The band areas of proteins determined by fluorescent scanning in the commercial automated gel electrophoresis apparatus

An automated gel electrophoresis apparatus, recently available commercially, allows one to follow the band during electrophoresis in real time, and lends itself therefore to an evaluation of bandwidth as a function of migration time (the dispersion coefficient), resolution and band shape. These determinations assume the constancy of band area with migration time and at various gel concentrations. The purpose of the present study was to verify these assumptions. Representative proteins and sodium dodecyl sulfate (SDS)-proteins, either natively fluorescent or fluorescein carboxylate labeled, were found to exhibit band areas which approach constancy as a function of migration time in both agarose and polyacrylamide gel electrophoresis, provided that (i) the protein concentration under the band was low enough to obviate self-quenching of fluorescence; (ii) the separation of the protein of interest from contaminants had progressed sufficiently during the time at which band areas were measured; (iii) the baseline under the peak was sufficiently well defined. However, band areas decrease with increasing gel concentration. Protein peaks exhibited leading and trailing tails. The ratio of the combined tail area to total area appeared to be near-constant at varying migration times. However, that ratio increases with increasing gel concentration. The tail area does not appear to be an artifact of fluorometric detection since it is reproduced upon fluorimetric analysis of the protein eluted from gel slices after electrophoresis. However, it may be due to photochemical destruction under the conditions of repetitive fluorometric peak detection.     

Deformation and fracture of glass bead/ CTBN-rubber/epoxy composites

Carboxyl-terminated butadiene-acrylonitrile-rubber decreases modulus and yield stress of the studied epoxy but increases fracture toughness. The addition of glass bead compensates for the loss in modulus but has little effect on yield stress. However, it significantly contributes to the fracture toughness by providing additional mechanisms for toughening of both the unmodified and rubber-modified epoxy. For the toughened epoxies studied, fracture surfaces gave only limited information on fracture mechanisms since significant energy absorption also occurs in the material below the fracture surface. Suggestions for suitable material compositions for fiber composite matrices are given.     

Optical fiber solitons, their properties and uses

The history and mathematical formulation of solutions are briefly reviewed. Solitons of the nonlinear Schrodinger equation are studied in greater detail because they describe nonlinear pulse propagation on dispersive optical fibers. The proposal by A. Hasegawa and the experiments of L.F. Mollenauer on long distance soliton propagation for use in repeaterless transoceanic fiber transmission cables are described. In 1986, limitations on the distance that can be spanned by a repeaterless link for a given bit rate were shown to exist. It has been shown recently that by proper design these limitations can be overcome, so that newer transoceanic cable designs are likely to utilize solitons. The special properties of solitons make them particularly suited for all optical switching and logic operations. Some recent experiments with such switches are described     

Tunable wavelength filters based on nonlinear optical interactionsin semiconductor amplifiers

A novel class of narrow-band tunable wavelength filters is proposed and evaluated. Wavelength selectivity of the proposed filters Is derived from the finite time response of an optical nonlinearity. The nonlinearity is gain saturation in semiconductor optical amplifier structures. The filters are shown to have very narrow passbands tunable over the entire semiconductor gain bandwidth. The key to filter implementation is a device configuration in which the wave-mixing products can be isolated from the amplified inputs. Three integrated optics compatible configurations are considered and shown to have high filter throughputs 34 to 180% and subangstrom bandwidths     

Monitoring systems and determination of actual fatigue usage

At GKN, fatigue monitoring of important components has been conducted since 1979. The monitoring methods depend on the mechanisms of damage; quasi-static loads are regarded as well as dynamic loads. The components were selected for monitoring on the basis of a system analysis. The data resulting from monitoring are used to optimise operation mode steadily. Experience shows that the use of monitoring data as input for fatigue assessment is the most realistic and cost-effective way. This fatigue assessment uses global and local sensitivity studies to evaluate the load-stress relation for each component. These relations can be programmed to produce stress vs. time curves. These are processed according to ASME rules to give a realistic fatigue usage.     

A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.