Shear mode coupling and tilted grain growth of A1N thin films in BAW resonators.

Polycrystalline A1N thin films were deposited by RF reactive magnetron sputtering on Pt(111)/Ti electrode films. The substrates were tilted by an angle ranging from 40 degrees to 70 degrees with respect to the target normal. A low deposition temperature and a high sputter gas pressure were found ideal for tilted growth. The resulting grain tilt angle amounts to about half the substrate tilt angle. For coupling evaluation, 5 GHz solidly mounted resonator structures have been realized. The tilted grain A1N films exhibited a permittivity in the 9.5-10.5 range and loss tangent of 0.3%. Two shear modes as well as the longitudinal mode could be clearly identified. The coupling coefficient k2(eff) of the fundamental thickness shear mode (TS0) was found to be about 0.5%, which is compatible with a c-axis tilt of about 6 degrees.     

Design and Characterization of the CLIMPAQ,Chamber for Laboratory Investigations of Materials,Pollution and Air Quality*

A test chamber has been developed in order to provide a small and simple emission testing facility capable of testing construction products in a climate where the important climatic parameters such as temperature, ventilation rate and air velocity can be varied independently around typical indoor values. The test chamber CLIMPAQ is made of panes of window glass. Other main surface materials are stainless steel and eloxated aluminium. The chamber has a volume of 50.9 litres and is designed to meet the requirements for quantifying air pollution. In this investigation human subjects acted as air pollution judges, and chemical characterization of the air pollution was carried out. Carpet, linoleum, wall paint and seal- ant were tested simultaneously in the CLIMPAQ and in four other chambers ranging from a full-scale chamber of 28 m³ to a field and laboratory emission cell of 3.5· 10^?5m³. Product ranking is the same in all chambers for the sensory measurements. Emission rates based on sensory measurements differ for all products less than 100 % except for tests in a 3-litre chamber where emission rates were higher. Chemical measurements differ up to approximately 10 times for the same product in different chambers. Deviations appear to be the result of different environmental parameters in the various chambers. Low air concentrations or high specific ventilation rates seem to increase emissions, while differences in air velocities and sink properties may also be the cause of differences in emission rates.     

Activated dissociative chemisorption of methane on Ni(100): a direct mechanism under thermal conditions?

The dissociative chemisorption of methane on a Ni(100) single crystal has been studied under thermal conditions as a function of pressure and temperature. The initial sticking coefficient was measured in the pressure range of 0.010–7.0 mbar at temperatures ranging from 375 to 500 K. A strong pressure dependence was observed, consistent with a direct dissociation mechanism under these thermal conditions. This was further confirmed by experiments where the gas at a low pressure was heated by a thermal finger facing the crystal surface. With the thermal finger at the same temperature as the surface, it was possible to ensure that the methane was fully equilibrated to the crystal and an activation energy of 59±1.5 kJ/mol was determined under isothermal conditions.     

Personal Exposure in Displacement Ventilated Rooms

Personal exposure in a displacement ventilated room is examined. The stratified flow and the considerable concentration gradients necessitate an improvement of the widely used fully mixing compartmental approach. The exposure of a seated and a standing person in proportion to the stratification height is examined by means of full-scale measurements. A breathing thermal manikin is used to simulate a person. It is found that the flow in the boundary layer around a person is able to a great extent to entrain and transport air from below the breathing zone. In the case of non-passive, heated contaminant sources, this entrainment improves the indoor air quality. Measurements of exposure due to a passive contaminant source show a significant dependence on the flow field as well as on the contaminant source location. Poor system performance is found in the case of a passive contaminant released in the lower part of the room close to the occupant. A personal exposure model for displacement ventilated rooms is proposed. The model takes the influence of gradients and the human thermal boundary layer into account. Two new quantities describing the interaction between a person and the ventilation are defined.     

The Danish Twin Apartment Study – Part II: Mathematical modeling of the relative strength of sources of indoor air pollution

Abstract This study deals with the modeling of air pollution in apartments from laboratory measurements of source strengths, using formaldehyde and Total Volatile Organic Compounds (TVOCs) as model pollutants. The sources in two test apartments were grouped into two: building-related sources and occupant-related sources. The measured source strengths and ventilation rates were used for the prediction of concentrations expected in the apartments. These predictions were compared to measurements in the apartment over 12 months. The conclusions were that the model predictions based on emission rates measured in the laboratory can be used to predict the long-term concentration of the two model pollutants in the apartments. Considering the measured differences in ventilation between the apartments, an occupant emission rate of between 0.2 and 0.3 mg/h/kg body weight could be estimated. Based on previous suggested limits of acceptable exposures of humans to VOCs, an acceptable average emission rate of VOCs from building materials in general was estimated to be about 30 (μ/m²/h. The modeling showed that during the first 200 days, building materials dominated the emissions. After this, sources relating to the occupants dominated. On average about half of the VOC pollution originated from the building materials.     

Interfacial activity and rate of palladium(II) extraction with decyl pyridine monocarboxylates

Decyl isonicotiniate and decyl nicotiniate permit a rapid extraction of palladium(II) from its hydrochloride solutions. Decyl picoliniate is not a suitable extractant. 4-Octylphenylamine can act as a phase transfer catalyst when its concentration in the organic phase is at least 2·5 × 10^?4 M . It seems that the interfacial adsorption of pyridine carboxylates and of 4-octylphenylamine is not the decisive phenomenon in palladium(II) extraction. The negligible protonation of the pyridine-type extractants and the phase transfer catalysis explains well the quick extraction of palladium(II) with the commercial and highly hydrophobic extractant ACORGA CLX-50.     

A home-page overhaul using other Web sites

The best prototype for designing a new user interface is your old user interface. The second best prototype is a competing product. Your competitors have invested significant resources in designing and implementing what they believe to be good user interfaces. You can glean much of what you need to create a new interface by examining products designed to solve similar problems. As with your own old user interface, you can analyze competing interfaces to see what works and what doesn't. You can also watch how users interact with competing products, and thus learn how they approach tasks. This, in essence, is competitive usability analysis. I recommend performing it very early in the usability engineering life-cycle-after you have visited the customer, gathered requirements, and defined the product vision, but before you design and prototype your new user interface     

Nature-Inspired Meta-Heuristics on Modern GPUs: State of the Art and Brief Survey of Selected Algorithms

Graphic processing units (GPUs) emerged recently as an exciting new hardware environment for a truly parallel implementation and execution of Nature and Bio-inspired Algorithms with excellent price-to-power ratio. In contrast to common multicore CPUs that contain up to tens of independent cores, the GPUs represent a massively parallel single-instruction multiple-data devices that can nowadays reach peak performance of hundreds and thousands of giga floating-point operations per second. Nature and Bio-inspired Algorithms implement parallel optimization strategies in which a single candidate solution, a group of candidate solutions (population), or multiple populations seek for optimal solution or set of solutions of given problem. Genetic algorithms (GA) constitute a family of traditional and very well-known nature-inspired populational meta-heuristic algorithms that have proved its usefulness on a plethora of tasks through the years. Differential evolution (DE) is another efficient populational meta-heuristic algorithm for real-parameter optimization. Particle swarm optimization (PSO) can be seen as nature-inspired multiagent method in which the interaction of simple independent agents yields intelligent collective behavior. Simulated annealing (SA) is global optimization algorithm which combines statistical mechanics and combinatorial optimization with inspiration in metallurgy. This survey provides a brief overview of the latest state-of-the-art research on the design, implementation, and applications of parallel GA, DE, PSO, and SA-based methods on the GPUs.     

Development of high‐definition aqueous polyvinylpyrrolidone photoresists for cathode ray tubes

Aqueous photoresists that are capable of higher resolutions than are currently employed by the cathode ray tube (CRT) industry were developed by combining photoactivators, which activate at shorter UV wavelengths with polyvinylpyrrolidone (PVP). Two photoactivators were synthesized: 4,4′‐diazido‐2,2′‐biphenyl disodium disulfonate (DABP), which has a maximum absorbance at 264 nm, and 4,4′‐diazido‐2,2′‐biphenylethane disodium disulfonate (DABPE), which has a maximum absorbance at 258 nm. The PVP/DABP and PVP/DABPE photoresists successfully imaged a pattern with resolution as small as 4.4 μm with photoactivator concentrations greater than 20% of the PVP concentration. Addition of silane and emulgen greatly improved the performance of the photoresists with more uniform coatings of thicknesses of up to 1.4 μm. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1637–1644, 2006