Mechanical characterization of a bituminous mix under quasi-static and high-strain rate loading

There are various methods to determine the compressive and tensile strength of asphalt concrete under static loading conditions and most studies on asphalt strength and fracture have been conducted under such loading conditions. However, pavement materials also have to withstand a wide variety of loading and temperature conditions which may vary from quasi-static to high-strain rate impact, and pavement breakdown may occur due to fracture and/or fatigue failure. In the present study, a bituminous mix with 30% RAP has been characterized under quasi-static (10^?3–10^?4 strain/s) and high-strain rate (200–700 strain/s) regimes. The experimental studies have been performed to better understand the compressive, tensile and fracture response of bituminous mixes. Split Hopkinson pressure bar (SHPB) and its modifications were used for high-strain rate characterization of this bituminous mixture. It was observed that the mechanical properties of the hot mix asphalt (HMA) changed significantly under high-strain rate testing. Also, the failure mechanisms observed under the high-strain rate loading were found to be considerably different from those obtained in static testing, where failure of binder was a predominant mechanism. It was observed that high-strain rate loading caused trans-aggregate failures in the specimens; in addition to failure of the binder.     

Minocycline Loaded Hybrid Composites Nanoparticles for Mesenchymal Stem Cells Differentiation into Osteogenesis

Bone transplants are used to treat fractures and increase new tissue development in bone tissue engineering. Grafting of massive implantations showing slow curing rate and results in cell death for poor vascularization. The potentials of biocomposite scaffolds to mimic extracellular matrix (ECM) and including new biomaterials could produce a better substitute for new bone tissue formation. A purpose of this study is to analyze polycaprolactone/silk fibroin/hyaluronic acid/minocycline hydrochloride (PCL/SF/HA/MH) nanoparticles initiate human mesenchymal stem cells (MSCs) proliferation and differentiation into osteogenesis. Electrospraying technique was used to develop PCL, PCL/SF, PCL/SF/HA and PCL/SF/HA/MH hybrid biocomposite nanoparticles and characterization was analyzed by field emission scanning electron microscope (FESEM), contact angle and Fourier transform infrared spectroscopy (FT-IR). The obtained results proved that the particle diameter and water contact angle obtained around 0.54 ± 0.12 to 3.2 ± 0.18 µm and 43.93 ± 10.8° to 133.1 ± 12.4° respectively. The cell proliferation and cell-nanoparticle interactions analyzed using (3-(4,5-dimethyl thiazol-2-yl)-5-(3-carboxymethoxyphenyl)-2-(4-sulfophenyl)-2H-tetrazolium inner salt) MTS assay (Promega, Madison, WI, USA), FESEM for cell morphology and 5-Chloromethylfluorescein diacetate (CMFDA) dye for imaging live cells. Osteogenic differentiation was proved by expression of osteocalcin, alkaline phosphatase activity (ALP) and mineralization was confirmed by using alizarin red (ARS). The quantity of cells was considerably increased in PCL/SF/HA/MH nanoparticles when compare to all other biocomposite nanoparticles and the cell interaction was observed more on PCL/SF/HA/MH nanoparticles. The electrosprayed PCL/SF/HA/MH biocomposite nanoparticle significantly initiated increased cell proliferation, osteogenic differentiation and mineralization, which provide huge potential for bone tissue engineering.     

Influence of Laser Peening on Phase Transformation and Corrosion Resistance of AISI 321 steel

The objective of this study is to investigate the influence of laser peening without coating (LPwC) on austenitic to martensitic (γ → α′) phase transformation and corrosion behavior of austenitic stainless steel AISI 321 in 3.5% NaCl environment. Results indicate that LPwC induces a large compressive residual stresses of nearly ?854 MPa and γ → α′ phase transformation of about 18% (volume fraction). Microstructures of peened surface confirmed the γ → α′ phase transformation and showed no grain refinement. Hardness increased slightly with a case depth of 900 μm. Despite the smaller surface roughness introduced, corrosion resistance improved after peening due to compressive residual stresses.     

Slope instability analysis in Phyllitic rock in the Lesser Himalayan using three different modeling approach

Bulletin of Engineering Geology and the Environment - The numerical methods for slope stability problems always have a serious concern related to their continuum and discontinuum nature. In...     

Experimental investigation of injection timing on the performance and exhaust emissions of a rubber seed oil blend fuel in constant speed diesel engine

An experimental study is conducted to evaluate the use of rubber seed oil with diesel at a proportion of 20% by volume (RSO20) in a constant speed (1500?rpm) direct injected four-stroke air-cooled single-cylinder compression ignition engine at different injection timings (24°, 27°, 30°, 33° bTDC (before top dead centre)). A series of tests were conducted at various engine load conditions at the rated power of 5.9?kW. The injection pressure was maintained at 200?bar. As a result of investigations, at the full load condition, the brake thermal efficiency of RSO20 at 30° bTDC is high compared with other injection timings and brake energy fuel consumption is increased when advancing injection timing. There is a significant reduction in unburned hydrocarbon emission and carbon monoxide emission, and the oxides of nitrogen emission (NO_x) is increased when advancing the injection timing.     

Enhanced Stretch Formability of Magnesium Alloy Sheet by Prestretching at Various Speeds at Higher Temperature

JOM - Prestretch deformation of 6.48% with various initial speeds (1 mm/min, 101 mm/min, and 100 mm/min) was carried out at 723 K to improve the formability of...     

Microstructure and Mechanical Property Correlation of Mg-Si Alloys

Silicon - The present work aims at understanding the microstructure and mechanical property correlation of hypo (Mg-0.5, 0.7, 1.15 wt% Si) and hyper (Mg-2, 4, 6, 8 and 10 wt% Si) eutectic binary...     

Effect of CoFe2O4 mole percentage on multiferroic and magnetoelectric properties of Na0.5Bi0.5TiO3/CoFe2O4 particulate composites

Na_0.5Bi_0.5TiO₃ (NBT), CoFe₂O₄ (CFO) as well as particulate composites containing different mole percentages of NBT and CFO were synthesized by the solid-state sintering route and characterized for their ferroelectric and ferrimagnetic hysteresis loops, magnetostriction and magnetoelectric (ME) output. The mole% of CFO was found to influence the ferroelectric and ferrimagnetic hysteresis loops as well as magnetostriction and piezomagnetic coefficients which in turn had a significant effect on the magnetoelectric voltage coefficient. The highest magnetoelectric voltage coefficient (α) of 0.5 mV/cm/Oe was recorded in (65) NBT–(35) CFO composite.     

An electrostatic powder spray process for manufacturing thermoplastic composites

Manufacture of thermoplastic composites is expensive because of the difficulty of impregnating the resin into the fibers. Powder processing shows great promise as an impregnation technique for cost-effective manufacturing. This paper discusses an electrostatic powder spray impregnation technique that uses glass fibers. A geodesic fiber spreader is used to spread the fibers locally in the region of maximum powder deposition. A negative corona electrostatic spray gun is employed to charge and direct the powder for coating both sides of the spread fiber tow. The process has been used to impregnate glass fibers with poly(aryl ether ketone ketone) powder. The effect of the powder mass flow, corona voltage, and fiber tow velocity on powder deposition has been investigated. Particle image velocimetry is utilized to determine particle velocities. Compression molded panels have been produced and tested in three point bending.