Modification of industrial polypropylene film by grafting of poly(acrylic acid)

Grafting of poly(acrylic acid) onto commercial polypropylene films following irradiation by γ-rays was carried out in order to improve their surface properties. The amount of grafting with the irradiation dose was found not to follow the expected linear dependence as it is normally observed for polypropylene films prepared in laboratory amounts. We therefore analyzed the influence of the industrial manufacture process in terms of orientation of the film and addition of antioxidants by determining the peroxide surface density and the extent of grafting therefrom. The unoriented polypropylene film presented the highest peroxide concentration and was thus the most adapated material for successful grafting. Whereas phenol antioxidants limit the peroxide formation and thus must be removed from the film for grafting, the thickness of the chemical modification and can be controlled by means of phosphites. Atomicforce microscopy and wettability measurements showed that the grafted poly(acrylic acid) was heterogeneously distributed on the surface of the film, explaining the observed low reproducibility of the grafting reaction. However, we observed that the polarity of the surface was increased by the grafting. © 1995 John Wiley & Sons, Inc.     

High temperature swelling of coal/tetralin mixtures in a high pressure microdilatometer

High pressure microdilatometer experiments were performed on a subbituminous (Wyodak) and a bituminous (Illinois no. 6) coal in helium and hydrogen atmospheres with and without added tetralin. Wyodak coal samples showed no swelling but contractions ranging between 24 and 40 vol% upon heating at 20 and 100 °C min^{− 1} under helium or hydrogen pressures between 150 and 1000 psig (˜1.0–6.9 MPa). Under the same conditions, Illinois no. 6 coals displayed contractions (25–60 vol%) prior to swelling up to 117 vol%. Upon tetralin addition (at 35–190 wt% of the coal), Wyodak coal samples did not swell but showed an increasing contraction with increasing helium or hydrogen pressure due to a slight softening and fusion of the coal particles. In contrast, addition of tetralin at much lower concentrations (5–35 wt%) had a marked effect on the contraction and swelling behaviour of Illinois no. 6. A maximum swelling of 200 vol% was obtained at a tetralin addition of 30 wt%. The increased swelling results from more extensive softening and fusion of coal particles in the presence of tetralin. Both coals showed a decreasing char yield with increasing tetralin concentration. The substantially lower extent of interaction observed between Wyodak coal samples and tetralin compared to Illinois no. 6 coal can be attributed to the differences in pore structure and/or chemical constitution of the two coal samples. Examination of the resultant solids by optical microscopy revealed the microstructural changes produced by thermal treatment in dilatometer experiments.     

Measuring Software Screen Complexity: Relating Eye Tracking,Emotional Valence,and Subjective Ratings

Enterprise software pages, routinely used to conduct a variety of business-relevant tasks, must be clear and nonconfusing to experienced end users. A study was conducted to consider the impact of several page design factors (background gradient, font, and font size) on perceived ratings of page clarity, completion time, emotional valence (EV) from video, and several eye-tracking parameters. Twenty professional managers each completed 25 tasks on enterprise web pages designed with specific combinations of these factors. Highly rated pages had Tahoma and Larger fonts, compared to Calibri and Smaller fonts. The Gradient background did not influence ratings but did increase the search area and completion time. Although EV was not a sensitive measure across tasks, it was influenced by font differences in the first few seconds of page presentation. Overall, the use of background gradient was not supported, but both Tahoma and Larger fonts were supported for these enterprise pages.     

Light-sensitive elastomers modified by 4-(N-dimethylmaleimido)-benzenesulphenyl chloride

New light-sensitive polymers were prepared by modification of four different elastomers with 4-(N-dimethylmaleimido)-benzenesulphenyl chloride (DMI-BSCI). Polydienes modified by DMI-BSCI form block copolymers. These polymers show a strong increase of the glass transition temperature T_g whereby the T_g increase of modified poly(octenamer) is much smaller. Higher modified polydienes have two T_g. Modified poly(octenamers) show a melting temperature dependence T_m on the content of trans double bonds which is characteristic of statistical copolymers. The ratio of rate constants with which trans- and cis-structures in poly(octenamer) are occupied by DMI-BSCI, is

$\text{k}{}_{\mathrm{trans}}\text{k}{}_{\mathrm{cis}}\text{= 0.34}$

     

The role of the automation development group in analytical research and development at Dupont Merck

Laboratory robotics has been firmly established in many non-QC laboratories as a valuable tool for automating pharmaceutical dosage form analysis. Often a single project or product line is used to justify an initial robot purchase thus introducing robotics to the laboratory for the first time. However, to gain widespread acceptance within the laboratory and to justify further investment in robotics, existing robots must be used to develop analyses for existing manual methods as well as new projects beyond the scope off the original purchase justification. The Automation Development Group in Analytical Research and Development is a team of analysts primarily devoted to developing new methods and adapting existing methods for the robot. This team approach developed the expertise and synergy necessary to significantly expand the contribution of robotics to automation in the authors'' laboratory.     

Dissolution of perfluoroalkyl oligomers in lubricating oil for enhancing wear resistance and fuel economy

Perfluorobutyl-1,1,2-tri-H-1-hexene and perfluoroalkyl methacrylate have been solubilized in lubricating oil by single-step free radically grafting onto poly(ethylene-co-propylene). Perfluoroalkyl-1,1,2,2-tetra-H-ethanol and perfluoropolyether carboxylic acid were solubilized by condensing with poly[(ethylene-co-propylene)-g-glycidyl methacrylate], generating the corresponding perfluoroalkyl ether or ester, respectively. Solubilization of 1,1,2,2-tetra-H-ethanol was also achieved by condensing with poly[(ethylene-co-propylene)-g-2-isocyanoethyl methacrylate] to the corresponding perfluoroalkyl urethane. Scar diameter reductions ranged from 9.4 to 58% using perfluoro-modified graft copolymers as determined using the Four Ball Wear Test, although optimum reductions were obtained using perfluoroalkyl urethane-modified graft copolymers. Moreover, a semiquantitative correlation of scar reductions and thermal instability was determined. Sequence VI engine testing of perfluoroalkyl urethane graft copolymers containing pendant perfluoroalkyl chain lengths of 8.2 and 7.2 had an Equivalent Fuel Economy Index of 4.33 and 4.27, respectively. © 1994 John Wiley & Sons, Inc.     

Lipids ofCrassostrea virginica. I. Preliminary investigations of aldehyde and phosphorous containing lipids in oyster tissue

Oyster tissue contained 2.4% lipid, 0.14 μmole aldehyde per milligram lipid and at least 10 μg phosphorous per milligram lipid. The neutral lipid represented 58%, the glycolipid 6%, and the polar lipid 36% of the total lipid recovered after silicic acid column chromatography. Aldehydes were found in all fractions, but the presence of plasmalogen was verified in only the neutral and polar lipid fractions. At least 68% of the plasmalogen in oyster lipid was found in the polar lipid fraction. At least 13% of the phosphorous in oyster lipids was present as phosphonolipid. The distribution of phosphate and phosphonate lipids was: diacyl phospholipid 38.1%, plasmalogen phospholipid 21.8%, sphingophosphonolipid 13.5%, glyceryl ether phospholipid 8.3%, sphingophospholipid 6.9%, plasmalogen phosphonolipid 6.4%, diacyl phosphonolipid 2.6%, and glyceryl ether phosphonolipid 2.4%. When the per cent of phosphorous as phosphonolipid within the plasmalogen and glyceryl ether classes was calculated, similar values were obtained. These results support the hypothesis that there is a product precursor relationship between these two classes of lipids. Some of the data taken from a thesis to be submitted to the Graduate School, University of Maryland, by Leslye Johnson in partial fulfillment of the requirements for the M.S. degree in biochemistry.     

Hydrogenation of 3,4-epoxy-1-butene over Cu–Pd/SiO2 catalysts prepared by electroless deposition

Electroless deposition has been used to prepare Cu–Pd/SiO₂ bimetallic catalysts wherein initial Cu coverages are limited only to the pre-existing Pd surface. Cu loading on the Pd surface can be systematically varied by modification of deposition kinetic parameters. In this case deposition time was used as the kinetic variable for the preparation of a series of Cu–Pd catalysts. These materials have been characterized using atomic absorption, CO chemisorption, and FT-IR (adsorption of CO), and then evaluated for the hydrogenation of 3,4-epoxy-1-butene, a functionalized olefin having many potential reaction pathways. Catalyst performance and characterization results suggest that Cu is not distributed in a monodisperse manner on the Pd surface, indicating the existence of autocatalytic deposition of Cu on Cu sites. The FT-IR results suggest that although CO adsorption on all sites is suppressed by Cu addition, initial Cu deposition occurs more readily on certain sites. The bimetallic Cu–Pd sites that are formed exhibit unusually high activity for EpB conversion and formation of unsaturated alcohols and aldehydes. This bimetallic effect on catalyst activity and selectivity is best explained, not by the existence of either ligand or ensemble effects, but rather by the bifunctional nature of the Cu–Pd sites present on the surface of these catalysts.     

Chemical Defense in the Plant Bug Lopidea robiniae (Uhler)

Secretions from the metathoracic glands (MTG) of the black locust bug, Lopidea robiniae (Uhler) (Heteroptera: Miridae) contained six major compounds, including (E)-2-hexenal, (E)-2-hexen-1-ol, (E)-2-octenal, (E)-2-octen-1-ol (E)-2-heptenal, and (Z)-3-octen-1-ol. Males and females did not differ significantly in the relative compositions of identified compounds. In feeding trials, six bird species [robin (Turdus migratorious), blue jay (Cyanocitta cristata), brown thrasher (Toxostoma rufum), killdeer (Charadrius vociferus), starling (Sturnus vulgaris), and house wren (Troglodytes aedon)] demonstrated feeding aversions towards L. robiniae, implying that black locust bugs are chemically defended. Bugs discharged the liquid contents of their MTG when attacked, thereby producing a strong and distinct odor. Some birds immediately ejected bugs out of their mouth after biting them, suggesting that the MTG secretion was a deterrent.     

Catalytic Combustion of Model Carbon Particles (CPs) over Pt/β-SiC Catalyst

Platinum catalyst supported on a medium surface area -SiC was successfully used for the catalytic combustion of model carbon particles and compared to a catalyst supported on a low surface area -SiC. The -SiC-based catalyst showed no deactivation as a function of cycling tests while a strong deactivation was observed on the -SiC-based catalyst. This deactivation was attributed to the progressive encapsulation of the platinum particles by a layer of silica which built up during the combustion cycle. These results render possible the use of Pt/-SiC catalyst as a diesel carbon particle catalytic filter with continuous regeneration.