The impact of cleaner processing on nutrient availability in the bleached kraft industry.

The pulp and paper industry has invested heavily over recent years in cleaner processing, to reduce losses and minimise its impact on the environment. Over the past fifteen years, a New Zealand integrated bleached kraft mill has undergone a comprehensive programme of upgrades to increase production, reduce water consumption and streamline its biological treatment process. Whilst the overall discharge of contaminants from the site decreased, the treatment system performance did not show a concurrent improvement as may have been expected. Reduced BOD removal, low dissolved oxygen levels, and poor solids settlability were symptomatic of phosphorus limitation in the aerated lagoon treatment system. The wastewater entering the system was found to be phosphorus limited at a BOD:P ratio of 100:0.2. Mono-ammonium-phosphate was supplemented, at approximately 30 kg P/d, to raise the phosphorus levels to a BOD:P ratio of 100:0.3. Treatment efficiencies improved very quickly after phosphorus dosage, with a 50% reduction in BOD and TSS discharge, a significant increase in dissolved oxygen levels, and improved BOD removal (85% to 93%). This case study demonstrates that whilst more closed operation can result in reduced discharge of organic loads, there may be negative impacts on the availability of nutrients for balanced biological growth.     

A Study of Integrated Document and Connection Caching in the WWW

Document caching and connection caching are extensively studied problems. In document caching, one has to maintain caches containing documents accessible in a network. In connection caching, one has to maintain a set of open network connections that handle data transfer. Previous work investigated these two problems separately while in practice the problems occur together: In order to load a document, one has to establish a connection between network nodes if the required connection is not already open. In this paper we present the first study that integrates document and connection caching. We first consider a very basic model in which all documents have the same size and the cost of loading a document or establishing a connection is equal to 1. We present deterministic and randomized online algorithms that achieve nearly optimal competitive ratios unless the size of the connection cache is extremely small. We then consider general settings where documents have varying sizes. We investigate a FAULT model in which the loading cost of a document is 1 as well as a BIT model in which the loading cost is equal to the size of the document.     

The concept of an endurance limit for adhesive joints

The effect of cyclic stressing on the strength of single lap adhesive joints has been studied and a considerable reduction in strength observed when the maximum stress exceeds about 40% of the ultimate tensile strength, but whether or not a true endurance limit exists is not proven. Fallacies are shown in some of the techniques which have been proposed for studying the fatigue behaviour of adhesive joints.     

Modeling Power Supply Noise in Delay Testing

Excessive power supply noise during test can cause overkill. This article discusses two models for supply noise in delay testing and their application to test compaction. The proposed noise models avoid complicated power network analysis, making them much faster than existing power noise analysis tools. can cause performance degradation and     

Multistage Zeolite Drying for Energy-Efficient Drying

This work discusses the potential of three multistage zeolite drying systems (counter-, co-, and cross-current) with a varying number of stages. The evaluation showed that for 2-4 stages with heat recovery the efficiency of the systems ranges between 80 and 90%. Additionally, by introducing a compressor, the latent heat in the exhaust air from the regenerator is recovered and used to heat the inlet air for an additional drying stage. As a result, for the counter-current drying system and compressor pressure 1.5-2 bar, a maximum energy efficiency of 120% is achieved, which results in halving the energy consumption compared to conventional drying systems.     

A Radiation Imaging Detector Made by Postprocessing a Standard CMOS Chip

An unpackaged microchip is used as the sensing element in a miniaturized gaseous proportional chamber. This letter reports on the fabrication and performance of a complete radiation imaging detector based on this principle. Our fabrication schemes are based on wafer-scale and chip-scale postprocessing. Compared to hybrid-assembled gaseous detectors, our microsystem shows superior alignment precision and energy resolution, and offers the capability to unambiguously reconstruct 3D radiation tracks on the spot.