Modeling aviation baggage screening security systems: a case study

Aviation security protects vital national interests, as well as passengers and aircraft. Key components of an aviation security system include baggage and passenger screening devices and operations. Determining how and where to assign (deploy) such devices can be quite challenging. Moreover, even after such systems are in place, it can be difficult to measure their effectiveness. This paper describes how discrete optimization models can be used to address these questions, based on three performance measures that quantify the effectiveness of airport baggage screening security device systems. These models are used to solve for optimal airport baggage screening security device deployments considering the number of passengers on a set of flights who have not been cleared using a security risk assessment system in use by the Federal Aviation Administration (i.e., passengers whose baggage is subjected to screening), the number of flights in this set, and the size of the aircraft for such flights. Several examples are provided to illustrate these results, including an example that uses data available from the Official Airline Guide.     

Search for high-performance probe-fed stacked patches using optimization

High-performance circular probe-fed stacked patch antenna designs are explored through the use of numerical optimization. New trends are sought to aid understanding and to suggest novel solutions. We describe the optimization technique, present a new design trend relating efficiency and bandwidth to the choice of substrate dielectric, and propose and demonstrate a novel, optimized antenna achieving 33% bandwidth whilst maintaining greater than 80% surface wave efficiency.     

Miniaturized coplanar waveguide stop band filters based on multiple tuned split ring resonators

A novel compact stop band filter consisting of a 50 /spl Omega/ coplanar waveguide (CPW) with split ring resonators (SRRs) etched in the back side of the substrate is presented. By aligning SRRs with the slots, a high inductive coupling between line and rings is achieved, with the result of a sharp and narrow rejection band in the vicinity of the resonant frequency of the rings. In order to widen the stop band of the filter, several ring pairs tuned at equally spaced frequencies within the desired gap are cascaded. The frequency response measured in the fabricated prototype device exhibits pronounced slopes at either side of the stop band and near 0 dBs insertion loss outside that band. Since SRR dimensions are much smaller than signal wavelength, the proposed filters are extremely compact and can be used to reject frequency parasitics in CPW structures by simply patterning properly tuned SRRs in the back side metal. Additional advantages are easy fabrication and compatibility with MMIC or PCB technology.     

Object segmentation and labeling by learning from examples

We propose a system that employs low-level image segmentation followed by color and two-dimensional (2-D) shape matching to automatically group those low-level segments into objects based on their similarity to a set of example object templates presented by the user. A hierarchical content tree data structure is used for each database image to store matching combinations of low-level regions as objects. The system automatically initializes the content tree with only "elementary nodes" representing homogeneous low-level regions. The "learning" phase refers to labeling of combinations of low-level regions that have resulted in successful color and/or 2-D shape matches with the example template(s). These combinations are labeled as "object nodes" in the hierarchical content tree. Once learning is performed, the speed of second-time retrieval of learned objects in the database increases significantly. The learning step can be performed off-line provided that example objects are given in the form of user interest profiles. Experimental results are presented to demonstrate the effectiveness of the proposed system with hierarchical content tree representation and learning by color and 2-D shape matching on collections of car and face images.     

On the capacities of bipartite Hamiltonians and unitary gates

We consider interactions as bidirectional channels. We investigate the capacities for interaction Hamiltonians and nonlocal unitary gates to generate entanglement and transmit classical information. We give analytic expressions for the entanglement generating capacity and entanglement-assisted one-way classical communication capacity of interactions, and show that these quantities are additive, so that the asymptotic capacities equal the corresponding 1-shot capacities. We give general bounds on other capacities, discuss some examples, and conclude with some open questions.     

Gamma-irradiation-induced Ag/SiO2 composite films and their optical absorption properties

Small Ag particles or clusters dispersed mesoporous SiO₂ composite films were prepared by a new method: First the matrix SiO₂ films were prepared by sol-gel process combined with the dip-coating technique, then they were soaked in AgNO₃ solutions followed by irradiation of γ-ray at room temperature and in ambient pressure. The structures of these films were examined by X-ray diffraction (XRD), high-resolution transmission electron microscope (HRTEM), and optical absorption spectroscopy. It has been shown that the Ag particles grown within the porous SiO₂ films are very small, and they are isolated and dispersed from each other with very narrow size distributions. With increasing the soaking concentration and an additional annealing, an opposite peakshift effect of the surface plasmon resonance (SPR) was observed in the optical absorption measurements.     

Trajectory control of incompletely restrained parallel-wire-suspended mechanism based on inverse dynamics

This paper discusses parallel wire mechanisms where an end-effector of the mechanism is suspended by multiple wires. The mechanisms enable not only three-dimensional (3-D) positioning but also 3-D orienting of the end-effector, unlike typical wire suspension-type mechanisms such as overhead crane. To discuss the parallel-wire-suspended mechanisms generally, two forms of basic dynamic equations are presented. Then the parallel wire mechanisms are classified into two types based on the basic equations. Dynamical properties of the two types of wire-suspended positioning mechanism are discussed. In this paper, one of the wire-suspended mechanism, incompletely restrained-type parallel wire mechanism, is mainly discussed on its inverse dynamics problem and its trajectory control problem. The inverse dynamics problem for the incompletely restrained-type mechanism plays an important role on its control problem, because the mechanism has low stiffness based on incomplete constraints on the suspended object which is governed by its dynamics. The paper proposes an antisway control method for the suspended object. In the method, the inverse dynamics calculation is used for nonlinear dynamics compensation to control the suspended object of the incompletely restrained parallel wire mechanism.     

The Soft-Contact Method and Instruments for Measuring the Surface Temperature of Solids

A method and instruments based on it are proposed for the contact measurement of surface temperature when carrying out industrial experiments and when monitoring technological parameters.     

Bio-layer management in anaerobic membrane bioreactors for wastewater treatment.

Membrane separation technology represents an alternative way to achieve biomass retention in anaerobic bioreactors for wastewater treatment. Due to high biomass concentrations of anaerobic reactors, cake formation is likely to represent a major cause of flux decline. In the presented research, experiments are performed on the effect of biomass concentration and level of gas sparging on the hydraulic capacity of a submerged anaerobic membrane bioreactor. Both parameters significantly affected the hydraulic capacity, with biomass exerting the most pronounced effect. After 50 days of continuous operation the critical flux remained virtually unchanged, despite an increase in membrane resistance, suggesting that biomass characteristics and hydraulic conditions determine the bio-layer formation rather than the membrane's fouling level. The concept of bio-layer management is introduced to describe the programmed combination of actions performed in order to control the formation of biomass layer over membranes.     

Modeling of a constant Voltage transformer

This paper presents a comprehensive nonlinear model of the controlled constant voltage transformer also known as the ferroresonant transformer. Saturation is a normal mode of operation for this device. This paper derives an equivalent electrical circuit that relates to the physical structure of a typical design. The level of detail includes winding resistances, continuously nonlinear magnetizing inductances, tapped windings, and leakage inductances. The paper describes methods to extract the winding resistances, leakage inductances, and hysteresis loops of the transformer and how to fit the latter into single-valued nonlinear functions. The paper compares computer simulation results of the model with those obtained analytically and experimentally. The results show that the derived circuit will be very useful for designers of the ferroresonant transformer, which is used in uninterruptible power supplies.