Energy efficiency optimization of one-way and two-way DF relaying considering circuit power

In this paper, the energy efficiency (EE) of a decode and forward (DF) relay system is studied, where two sources communicate through a half-duplex relay node in one-way and two-way relaying strategies. Both the circuitry power and the transmission power of all nodes are taken into consideration. In addition, three different coding schemes for two-way DF relaying strategy with two phases and two-way DF relaying with three phases are considered. The aim is to maximize the EE of the system for a constant spectral efficiency (SE). For this purpose, the transmission time and the transmission power of each node are optimized. Simulations are used to compare the EE–SE curve of different DF strategies with one-way and two-way amplify and forward (AF) strategies and direct transmission (DT), to find the best energy efficient strategy in different SE conditions. Analytical and simulation results demonstrate that in low SE conditions, DF relaying strategies are more energy efficient compared to that of AF strategies and DT. However, in high SE conditions, the EE of two-way AF relaying and DT strategy outperform some of the DF relaying strategies. In simulations, the impact of different circuitry power and different channel conditions on the EE–SE curves are also investigated.     

A wide frequency range delay line for fast-locking and low power delay-locked-loops

A voltage controlled delay cell with wide frequency range is presented in this paper. The delay-line which is resulted by connecting five series of delay cells generating a wide range of delay from 1.9 to 13.24 ns. It can be used in an analog delay locked loop. The linear characteristic of the circuit with respect to the conventional delay line structures is improved, and a better performance of noise is obtained using differential structure. This circuit is designed by ADS software and TSMC CMOS 0.18 μm technology, with supply voltage 1.8 V. By changing control voltage from 0.335 to 1.8 V in delay line, a wide range of frequency from 75.52 to 917.43 MHz will be covered. Simulation results show that the proposed delay line has power consumption of maximum 3.77 mW at frequency of 75.52 MHz. It also shows that increasing of frequency will reduce power dissipation which is the one of the main characteristics of this novel circuit. Moreover, the delay locked loop which uses these delay cells has a very high lock speed so that the maximum lock time in just five clock cycles.     

Time-Domain Block and Per-Tone Equalization for MIMO–OFDM in Shallow Underwater Acoustic Communication

Shallow underwater acoustic (UWA) channel exhibits rapid temporal variations, extensive multipath spreads, and severe frequency-dependent attenuations. So, high data rate communication with high spectral efficiency in this challenging medium requires efficient system design. Multiple-input multiple-output orthogonal frequency-division multiplexing (MIMO–OFDM) is a promising solution for reliable transmission over highly dispersive channels. In this paper, we study the equalization of shallow UWA channels when a MIMO–OFDM transmission scheme is used. We address simultaneously the long multipath spread and rapid temporal variations of the channel. These features lead to interblock interference (IBI) along with intercarrier interference (ICI), thereby degrading the system performance. We describe the underwater channel using a general basis expansion model (BEM), and propose time-domain block equalization techniques to jointly eliminate the IBI and ICI. The block equalizers are derived based on minimum mean-square error and zero-forcing criteria. We also develop a novel approach to design two time-domain per-tone equalizers, which minimize bit error rate or mean-square error in each subcarrier. We simulate a typical shallow UWA channel to demonstrate the desirable performance of the proposed equalization techniques in Rayleigh and Rician fading channels.     

A Low-Voltage Fully Differential Pure Current Mode Current Operational Amplifier

In this paper a novel high-frequency fully differential pure current mode current operational amplifier (COA) is proposed that is, to the authors’ knowledge, the first pure MOSFET Current Mode Logic (MCML) COA in the world, so far. Doing fully current mode signal processing and avoiding high impedance nodes in the signal path grant the proposed COA such outstanding properties as high current gain, broad bandwidth, and low voltage and low-power consumption. The principle operation of the block is discussed and its outstanding properties are verified by HSPICE simulations using TSMC \(0.18\,\upmu \hbox {m}\) CMOS technology parameters. Pre-layout and Post-layout both plus Monte Carlo simulations are performed under supply voltages of \(\pm 0.75\,\hbox {V}\) to investigate its robust performance at the presence of fabrication non-idealities. The pre-layout plus Monte Carlo results are as; 93 dB current gain, \(8.2\,\hbox {MHz}\,\, f_{-3\,\text {dB}}, 89^{\circ }\) phase margin, 137 dB CMRR, 13 \(\Omega \) input impedance, \(89\,\hbox {M}\Omega \) output impedance and 1.37 mW consumed power. Also post-layout plus Monte Carlo simulation results (that are generally believed to be as reliable and practical as are measuring ones) are extracted that favorably show(in abovementioned order of pre-layout) 88 dB current gain, \(6.9\,\hbox {MHz} f_{-3\text {db}} , 131^{\circ }\) phase margin and 96 dB CMRR, \(22\,\Omega \) input impedance, \(33\,\hbox {M}\Omega \) output impedance and only 1.43 mW consumed power. These results altogether prove both excellent quality and well resistance of the proposed COA against technology and fabrication non-idealities.     

Design of Novel Ultra-Wideband Bandpass Filter with High Selectivity and Wide Stop Band and Optimizing it with Neuro-Genetic Method

This paper develops a novel ultra-wideband bandpass filter with high selectivity, deep stop band and compact size. By linking a broadband bandstop filter at two sides with two feed lines via interdigital coupled lines with enhanced coupling degree, an initial ultra-wideband bandpass filter is created. In this filter, all undesired pass bands are rejected by broadband bandstop filter embedded in middle of ultra-wideband filter. Then, stepped impedance open stubs are used for realizing transmission zeros in pass band edges to increase selectivity. Finally, a neuro-genetic method is applied for optimizing of proposed ultra-wideband bandpass filter. For this task, first a nonlinear relation is established between the input (layout parameters) and output (electrical responses) data by using neural network. Then, genetic algorithm is used in conjunction with neural network model for optimizing the ultra-wideband bandpass filter parameters. The designed filter was fabricated and measured that showed good characteristics including deep stop band and very high pass band selectivity.     

Improved impossible differential and biclique cryptanalysis of HIGHT

HIGHT is a lightweight block cipher introduced in CHES 2006 by Hong et al as a block cipher suitable for low‐resource applications. In this paper, we propose improved impossible differential and biclique attacks on HIGHT block cipher both exploiting the permutation‐based property of the cipher's key schedule algorithm as well as its low diffusion. For impossible differential attack, we found a new 17‐round impossible differential characteristic that enables us to propose a new 27‐round impossible differential attack. The total time complexity of the attack is 2^120.4 where an amount of 2^59.3 chosen plaintext‐ciphertext pairs and 2^107.4 memory are required. We also instantiate a new biclique cryptanalysis of HIGHT, which is based on the new idea of splitting each of the forward and backward keys into 2 parts where the computations associated to each one are performed independently. The time complexity and data complexity of this attack are 2^125.7 and 2⁴², respectively. To the best of our knowledge, this is the fastest biclique attack on full‐round HIGHT.     

Analog to digital converter for high density neural signal recording front-end in 90 nm

High-fidelity recording of neural signals requires varying levels of signal gain to capture low-amplitude single-unit activity in the presence of high-amplitude population activity. A floating-point approach has been used to widen the dynamic range of analog-to-digital converters (ADC) designed for this application. In this paper we present an ADC, designed for multi-channel, portable neural signal recording systems. To achieve low power consumption, small die area and wide dynamic range, an ADC based on a time-based algorithm, combined with a floating-point pipelined structure has been designed and simulated. A conventional variable-gain amplifier (VGA) stage has been eliminated in favor of a reference-current in a time-based ADC architecture. The 12-b pipelined time-based floating-point ADC has been designed with a 7-b mantissa and an exponent that provides an additional 5 bits of dynamic range. The mantissa is determined by a uniform 7-b pipelined time-based analog to digital converter. The ADC chip was designed and simulated in a 90 nm CMOS process, which occupies an active area of 360 μm × 550 μm, and consumes 7.8 μW at 1.2 V in full-scale conversion.     

Highly Conductive Carbon Nanotube‐Graphene Hybrid Yarn

An efficient procedure for the fabrication of highly conductive carbon nanotube/graphene hybrid yarns has been developed. To start, arrays of vertically aligned multi‐walled carbon nanotubes (MWNT) are converted into indefinitely long MWNT sheets by drawing. Graphene flakes are then deposited onto the MWNT sheets by electrospinning to form a composite structure that is transformed into yarn filaments by twisting. The process is scalable for yarn fabrication on an industrial scale. Prepared materials are characterized by electron microscopy, electrical, mechanical, and electrochemical measurements. It is found that the electrical conductivity of the composite MWNT‐graphene yarns is over 900 S/cm. This value is 400% and 1250% higher than electrical conductivity of pristine MWNT yarns or graphene paper, respectively. The increase in conductivity is asssociated with the increase of the density of states near the Fermi level by a factor of 100 and a decrease in the hopping distance by an order of magnitude induced by grapene flakes. It is found also that the MWNT‐graphene yarn has a strong electrochemical response with specific capacitance in excess of 111 Fg^?1. This value is 425% higher than the capacitance of pristine MWNT yarn. Such substantial improvements of key properties of the hybrid material can be associated with the synergy of MWNT and graphene layers in the yarn structure. Prepared hybrid yarns can benefit such applications as high‐performance supercapacitors, batteries, high current capable cables, and artificial muscles.     

Thermal,mechanical, and corrosion resistance properties of vinyl ester/clay nanocomposites for the matrix of carbon fiber‐reinforced composites exposed to electron beam

Vinyl ester/clay nanocomposites with 1, 3, and 5% nanoclay contents were prepared. X‐ray diffractography patterns and Scanning Electron micrographs showed that nanocomposites with the exfoliated structure were formed. Thermogravimetric analysis, water absorption test, and Tafel polarization method, respectively, revealed the improvements in thermal resistance, water barrier properties, and corrosion resistance properties of the samples with an increase in the amount of the incorporated nanoclay. Tensile tests showed that nanoclay also enhanced the mechanical properties of the polymer, so that the tensile strength of the samples with 5% nanoclay was more than 3 times higher than tensile strength of pure vinyl ester samples. Overall, the best properties were observed for the samples containing 5% nanoclay. Pure vinyl ester and nanocomposite with 5% nanoclay content were exposed to the electron beam radiation and their mechanical properties improved up to 500 kGy irradiation dose. Finally, pure vinyl ester and vinyl ester/nanoclay (5%) matrixes were reinforced with carbon fiber and the effect of electron beam irradiation on their mechanical properties was examined. The tensile strength and the modulus of the samples initially increased after exposure to the radiation doses up to 500 kGy and then a decrease was observed as the irradiation dose rose to 1000 kGy. Moreover, nanoclay moderated the effect of the irradiation. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42393.