酚醛树脂复合板在热连轧机中的应用

重点分析了现有F7机架出口导卫装置的情况。原导卫材料是由铸钢制造 ,由于摩擦和高温常常引起热连轧带钢表面划伤 ,根据现场实际情况用酚醛树脂复合板替代铸钢导卫装置。实践表明 ,这种改造即可行又可靠 ,并取得了好的效果     

钕电解阳极过电位的测定

用慢扫描示波法测定了钕电解的阳极过电位 .考察了温度、阳极电流密度、Nd2 O3添加量、电解质组成等因素对阳极过电位的影响 ,探讨了降低阳极过电位的可能途径 .结果表明 ,阳极过电位随阳极电流密度的增加而增大 ,随温度的升高而减小 ,一定范围内 ,阳极过电位与阳极电流密度的对数呈线性关系 ,满足塔菲尔方程 ;电解质中LiF和Nd2 O3浓度增加 ,阳极过电位降低 ;适当控制阳极电流密度、升高温度、增加电解质中LiF和Nd2 O3的浓度并尽可能减小极间距 ,均有利于降低阳极过电位     

溶胶-凝胶生物玻璃多孔材料显微结构和生物活性的扫描电镜及红外光谱分析

本文利用溶胶．凝胶法制备了CaO-P2O5-SiO，系统生物活性玻璃，并以其为原料制备了用于骨修复及骨组织工程支架的块状生物活性材料。利用体外实验方法(invitro)结合x射线衍射(XRD)、扫描电子显微镜(SEM)和傅立叶变换红外光谱分析(FTIR)技术对不同烧结工艺制备的材料结构、晶相和生物活性的影响进行了分析研究。研究表明，经800℃和1100℃烧结5min的两种材料均有硅磷酸钙Ca5(PO4)2SjO4微晶相析出。烧结温度越高，析出微晶相的体积比例越大，材料的生物活性则越低。在模拟生理溶液中碳酸羟基磷灰石(HCA)只在烧结体中的玻璃颗粒表面形成，而在其硅磷酸钙Ca5(PO4)2SiO4微晶相表面未发现HCA形成。     

苯乙烯与1-(2-叔丁基过氧异丙基)-3-异丙烯基苯共聚行为研究

苯乙烯与1－（2－叔丁基过氧异丙基）－3－异丙烯基苯（D120）能进行自由基共聚合反应，聚合后过氧基团以侧基的形成被保留在共聚物大分子链上，凝胶色谱分析发现，随原料单体中D120比例增加，共聚物的分子量减小，分子量分布变窄，DSC分析发现共聚物中过氧基团的分解温度随D120结构单元含量的增加而下降，但仍高于D120单体过氧基团的分解温度，苯乙烯与D120的竞聚率为：rD120=0.700,rSt=0.714。     

Complex amplitude estimation in the known steering matrix and generalized waveform case

We consider a special growth-curve (SGC) model with a known steering matrix and generalized waveform in the presence of unknown interference and noise. Several estimators of the complex amplitude based on this model are derived, including the methods of approximate maximum likelihood (AML), minimum variance distortionless response (MVDR), and amplitude and phase estimation (APES). We analyze the statistical properties of these estimators and show that in the presence of temporally white but spatially correlated noise and interference, AML is asymptotically statistically efficient for a large snapshot number while MVDR and APES are asymptotically equivalent but not statistically efficient. Via several numerical examples, we also show that when the noise and interference are both spatially and temporally correlated, the APES estimator can achieve better estimation accuracy and exhibit greater robustness than the other methods.     

Design of photonic crystal fibers for dispersion-related applications

A general procedure for design of photonic crystal fibers (PCFs) with desirable dispersion properties is presented. The design model is based on the combination of a rigorous vector mode solver and a scaling transformation for the dispersion properties of the PCFs. In comparison with the conventional design method, the new design procedure is more efficient and can be readily automated for the purpose of design optimization. Several applications of the design procedure, e.g., the design optimization for dispersion shifted fibers, dispersion flattened fibers, and dispersion compensation fibers, are demonstrated and discussed.     

Orthogonal space-time block codes: maximum likelihood detection for unknown channels and unstructured interferences

Space-time coding (STC) schemes for communication systems employing multiple transmit and receive antennas have been attracting increased attention. The so-called orthogonal space-time block codes (OSTBCs) have been of particular interest due to their good performance and low decoding complexity. In this paper, we take a systematic maximum-likelihood (ML) approach to the decoding of OSTBC for unknown propagation channels and unknown noise and interference conditions. We derive a low-complexity ML decoding algorithm based on cyclic minimization and assisted by a minimum amount of training data. Furthermore, we discuss the design of optimal training sequences and optimal information transfer to an outer decoder. Numerical examples demonstrate the performance of our algorithm.     

八钢70t电弧炉冶炼弹簧钢钢液中氮含量的控制

针对EAF-LF-CCM（电炉一精炼炉一连铸）冶炼弹簧钢过程中钢液氮的控制进行了工业试验.试验表明：电炉冶炼过程中主要是电弧区增氮及出钢过程的增氮,精炼炉及连铸过程增氮主要是钢液与大气接触,通过试验对电炉短流程生产优钢过程中的氮含量的控制起到指导作用.     

山西铝厂锅炉水冷壁膨胀异常原因分析及对策

针对山西铝厂160t／h锅炉在实际运行中膨胀异常的问题，对不同的施工方法下，水冷壁膨胀量是否正常这一问题进行分析，找出了水冷壁膨胀异常的原因，并提出了解决对策。     

位置灵敏探测器数据采集的软件设计

介绍了一个基于Windows操作系统的数据采集软件，该软件用于使用重心法确定的位置信息的位置灵敏探测器，具有方便的人机交互界面，使用专用驱动程序采集数据。