperature of the original ETFE two-components copolymer was not very much affected by the existence of NFH in the range of NFH content from 0.7 to 3 mol%. Contrarily, the crystal phase transition temperature of E/TFE/HFP copolymer (ET-CF3) was found to decrease drastically with increasing HFP content. The melting temperature and the higher-order structure were also affected sensitively depending on the HFP content. This difference in phase transition behavior between ET-C4F9 and ET-CF3 copolymers is reasonably interpreted as follows: the short side groups (-CF₃) of HFP monomeric unit are included in the crystal lattice of E/TFE chains and the unit cell is expanded gradually with an increment of the HFP content, resulting in the decrease in phase transition point because of easier thermal motion of the chains. On the other hand, the long side groups [-(CF₂)₃CF₃] of NFH monomeric units are excluded out of the crystal lattice and located on the lamellar surfaces or in the amorphous region and do not affect very much the phase transition temperature even when the NFH content is increased. In association with such a change in crystal structure, the long period of stacked lamellar structure was found to decrease remarkably in the case of NFH, whereas it does not change very much for HFP, consistent with the interpretation of the above-mentioned WAXD data.     

Using a GPU to Accelerate Die and Mold Fabrication

The authors present a GPU-based method for generating and verifying cutter paths for numerically controlled milling. A CAM system based on this technology is now employed in production at Mazda Motor Corporation for manufacturing stamping dies. This system can compute cutter paths more than 20 times faster than previous methods     

Electrode pitting in resistance spot welding of aluminum alloy 5182

Electrode pitting was investigated in resistance spot welding of 1.5-mm-thick sheet aluminum alloy 5182 using a medium-frequency direct-current welder and electrodes with a tip face curvature radius of 50 mm and tip face diameter of 10 mm. Detailed investigation of the metallurgical interactions between the copper electrode and aluminum alloy sheet was carried out using scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDX) and X-ray diffraction (XRD). The results indicated that electrode degradation, which eventually leads to weld failure, proceeded in four basic steps: aluminum pickup, electrode alloying with aluminum, electrode tip face pitting, and cavitation. Since pitting and cavitation result from Al pickup and alloying, periodic electrode cleaning could extend electrode tip life by limiting the buildup of Al on the tip face. This work is part of the effort to improve electrode tip life in resistance spot welding of aluminum alloys for automotive applications.