Influence of elevated temperatures on physical and compressive strength properties of concrete containing palm oil fuel ash

The residual compressive strength of concrete containing palm oil fuel ash (POFA) after exposure to elevated temperatures and subsequent cooling was investigated. Specimens from ordinary Portland cement (OPC) and POFA concrete mixes were prepared and subjected to various temperature levels. The POFA concrete contains 20% partial replacement of cement by weight and the temperature levels are; 100, 300, 500 and 800 °C. Two cooling systems which include cooling at room temperature by the natural breeze and water-spray were involved. Compressive strength test was conducted on control specimens as well as concrete specimens revived through the two cooling systems. Physical properties accompanying thermal degradations were also assessed. Residual performance as a ratio of residual strength to original strength was evaluated. The residual performance was found to be higher in POFA concrete than in the normal concrete. In addition, water-cooling was realized to aggravate strength reduction in both normal and POFA concretes when compared with air-cooling. High temperature and cooling system were also found to have great influence on physical properties, such as; mass loss, discolouration and crack patterns.     

Thermal product estimation method for aerodynamics experiments

This paper presents an experimental technique to estimate the appropriate thermal product values of rugged and fast response temperature probes (TPs) for hypersonic aerodynamic experiments. Two types of scratches were used, mainly abrasive papers with different grit sizes and scalpel blades with different thicknesses, to form the probe junction. The effect of the scratch technique on the probe’s thermal product is investigated. The probes are tested and calibrated in the test section and in the end wall of shock tube facility. It is observed that the thermal product of a particular TP depends on the Mach number, junction scratch technique, and junction location, as well as on the enthalpy conditions. It is noted that, depending on the scratch technique, some of the TPs do not require individual calibration; however, calibration for others is likely to be needed.     

Contrast enhancement dynamic histogram equalization for medical image processing application

Image processing requires an excellent image contrast‐enhancement technique to extract useful information invisible to the human or machine vision. Because of the histogram flattening, the widely used conventional histogram equalization image‐enhancing technique suffers from severe brightness changes, rendering it undesirable. Hence, we introduce a contrast‐enhancement dynamic histogram‐equalization algorithm method that generates better output image by preserving the input mean brightness without introducing the unfavorable side effects of checkerboard effect, artefacts, and washed‐out appearance. The first procedure of this technique is; normalizing input histogram and followed by smoothing process. Then, the break point detection process is done to divide the histogram into subhistograms before we can remap the gray level allocation. Lastly, the transformation function of each subhistogram is constructed independently. © 2011 Wiley Periodicals, Inc. Int J Imaging Syst Technol, 21, 280‐289, 2011;     

Fast response surface temperature sensor for hypersonic vehicles1

This paper describes the design, fabrication, and evaluation technique of fast response Surface Temperature Sensor (STS). This STS was made of chromel-constantan elements with 2.2 and 0.8 mm in diameter. The calibration technique using shock tube facility for measuring the transient surface temperature and heat transfer rate is also presented. It has been proved that the STS response time is very short (less than 50 μs), and a rise time in studies of a transient surface temperature is less than 0.5 μs.     

Augmented reality assisted facility layout digitization and planning

Journal of Mechanical Science and Technology - Facility layout planning (FLP) has an important role in manufacturing industries. There are few approaches to solve FLP such as procedural,...     

A new application of giant reed waste material for ammonium removal

Excess nitrogen is one of the main causes of eutrophication in water bodies. In this study, the undesirable agricultural lignocellulosic material giant reed was used to remove ammonium ions from aqueous solutions. Batch experiments were conducted to investigate the effect of various parameters such as contact time, initial ammonium concentration, adsorbent dosage, pH, particle size, agitation rate and phosphate coexisting during the ammonium adsorption process. The ammonium sorption capacity of fibrous giant reed (FGR) at equilibrium was 12.49?mg?N/g with a maximum removal efficiency of 76% observed within 30?min at pH range of 6.5–9.5. Results revealed that the Freundlich isotherm model fitted better with the sorption process than the Langmuir model, and the adsorption process was well described by pseudo-second-order kinetic model. FT-IR analyses indicated that complexation and ion exchange could be the main mechanisms for the ammonium removal by FGR. Results revealed that FGR has a sorption capacity comparable to that of other natural sorbents with the advantage of greater availability with no cost.     

Kinetic study for phosphate removal from water by recycled date-palm wastes as agricultural by-products

The presence of excessive amounts of nutrients including phosphates in water is undesirable. They cause the deterioration of water quality and problems in many natural and engineering systems. The recycling of agricultural waste materials as biosorbents for contaminants removal provides a cheap and ecological means to reduce wastes. This study explored the use of date palm wastes for the effective removal of phosphate from aqueous solutions. Granular date stones (GDS) and palm surface fibres (PSF) as raw abundant waste materials were examined for PO₄ ^-3 removal from aqueous solution. The experimental work was performed in a batch mode to investigate the influence of initial phosphate concentration, contact time, and pH of solution on phosphate biosorption. The FT-IR spectra for the waste materials display many adsorption peaks, confirming the complex nature of the GDS and PSF. Phosphate percentage removal up to 87 and 85% were obtained at initial PO₄ ^-3 concentration of 50 mg as P/L using GDS and PSF, respectively. Due to their low cost and high capability, these types of waste can be used for cost-effective removal of phosphate from wastewater.     

Optimization of the Geometries of Biconical Tapered Fiber Sensors for Monitoring the Early‐Age Curing Temperatures of Concrete Specimens

In this article, a geometrical optimization procedure using biconical tapered fiber sensors is proposed for monitoring the early‐age curing temperatures of concrete specimens. The geometries of the sensors are theoretically optimized by the ray‐tracing theory. The results of the theoretical analysis show that the performance of the sensors is heavily influenced by Evanescent Waves, which are due to the tunneling rays and are fully escaped by tapering the fiber. The effects of the geometrical parameters, including the taper ratios, taper lengths, and ray launch angles, as well as the surrounding temperatures, on the behavior of the sensors are studied numerically. The numerical results demonstrate that higher performance of the proposed optimized sensors can be achieved by a longer taper length and smaller taper ratio combined with an initial ray launching angle of 0.01 rad. An experimental study on early‐age curing temperature monitoring of concrete specimens with the biconical tapered fiber sensors was carried out. The experimental measurements agree well with the theoretical results.     

Exploiting the Plackett–Burman design to examine the formulation effect on curing characteristics of oil palm ash-filled acrylonitrile butadiene rubber compounds

The present paper is focused on exploiting Plackett–Burman design to examine the formulation effect of various chemical components content on the curing characteristics of oil palm ash (OPA)-filled acrylonitrile butadiene rubber (NBR) compound. The filled-NBR compound was prepared by conventional laboratory-sized two roll mill and cured using sulfuric system. Six independent variables such as content of zinc oxide, stearic acid, N-isopropyl-N′-phenyl-p-phenylenediamine, N-cyclohexyl-2-benzothiazole sulfenamide (CBS), sulfur, and even OPA filler were carried out to screen their significant effect on the curing characteristics of NBR compound. The scorch time, optimal cure time, minimum torque, and maximum torque were selected as a response. Results showed that the scorch time and the optimal cure time were significantly affected by CBS, whereas the minimum torque and maximum torque were significantly affected by OPA and sulfur, respectively, within the studied range. Among the chemical components under study, zinc oxide and stearic acid had the least effect on the curing properties of NBR compound. Analysis of variances for all factorial models demonstrated that the model was significant with P value <0.05 while the regularity (R ²) of all models was greater than 0.9. Lastly, the optimal chemical concentrations were predicted to acquire the optimal condition of the curing system for filled-NBR compound.     

Design and analysis of a new magneto rheological damper for washing machine

In this article, a new magneto rheological (MR) sponge damper is proposed for suppression of vibrations in a washing machine. The article presents design optimization of geometric parameters of MR sponge damper (MRSD) using the finite element analysis (FEA) and first order derivative techniques for a washing machine. The article explains the hysteresis behavior and the relationship of damping force with input current for the proposed MRSD. Moreover, the characteristics of the MRSD such as energy dissipation and equivalent damping coefficient are investigated experimentally in terms of input current and excitation amplitude. The passive dampers installed in washing machine are ineffective in reducing unwanted vibrations at resonant frequencies due to real time unbalanced mass. For this purpose, a test setup is established in order to compare the performance of passive dampers with the proposed MRSDs in a washing machine. It is noticed that MRSDs reduce average vibrations of 75.61 % in a low frequency band, whereas in a high frequency band, the MRSDs lessen average vibrations of 30.57 % in a washing machine. In order to determine the performance of proposed design MRSD, a detailed comparison of the performance parameters, such as total damping force, passive force, maximum average vibrations after suppression by MR dampers, maximum current and power ratings is provided with the existing designs of MR damper for washing machine from the literature.