Mikromethode zur quantitativen Bestimmung von Coffein

Zusammenfassung Zur quantitativen Bestimmung von Coffein in biologischem Material wird ein kombiniertes Verfahren aus Dünnschichtchromatographie und Densitometrie beschrieben. Das Verfahren läßt Bestimmungen im Nanogramm-Bereich zu. Das Probenvolumen liegt unter 100 l.Die Proben — Capillarblut — werden zunächst mit dem gleichen Volumen Chloroform extrahiert. Anschließend wird das Coffein mittels Dünnschichtchromatographie von Begleitstoffen und störenden Substanzen abgetrennt. Es werden Kieselgel-60-Fertigplatten und Chlorofom/Aceton (9 + 1; v/v) als Fließmittel verwendet, dabei beträgt die Laufzeit 30 min.Die quantitative densitometrische Auswertung erfolgt durch Remissionsmessung bei 273 nm. Im Bereich von 10–60 ng Coffein/Fleck verläuft die Eichkurve linear. 1 mg/I Coffein kann noch sicher quantitativ erfaßt werden. Die Nachweisgrenze liegt bei 0,1 mg/1.

---

A quantitative micromethod for the caffeine determination

Summary A combined procedure with thin-layer-chromatography and densitometry is described for the quantitative estimation of caffeine in biological material. This method ist applicable in the nanogram range. Test samples of less than 100 l may be used. The samples (capillary-blood) are extracted with the same volume of chloroform. Caffeine is separated from interfering compounds by thin-layer-chromatography. Commercial silica-60-plates with chloroform/acetone (9 + 1; v/v) as solvent are used. The running time is about 30 min. The quantitative densitometric determinations are performed in the remission mode at 273 nm. In the range from 10 to 60 ng/spot the calibration curve is linear. Accurate quantitative data will be obtained even at concentrations of 1 mg/1 caffeine. The detection limit is at about 0.1 mg/1.

     

Rotary Blanking ‐ a New Manufacturing Process

Rotary blanking is a method of blanking and punching with rotating tools whereby the cutting tools are fixed to a pair of rollers performing a continuous blanking operation on a strip of sheet metal. The purpose of this paper is to outline the determining conditions under which the rotary blanking process takes place and to discuss advantages, restrictions, applications and optimization of this technology.     

Metallurgical Development in Steel‐plant‐internal Multi‐injection Hot Metal Desulphurisation

The use of thermodynamic, statistical, and light and electron‐optical microscopic methods has made it possible to analyse the course of reactions during steel‐plant‐internal hot metal desulphurisation. The theoretical dependence between oxygen and sulphur activity has been used to develop an EMF‐measurement‐based technique for determining the sulphur content as the hot metal is desulphurised. The absence of magnesium sulphide from the collection of phases in the final slag because of the greater stability and secondary formation of calcium sulphide has been explained with the aid of thermo‐chemical calculations.     

Physiological cost of energy-equivalent noise exposures with a rating level of 85 dB(A):: Hearing threshold shifts associated with energetically negligible continuous and impulse noise

In industry continuous or impulse noise does not occur exclusively; rather it is a combination of both. If low-level continuous noise or impulse noise (below 120 dB) is added to an already existing high-level continuous noise this often numerically causes no essential increase in the rating level. Yet, it cannot be expected that also aural strain of these exposures is always negligible. Therefore, in a cross-over test series, ten male subjects (Ss) were exposed to white noise of 94 dB(A) for 1 h (TS I), energy-equivalent to an 8 h-rating level L_Ard of 85 dB(A). In a second test series (TS II) the same exposure was combined with 900 energetically negligible 5-ms impulses with a noise level of 113 dB(A) which increased the rating level by only 0.4 dB. The noise exposure of TS I and TS II was followed by an idealized resting phase in a soundproof cabin. In a third test series (TS III) the continuous noise of 94 dB(A) / 1 h was followed by 3 h of white noise at 70 dB(A). Such an additional load increases the L_Ard by merely 0.1 dB to 85.1 dB(A). In all three test series, the noise-induced temporary threshold shift (TTS₂) and its restitution were measured. The continuous noise exposure of 94 dB(A) for 1 h was associated with a TTS₂ of around 20 dB which disappeared completely after about 2 h. The additional impulse noise caused a small increase in the TTS₂ and a prolongation of the restitution time. The maximum mean temporary threshold shift for the group increased only slightly (from 22.5 to 25.9 dB, which nevertheless can be statistically proven at a significance level of p 0.99). Yet, more importantly, the restitution time increased from 126 to 175 min, i. e. 3 h, which can be statistically proven at a significance level of p0.95. The TTS₂-values of TS III did not differ significantly from those resulting from TS I. That was expected as the conditions up to that point in time were identical. But due to the additional subsequent exposure, the mean restitution time increased considerably from 126 min up to 240 min (4 h). The mean total physiological cost represented by the integrated restitution temporary threshold shift (IRTTS) increased in TS II by approximately 40% and in TS III even by 140%.

Relevance to industry

The results of the study show that levels of noise which have no influence on the rating level which traditionally is calculated according to the energy-equivalence principle are often of great importance, as they can lead to considerably prolonged restitution times. Therefore, the purely energy-equivalent determination of the rating level of both impulse noise and low sound levels can lead to an underestimation of latent problems so that over time a reversible TTS can evolve into a permanent threshold shift. The results are also of importance for the acoustic design of break rooms for noise-exposed workers. There should be conditions that allow an undisturbed restitution of hearing.     

RFID security

Radio Frequency Identification (RFID) systems have become popular for automated identification and supply chain applications. This article describes the technical fundamentals of RFID systems and the associated standards. Specifically, we address the security and privacy aspects of this relatively new and heterogeneous radio technology. We discuss the related security requirements, the threats and the implemented mechanisms. Then the current security and privacy proposals and their enhancements are presented. Finally we discuss the role of this technology in Ubiquitous Computing.