InGaAs angled-grating distributed Bragg reflector lasers integrated with grating outcoupler for collimation

An angled-grating distributed Bragg reflector (DBR) laser integrated with a grating outcoupler (GO) is proposed and demonstrated. It consists of an angled broad-area gain stripe surrounded by angled DBR (/spl alpha/-DBR) gratings parallel to the gain stripe and two DBR gratings for feedback at the stripe ends, and a GO for emitting a collimated output beam. Due to distributed Bragg reflection in the /spl alpha/-DBR gratings, filamentation can be suppressed. Single-mode lasing up to 69 mW peak power was obtained under pulse condition. A collimated output beam with divergence angles, close to the diffraction limit, was obtained. These results confirm the effectiveness of the /spl alpha/-DBR gratings.     

Combinatorial pulsed laser deposition and thermoelectricity of (La1−xCax)VO3 composition-spread films

La_1−xCa_xVO₃ composition-spread film library was fabricated by combinatorial pulsed laser deposition and their thermoelectric properties were evaluated paralelly by the multi-channel probes of Seebeck coefficient and electric conductivity. Concurrent X-ray analysis verified the formation of solid soluted films in the full composition range (0x1) as judged from the linear variation of the lattice constants. The Seebeck coefficients of La_1−xCa_xVO₃ changed from a large negative value to almost zero with the increase of x, due presumably to the variation of valence in vanadium ions.The power factor in this library was as high as 0.6 μW/cm K², which was obtained at x=0, i.e. pure LaVO₃ grown at 800 °C.     

38. R&D on hydrogen production by high-temperature electrolysis of steam

One of the objectives of the high-temperature engineering test reactor (HTTR) is to demonstrate the effectiveness of high-temperature nuclear heat utilization, which aims to extend the application of nuclear heat to non-electric fields, especially to hydrogen production. As part of the development of the hydrogen production processes, laboratory-scale experiments of a high-temperature electrolysis of steam (HTES) had been carried out with a practical electrolysis tube with 12 solid-oxide cells connected in series. Using this electrolysis tube, hydrogen was produced at the maximum density of 44 N cm³/cm² h at a electrolysis temperature of 950 °C. Thereafter, to improve hydrogen production performance, a self-supporting planar electrolysis cell with a practical size (80 mm × 80 mm of electrolysis area) was fabricated. In the preliminary electrolysis experiment carried out at 850 °C, the planar cell produced hydrogen at the maximum density of 38 N cm³/cm² h, and the energy efficiency was almost as high as that obtained with the electrolysis tube at 950 °C. However, both electrolysis tubes and planar cells did not keep their integrity in one thermal cycle. Durability of the solid-oxide cell against the thermal cycle is one of the key issues of HTES.     

TRADE‐OFF BETWEEN APPROXIMATION ACCURACY AND COMPLEXITY FOR TS FUZZY MODELS

This paper proposes a transformation method that serves the trade‐off between the modelling complexity and accuracy of multi‐variable Takagi‐Sugeno fuzzy inference operator‐based modelling (TS fuzzy modelling). The relation between the number of fuzzy rules and the modelling accuracy is defined in the paper. The proposed transformation method is capable of finding the minimal number of fuzzy rules for a given accuracy of a given TS fuzzy model. A case study, focusing on a benchmark problem of fault diagnosis, developed in the framework of EC‐founded Research Training Network DAMADICS, of an actuator in a sugar factory, is presented to provide feasibility of the proposed method.     

Effect of chitosan-gluconic acid conjugate/poly(vinyl alcohol) cryogels as wound dressing on partial-thickness wounds in diabetic rats

We previously developed chitosan cryogels from chitosan-gluconic acid conjugate without using toxic additives for wound care. In this study, we improved physiological characteristics of the previous cryogels by incorporating poly(vinyl alcohol) that also form cryogels. Mechanical strength of the cryogels was more than two times higher than that of the previous cryogels. Furthermore, the incorporation of poly(vinyl alcohol) enhanced water retention and resistance to degradation of the gels by lysozyme. The cryogels retained the favorable biological properties of the previous cryogels that they accelerate infiltration of inflammatory cells into wound sites. Time period for repairing 50 % of initial area of partial-thickness skin wound treated with the cryogels (4.0 ± 1.1 days) was shorter than those with gauze (6.5 ± 0.3 days) or a commercial hydrogel dressing (5.7 ± 0.3 days). Finally, we confirmed that incorporation of basic fibroblast growth factor into the cryogels was effective to further accelerate wound healing (2.7 ± 1.0 days). These results demonstrate that the cryogels in this study are promising for wound care.     

Three-dimensional rainbow schlieren measurements in underexpanded sonic jets from axisymmetric convergent nozzles

The rainbow schlieren deflectometry has been combined with the computed tomography to obtain three-dimensional density fields of shock containing free jets and we call the method the schlieren CT. Experiments on the schlieren CT have been performed at a nozzle pressure ratio of 4.0 by using an axisymmetric convergent nozzle with an inner diameter of 10 mm at the exit where the nozzle was operated at an underexpanded condition. Multidirectional rainbow schlieren pictures of an underexpanded sonic jet can be acquired by rotating the nozzle about its longitudinal axis in equal angular intervals and the three-dimensional density fields are reconstructed by the schlieren CT. The validity of the schlieren CT is verified by a comparison with the density fields reconstructed by the Abel inversion method. As a result, it is found that excellent quantitative agreement is reached between the three-dimensional jet density fields reconstructed from both methods.     

Degradation behavior of moduli in extruded pure magnesium during low- to giga-scale cyclic tension fatigue

The mechanical properties of extruded pure magnesium during cyclic tension fatigue in the low- to giga-scale regime at room temperature have been investigated using ultrasonic reflection methods with longitudinal and shear waves. The acoustic velocities and calculated Young’s and shear moduli decreased by a large percentage with an increase in the number of cycles in all cycle modes due to growth of grain boundary voids. The eventual degradation of the properties was largest during giga-cycle fatigue, in which the moduli decreased by ～9%. The elastic behavior depended on the drive stress and the number of cycles rather than on fatigue time. Longitudinal and shear wave propagation characteristics and investigations of a grain boundary before and after fatigue using electron backscatter diffraction based on field-emission scanning electron microscopy and focused ion beam transmission electron microscopy revealed that the largest boundary void gap width was less than several nanometers (almost closed). The Poisson’s ratio and bulk modulus were affected notably by the void gap, in which the threshold corresponds to the longitudinal wave amplitude. Other damage phase data were determined using scanning electron microscopy, Vickers hardness, and surface roughness tests under progressive fatigue; these results also indicated slight grain boundary degradation.     

Shape memory properties of polypeptide hydrogels having hydrophobic alkyl side chains

Polypeptide hydrogels were prepared by cross-linking of hydrophobically-modified poly[N⁵-(2-hydroxyethyl) l-glutamine] having alkyl side chains –C_nH_2n+1. Chain length of the alkyl group was n = 8, 16, and 18, and their mole fractions in the polypeptide were varied in the range of 0.05–0.16. Shape memory ability of the prepared polypeptide hydrogels was investigated. After deformation at 60 °C, the hydrogel was cooled in order to fix the temporary deformed shape. It was found that crystallization of the alkyl side chains did not occur, and the fixation ability of the hydrogel at 0 °C was low. In the subsequent heating process, the deformed temporary shape spontaneously recovered to the original shape gradually with increasing temperature, in other words, the shape recovery ratio varied with depending on the recovery temperature. From these observations, it was proposed that the shape fixation of the polypeptide hydrogel was achieved by strong segregation of the hydrophobic alkyl chains at low temperature, and the shape recovery of the deformed hydrogel was accompanied by the gradual decrease of the segregation strength with the temperature increase.     

Supramolecular morphology of two-step melt-spun poly(dioxanone) fibers

Structure of poly(dioxanone) (PPDX) fibers produced through a two-step melt-spinning process with an additional short-period annealing above the melting temperature of PPDX was investigated and the effect of annealing on the degradation behavior was discussed. The morphological study carried out by etching the fibers using a phosphate or permanganate solution suggested that the fibers take a skin–core structure, and both the skin layer and the core region consist of a bundle of microfibrils. The micro-beam X-ray diffraction analysis revealed that the short-period annealing in the production process only slightly promotes the crystallization in the skin layer but contributes to increasing the packing of amorphous chains near the skin, which seems to be the controlling factor of the hydrolytic degradation behavior of the fibers.     

Anthocyanins,but not Anthocyanidins,from Bilberry (Vaccinium myrtillus L.) Alleviate Pruritus via Inhibition of Mast Cell Degranulation

Abstract: We have previously reported that bilberry anthocyanins exhibit an anti‐pruritic effect in a mouse model of allergic contact dermatitis. It has been reported that anthocyanins are particularly sensitive to thermal treatment and are easily hydrolyzed to anthocyanidins when exposed to high temperatures. The objective of this study was to compare the anti‐pruritic effect of anthocyanin‐rich quality‐controlled bilberry extract and anthocyanidin‐rich degraded extract using a mouse model of allergic contact dermatitis. BALB/c mice with allergic contact dermatitis induced by 4 weeks of repeated application of 2,4,6‐trinitro‐1‐chlorobenzene (TNCB) were administered Bilberon‐25 orally for 4 weeks after sensitization with TNCB. The effect of Bilberon‐25 on pruritus was evaluated by measurement of scratching behavior. RBL‐2H3 mast cells were used to investigate the effect of Bilberon‐25 on degranulation in 48/80‐stimulated mast cells. Compared with nonheated Bilberon‐25, the proportion of anthocyanins in heated Bilberon‐25 decreased, and the proportion of anthocyanidins was increased in heated‐time dependent manner. Treatment with non‐heated Bilberon‐25 significantly attenuated the TNCB‐induced increase in scratching behavior, whereas treatment with 2 h‐heated Bilberon‐25 did not. Moreover, 300 μg/mL nonheated Bilberon‐25 showed significant inhibition of degranulation in RBL‐2H3 mast cells, whereas 2 h‐heated Bilberon‐25 had no effect at any concentration studied. It is assumed that the inhibitory effect of bilberry anthocyanins on pruritus might be mediated, at least in part, by its inhibitory effect on mast cell degranulation. In conclusion, the anthocyanin‐rich but not anthocyanidin‐rich bilberry extract may be a useful dietary supplement for skin diseases involving pruritic symptoms, such as chronic allergic contact dermatitis, atopic dermatitis, and rhinitis.