油酸臭氧化制备壬二酸

对以臭氧为氧化剂 ,由油酸制备壬二酸的工艺进行了研究 ,并讨论了各主要因素如溶剂与油酸的体积比、臭氧化温度、催化剂的种类和用量以及氧化分解时间对反应的影响。结果表明 :当臭氧化温度为 2 5～ 30℃ ,催化剂用量质量约为油酸的 0 .0 8%～ 0 .12 % ,氧化分解温度为 90～ 95℃ ,反应时间为 2 .5h ,壬二酸的收率为 4 7.1%。     

Effect of polymerization conditions on o‐phenylenediamine and o‐phenetidine oxidative copolymers

A series of new o‐phenylenediamine (OPD)/o‐phenetidine (PHT) copolymers with partly phenazine‐like structures has been successfully synthesized at three polymerization temperatures by chemically oxidative polymerization in four different polymerization media. The molecular structures and properties of the resulting OPD/PHT polymers were investigated by IR, UV–vis and high‐resolution ¹H NMR spectroscopies, and DSC, in order to ascertain the effect of reaction temperature, comonomer ratio and acid medium. The copolymerization mechanism of OPD with PHT monomers has been proposed. It is found that the statistical OPD/PHT copolymer obtained at a temperature of 118 °C has a higher degree of polymerization than that obtained at 12–17 °C. The OPD content in the copolymers calculated from NMR spectroscopic analysis is higher than that in the feed OPD content, whereas the OPD content calculated from element analysis is slightly lower than the feed OPD content. It can be predicted that denitrogenation takes place in the OPD units during the polymerization process at OPD/PHT molar ratios of 90/10 and 100/0. These OPD/PHT copolymers exhibit a much better solubility than the OPD homopolymer, hence suggesting an incorporation of PHT units into the phenazine structure of the homopolymer. The thermal behavior of the copolymers was also studied. Copyright © 2004 Society of Chemical Industry     

MMSE-optimal approximation of continuous-phase modulated signal as superposition of linearly modulated pulses

The optimal linear modulation approximation of any M-ary continuous-phase modulated (CPM) signal under the minimum mean-square error (MMSE) criterion is presented in this paper. With the introduction of the MMSE signal component, an M-ary CPM signal is exactly represented as the superposition of a finite number of MMSE incremental pulses, resulting in the novel switched linear modulation CPM signal models. Then, the MMSE incremental pulse is further decomposed into a finite number of MMSE pulse-amplitude modulated (PAM) pulses, so that an M-ary CPM signal is alternatively expressed as the superposition of a finite number of MMSE PAM components, similar to the Laurent representation. Advantageously, these MMSE PAM components are mutually independent for any modulation index. The optimal CPM signal approximation using lower order MMSE incremental pulses, or alternatively, using a small number of MMSE PAM pulses, is also made possible, since the approximation error is minimized in the MMSE sense. Finally, examples of the MMSE-optimal CPM signal approximation and its comparison with the Laurent approximation approach are given using raised-cosine frequency-pulse CPM schemes.     

A PIN diode controlled variable attenuator using a 0-dB branch-line coupler

We describe a simple PIN diode controlled variable attenuator that employs a 0-dB branch line directional coupler. The response of the attenuator was measured between 1.3 GHz and 2.6 GHz. At the center frequency, the attenuation monotonically varied from 0.7 dB to 23 dB with the control voltage, and the distributed branch-line coupler structure resulted in low input reflection. Our attenuator is easier to design, smaller in area than a double hybrid coupled attenuator, and has comparable or better reflection and attenuation performance characteristics.     

宣钢烧结生产配加钢渣的工业试验

总结了宣钢烧结配配加钢渣生产不同碱度烧结矿的工业生产试验，提出了配加钢渣可强化全精粉烧结。     

固体润滑涂层的评价和使用

本文主要介绍了二硫化钼，石墨、聚四氟乙烯三种固体润滑涂层的特点以及润滑涂层摩擦磨损性能的评价手段和方法，以及台架试验和应用实例，提出了选用方法和步骤。     

小剂量辐照小鼠胸腺细胞膜流动性的变化

报道了以茈为荧光探针,探讨小剂量~(60)Co γ射线照射后小鼠胸腺细胞膜流动性的变化。结果表明,剂量在0.25-1.00Gy范围,胸腺细胞膜流动性降低与剂量之间呈明显线性关系。从0.50Gy起,辐照组荧光强度比值I_1/I_2与I_3/I_2与对照组的比较存有显著差异(P<0.05)。提示淋巴细胞膜流动性的变化可作为小剂量辐照早期效应的敏感指标。     

破片式战斗部优化设计技术研究

侧重研究了破片式战斗部装药外形的优化设计技术。提出了装药外形与破片飞散特性（如破片飞散角，分布带宽等）之间的数学描述；建立了圆弧和对数螺线装药外形母线与战斗部其他设计参数间的数学模型。在假定约束条件下，优化设计了破片了聚焦式战斗部的结构参数；静爆试验结果表明，破片分布与理论计算吻合较好。     

提高连铸浊环水水质浅析

介绍了太钢板坯连铸水处理系统的工艺流程，分析了连铸浊环水水质存在的问题。通过对冷却塔部分、铁皮坑、水泵调速等改造，以及选用新的水质稳定剂，使水质明显好转。