无荧光防塌降失水剂KH－931的合成与性能

ＫＨ－９３１是以褐煤、丙烯酰胺、丙烯腈为原料制得的无荧光防塌降失水剂。本文简介了ＫＨ－９３１的合成条件，并对ＫＨ－９３１的防塌作用与降滤失作用进行了室内评定。实验结果表明，ＫＨ－９３１的防塌、降失水效果良好，并具有加量少、无荧光的特点。腐殖酸衍生物，降滤失剂，页岩抑制剂，多功能钻井液处理剂，荧光性，实验室研究     

一维波动方程反演波阻抗的实现及效果

利用波动方程反演波阻抗，由于计算工作量大、稳定性差等原因，一直没有在地震勘探资料处理中得到实际应用。本文提出的一维波方程逐段折叠反演方法能较好地克服上述缺陷，具有计算量相对较小、精度高、稳定性好等特点。并在大庆长垣东部和西部的实际资料处理中见到了良好的效果。     

叠后高分辨率资料处理方法及应用效果

高分辨率勘探是一项系统工程，它由多个环节组成。甚至叠后高发辨率资料处理也是由多个环节组成。本文介绍的叠后高分辨率资料处理流程主要包括Ｌｐ模自适应预测统计反褶积，高频成分补偿，振幅补偿及有色成分校正。文中还就处理流程中各种方法的合理组合，各种方法自身参数的合理选取作了试验和探讨，最后给出了处理实例。     

Micromechanical characterisation of fibre/matrix interfaces

Theoretical analyses for the single fibre pull-out and push-out models under monotonic loading are given which are based on a shear-lag analysis in a fracture mechanics approach considering non-constant friction at the debonded interface as a result of fibre Poisson contraction (or expansion). The solutions allow the determination of typical fibre/matrix interfacial properties such as the interfacial fracture toughness, G_ic, the coefficient of friction, μ, and the residual clamping stress, q₀. Under cyclic loading the interfacial properties are expected to degrade as a result of repetitive abrasion, and a power law function is assumed between μ and the number of elapsed cycles, N. However, G_ic is assumed to be unaffected and a fracture mechanics based debond criterion is derived for the relationship between the external applied stress, the debond length and the reduced friction coefficient for both fibre pull-out and fibre push-out. In addition, the relative displacements between the free fibre end and the matrix top are obtained for cyclic fatigue when the fibre is loaded and unloaded. A relationship obtained for the protrusion (or intrusion) length in fibre pull-out (or push-out) experiments allows the severity of the interface frictional degradation to be evaluated and characterised. Similarities and differences in the frictional degradation behaviour between fibre pull-out and push-out are also identified.     

Microstructure-related fracture toughness and fatigue crack growth behaviour in toughened, anhydride-cured epoxy resins

Fracture toughness and fatigue crack propagation (FCP) of plain and modified anhydride-cured epoxy resin (EP) were studied at ambient temperature. Liquid carboxyl-terminated acrylonitrile-butadiene (CTBN) and silicon (SI) rubber dispersions were used as tougheners for the EP. The morphology of the modified EP was characterized by dynamic mechanical analysis (DMA) and by scanning electron microscopy (SEM). The fracture toughness, K_c, of the compositions decreased with increasing deformation rate. K_c of the EP was slightly improved by CTBN addition and practically unaffected by incorporation of the SI dispersion when tests were performed at low cross-head speed, v. Both modifiers improved K_c at high v, and also the resistance to FCP, by shifting the curves to higher stress intensity factor ranges, ΔK, by comparison with the plain EP. It was established that both fracture and fatigue performance rely on the compliance, J_R, at the rubbery plateau, and thus on the apparent molecular mass between crosslinks, M_c. The failure mechanisms were less dependent upon the loading mode (fracture, fatigue), but differed basically for the various modifiers. Rubber-induced cavitation and shear yielding of the EP were dominant for CTBN, whereas crack bifurcation and branching controlled the cracking in SI-modified EP. The simultaneous use of both modifiers resulted in a synergistic effect for both the fracture toughness at high deformation rate and the FCP behavior.     

PAN共聚纤维的热氧化研究

本工作采用连续式实骏装置与方法,借助力学测试、X射线衍射、元素分析、红外光谱等技术,系统地研究了PAN共聚纤维在连续热氧化过程中化学、结构、性能间的联系,亦对PAN基碳纤维力学性能提高的途径进行了探讨。研究结累表明:在热氧化过程中,PAN共聚体系的热化学反应主要发生在250℃左右;其间纤维的序态结构变化剧烈,易使纤维产生结构缺陷,进而影响热氧化纤维力学性能的变化。     

应用并行技术实现CAD／CAM的高度集成

传统的CAD/CAM系统由于设计思想本身的局限性,其内部只能达到一种松散的基于数据交换的低水平的集成,产品的设计方法也不符合工程技术人员的设计思路。本文提出了基于全耦合的单一数据模型的并行CAD/CAM系统设计思想,使得CAD/CAM系统内部达到以数据共享为基础的高度集成。并行CAD/CAM系统充分体现了工程技术人员的思维方式及产品设计过程的反复性和协调性。此外,文中还提出广义参数化设计的新概念,它与特征设计方法的有机结合保证了产品模型的完整性和产品设计过程的同步性。特征共享是实现CAD和CAM集成的关键因素。并行CAD/CAM系统应用面向对象软件设计思想,实现了复杂数据模型的内部封装,并为数据模型和功能模块之间提供简单直观的界面。面向对象设计方法是开发并行CAD/CAM系统的有效手段。     

蒙特卡洛法速度谱的自动拾取

蒙特卡洛速度谱的自动拾取采用一种非线性优化的快速方法，所得叠加速度的精度可以满足常规地震资料处理中叠加的要求，转换为层速度后可用于叠前深度偏移成象，在给定初始速度模型前提下建立优化目标函数。采用蒙特卡洛非线性优化算法，以最大相似度量准则在考虑实际地质条件前提下给出速度约束条件，对初始速度模型加以扰动，自动寻找速度谱中叠加能量的全局最优解，从而获得合理的速度模型。实际地震资料处理的应用结果表明，自动拾取速度谱比常规的人工速度谱解释工作的效率大幅度提高。在SUN Ultra60机上,仅需1h即可完成2000km的地震资料的速度谱拾取任务，而且所获得的速度模型不受人为因素影响，转换所得的层速度模型用于叠前深度偏移后，获得了满意的成象效果。     

局部施肥对植株生长及根系形态的影响

本文论述了局部施肥对植株地上部与地下部的影响。局部施肥促进了施肥区根系的发达 ,第一侧根与第二侧根较多 ,根的吸收表面积增多 ,根鲜重增加 ,对养分的吸收能力增强 ,但整个根系与地上部的干鲜重下降。     

合山电厂3个机组主厂房定向爆破拆除

介绍了广西合山电厂 1#～3# 机组主厂房定向爆破设计与施工.该工程不仅规模大、环境十分复杂、工期紧、难度高、风险性极强,最大特点是拆除发电设备与爆破同步进行施工.