Temperature Dependence of the Raman Spectrum in Lithium Oxide Single Crystal

Temperature dependence of the Raman spectrum of lithium oxide single crystal has been measured over a temperature range of 80 to 1073 K. The frequency shift and the line width of the Raman spectrum in lithium oxide were about 531 and 4.5 cm^-1 at 80 K, respectively. At 1073 K, the frequency shift and the line width attained the values of 464 and 112 cm^-1, respectively. The strong temperature dependence of the frequency shift and line width was compared with data from some crystals with a fluorite structure.     

Preparation and characterization of stable dispersions of carbon black and nanodiamond in culture medium for in vitro toxicity assessment

Stable dispersions of carbon black and nanodiamond in culture medium were prepared by adding a pre-mixed dispersion of commercial carbon black or nanodiamond in aqueous bovine serum albumin (BSA) solution to culture medium. Dynamic light scattering revealed that carbon black and nanodiamond dispersions prepared in both NaCl solution and culture medium were highly stable. From DLVO theory and the results of zeta potential measurements, the theoretical effect of the electrostatic interactions between adsorbed BSA molecules was found to be minimal. The asymmetric flow field-flow fractionation measurements revealed that 0.05 or 0.56 mg/mL of BSA molecules were adsorbed on 0.11 or 1.09 mg/mL of carbon black, respectively, indicating 1:2 complexation of BSA with the colloidal particles. In the case of nanodiamond, 0.06 or 0.60 mg/mL of BSA molecules were adsorbed on 0.10 or 1.05 mg/mL of nanodiamond, respectively, indicating 1:2 complexation of BSA, which is the same ratio as in the case of carbon black. The adsorbed BSA molecules served as an effective stabilizing agent for the carbon black and nanodiamond, ensuring dispersion stability for at least 1 week. The preparation of the dispersions can be easily carried out by other researchers for toxicity studies.     

Differential Scanning Calorimetric Study of Solidification Behavior of Monoacylglycerols to Investigate the Cold-Flow Properties of Biodiesel

Monoacylglycerols (MAG) are impurities present in biodiesel as a result of incomplete reactions. MAG often solidify in biodiesel even at room temperature because of their high melting points. This worsens the cold-flow properties such as the cloud point and pour point. We hypothesized that several types of MAG solidify simultaneously; therefore, we performed differential scanning calorimetry of binary mixtures of MAG to elucidate their interactions during solidification. Three thermodynamic formulas were then applied to the experimental results: (1) non-solid-solution, (2) solid-solution, and (3) compound formation models. Binary mixtures of MAG showed complicated liquidus curves with multiple upward convex shapes, with which only the compound formation model fitted well. This model was applied to multicomponent mixtures that consisted of MAG and fatty acid methyl esters (FAME) as surrogate biodiesel fuels. We confirmed that the model still worked well. The results show that the compound formation model has good potential for predicting the cold-flow properties of biodiesel.     

Super environment-friendly electrodeposition paint

Super low VOC due to new composition/reaction mechanism can minimize the environmental risk as it does not contain lead and tin, hazardous air pollutants (HAPs) and endocrine disrupters (EPA/67 items, SPEED’98/JEA/67 items) currently specified as contaminants. New EAD (electrolyzed activate deposition paint) is not the only conventional cure agent or solvent, but also the super low VOC, HAPs materials and endocrine disrupters. The electric energy used by EAD is utilized for the reaction but not for the deposition. EAD consists of two technologies. One is propargyl group change to the allene by using electrodeposition. Propargyl group is stable, but allene group is highly polymerizing. As a result, EAD had high bath stability. The other is sulfonium change to sulfide by using electrodeposition. This sulfonium salt is lost as a result of the electrolytic reduction, and hence can be irreversibly rendered non-conductive. As a result, EAD showed high throwing power.     

Effect of cooking on the antioxidant properties of coloured peppers

Pepper (Capsicum annum L.) has long been recognized as an excellent source of antioxidants, being rich in ascorbic acid and other phytochemicals. This study was conducted to investigate the effect of different cooking methods on the antioxidant properties of coloured peppers. Six varieties of peppers were subjected to different cooking methods, such as microwave heating, stir-frying and boiling in water, for 5 min individually. The cooked and raw peppers were analyzed for radical-scavenging activity (RSA) and total polyphenol content (TP) using 1,1-diphenyl-2-picrylhydrazyl–high-pressure liquid chromatography (DPPH)–HPLC and Folin-Ciocalteu methods, respectively. The samples were also evaluated for ascorbic acid content (AsA) by HPLC. Total carotenoid content was determined spectrophotometrically. Results suggest that there is no significant (P > 0.05) difference in RSA, TP, AsA and total carotenoid contents between the cooked and raw peppers when processed for 5 min. However, the cooked peppers show marked differences (P < 0.05) in the RSA, TP and AsA when cooked for 5 min in boiling water with further reduction observed after boiling for 30 min. This may be due to the leaching of antioxidant compounds from the pepper into the cooking water during the prolonged exposure to water and heat. Therefore, it is vital to use less water and cooking time and also to consume the water used for boiling so as to obtain the optimum benefits of bioactive compounds present in peppers. It is concluded that microwave heating and stir-frying without using water are more suitable cooking methods for pepper, to ensure the maximum retention of antioxidant molecules.     

Influence of alkylpyridine additives in electrolyte solution on the performance of dye-sensitized solar cell

The influence of alkylpyridines additive to an I⁻/I₃⁻ redox electrolyte in acetonitrile on the performance of a bis(tetrabutylammonium)cis-bis(thiocyanato)bis(2,2′-bipyridine-4-carboxylic acid, 4′-carboxylate)ruthenium(II) dye-sensitized TiO₂ solar cell was studied. I–V measurements were performed using more than 30 different alkylpyridines. The alkylpyridine additives showed a significant influence on the performance of the cell. All the additives decreased the short-circuit photocurrent (J_sc), but most of the alkylpyridines increased the open-circuit photovoltage (V_oc) and fill factor (ff) of the solar cell. The results of the molecular orbital calculations suggest that the dipole moment of the alkylpyridine molecules correlate with the J_sc of the cell. These results also suggest that both the size and ionization energy of pyridines correlate with the V_oc of the cell. Under AM 1.5 (100 mW/cm²), the highest solar energy conversion efficiency (η) of 7.6% was achieved by using 2-propylpyridine as an additive, which was more effective than the previously reported additive, 4-t-butylpyridine.     

A Fuzzy Expert System for Damage Assessment Using Genetic Algorithms and Neural Networks

Abstract: An efficient knowledge-acquisition support method is required for improvement and maintenance of the knowledge base in durability evaluation of an RC bridge deck. Such a method is proposed in this paper to automatically acquire fuzzy production rules. This method makes joint use of genetic algorithms and a neural network. Using a neural network as a subsystem, the evaluation function of genetic algorithms can be provided with the weights of the neural network. Introducing a neural network into genetic algorithms, it is possible to acquire new knowledge so that the method is useful when it is difficult to acquire knowledge in the field.     

Pb-free surface-finishing on electronic components’ terminals for Pb-free soldering assembly

Pb-free solderable surface finishing is essential to implement Pb-free solder assembly in order to meet with the growing demand of environmental consciousness to eliminate Pb from electronic products. Two types of widely applicable Pb-free surface finishing technologies are developed. One is the multilayer-system including Pd with Ni undercoat. Heat-resistance of Pd enables whole-surface-plating on to leadframe before IC-assembling process. The other is the double-layer-system with low-melting-point-materials, for example, thicker Sn underlayer and thinner Sn-Bi alloy overlayer, dilutes Sn-Bi alloy’s defects of harmful reactivity along with substrate metal and mechanical brittleness with keeping its advantages of solder-wettability and no whisker.     

Back surface reflectors with periodic textures fabricated by self-ordering process for light trapping in thin-film microcrystalline silicon solar cells

Back surface reflectors (BSRs) with grating structures have been developed to enhance light trapping in thin-film hydrogenated microcrystalline Si (μc-Si:H) solar cells. As a grating structure, a periodic honeycomb-like dimple pattern with a period of ～450 nm has been fabricated on Al substrates by a self-ordering process using anodic oxidation of Al. The clear diffraction effect has been confirmed on the patterned Al from the angle-dependent reflection. From quantum efficiency measurements, we found that the periodically patterned BSR can confine the incident light more effectively than the random textured BSR, especially at longer wavelengths.     

Solving constraint-satisfaction problems by a genetic algorithm adopting viral infection

Several approximate algorithms have been reported to solve large constraint-satisfaction problems (CSPs) within a practical time. While those papers discuss techniques to escape from local optima, this paper describes a method that actively performs global searches. The present method improves the rate of search of genetic algorithms by using viral infection instead of mutation. Partial solutions of a CSP are considered to be viruses, and a population of viruses is created, as well as a population of candidate solutions. The search for a solution is conducted by crossover and infection. Infection substitutes the gene of a virus for the locus decided by the virus. Experimental results using randomly generated CSPs prove that the proposed method is faster that usual genetic algorithms at finding a solution when the constraint density of a CSP is low.