Oxidative coupling of methane applying a solid oxide fuel cell system

A fuel cell system using yttria-stabilized zirconia as a solid electrolyte was applied to the oxidative coupling of methane. The most active and selective catalyst was BaCO₃ deposited on Au-electrode (anode). Optimum conditions for the reaction were examined. The pressure of methane at the anode and that of oxygen at the cathode should be high as much as possible. The optimum temperature was 1073 K. Several advantages of the method are described.     

Monte Carlo simulation of diffusive-to-ballistic transition in phonon transport

Heat conduction properties in Si nanostructures are analyzed using a Monte Carlo method developed for solving the phonon Boltzmann transport equation. The thermal resistances are evaluated for the systems with various sizes, and the transition from the diffusive to the ballistic heat conduction are investigated. We compare the two different phonon dispersion models (the realistic dispersion relation based on the adiabatic bond charge model and the analytically approximated model), and it is shown that the correct implementation of the phonon dispersion relation is essential to accurately simulate the quasi-ballistic heat conduction properties, which becomes obvious in the structures smaller than the phonon mean free path.     

Experimental study of several types of ground heat exchanger using a steel pile foundation

An experimental study of several types of ground heat exchangers (GHEs) installed in a steel pile foundation, including double-tube, U-tube, and multi-tube GHEs, was carried out at Saga University. Water flows through the heat exchangers and exchanges heat to or from the ground. The performance of GHEs was investigated under actual operation in the cooling mode with flow rates of 2, 4, and 8 l/min. Temperatures of the ground and GHE tube wall were measured to find the temperature distributions according to the depth of the ground and depth of the GHE tube wall. The temperatures of the inlet and outlet of circulated water were also measured to calculate the heat exchange rate. The double-tube had the highest heat exchange rate, followed by the multi-tube and U-tube GHEs. For example, the average heat exchange rate of GHEs over 24 h of continuous operation with a flow rate of 4 l/min was 49.6 W/m for the double-tube, 34.8 W/m for the multi-tube, and 30.4 W/m for the U-tube. An increasing flow rate increased the heat exchange rate of the GHEs. The heat exchange rates increased significantly for flow rate increases from 2 to 4 l/min, but only slightly changed from 4 to 8 l/min.     

折叠之舞

这所住宅位于日本古老的首都--京都中心传统住宅街区内,由建筑师Kentaro Takeguchi+Asako Yamamoto/ALPHAVILLE共同设计建造。由于地区性建筑规范和邻里关系的制约,住宅外部延续了日本传统木制别墅的特征,尽量低调谦和地融入外部传统街区环境之中。当夜暮降临,透过住宅临街的木质格栅散透出柔和的暖光,晕染着这个     

The integral experiment on beryllium with D-T neutrons for verification of tritium breeding

A clean benchmark experiment on beryllium was performed with D-T neutrons at the FNS facility of the Japan Atomic Energy Agency. The main objective was to verify the integral data related to the tritium production on lithium isotopes. Tritium production rates, as well as activation reaction rates were measured inside the beryllium assembly that was shaped as a pseudo-cylindrical slab with an area-equivalent diameter of 628 mm and a thickness of 355 mm. Experimental results were analyzed with a three-dimensional Monte Carlo transport code MCNP-4C and FENDL/MC-2.0, JENDL-3.2/3.3 neutron transport libraries. Evaluation of reaction rates was based on the cross section data taken from the JENDL Dosimetry File and ENDF B-VI data libraries. Analysis shows that all calculation combinations (transport and activation cross section libraries) used for evaluation of reaction rates give data that is agreeable with measured values within 10%.     

Effect of lubricant fluid on plastic metal flow in sliding contact

Plastic metal flow in surface layers, especially “abnormal metal flow”, in which the direction of metal flow in the inner surface layer is different from that in the layer nearer the surface, in sliding contacts between a pin of cemented carbide and a ring of steel under lubrication is discussed in this paper. Low viscosity mineral oil is used as a base oil. Sulphide and chloride extreme pressure additives are also mixed with the base oil. Such a lubricant has a great influence on the plastic metal flow of a ring.While base oil produces severe plastic metal flow, the sulphide additive causes the plastic metal flow to be very mild. In contrast, a lubricant containing a chloride additive causes abnormal metal flow, where cracks can be seen. Conditions for and causes of abnormal metal flow are investigated.     

Combining linguistic resources to create a machine-tractable Japanese-Malay dictionary

We present a method for combining two bilingual dictionaries to make a third, using one language as a pivot. In this case we combine a Japanese-English dictionary with a Malay-English dictionary, to produce a Japanese-Malay dictionary. Our method differs from previous methods in its improved matching through normalization of the pivot language. We have made a prototype dictionary of around 76,000 Japanese-Malay pairs for 50,000 Japanese head words.     

Extraction rice-planted areas by RADARSAT data using neural networks

A classification technique using the neural networks has recently been developed. We apply a neural network of learning vector quantization (LVQ) to classify remote-sensing data, including microwave and optical sensors, for the estimation of a rice-planted area. The method has the capability of nonlinear discrimination, and the classification function is determined by learning. The satellite data were observed before and after planting rice in 1999. Three sets of RADARSAT and one set of SPOT/HRV data were used in Higashi–Hiroshima, Japan. Three RADARSAT images from April to June were used for this study. The LVQ classification was applied the RADARSAT and SPOT to evaluate the estimate of the area of planted-rice. The results show that the true production rate of the rice-planted area estimation of RADASAT by LVQ was approximately 60% compared with that of SPOT by LVQ. It is shown that the present method is much better than the SAR image classification by the maximum likelihood method.