Influence of temperature and permeate recovery on energy consumption of a reverse osmosis system

A model permits analysis of the influence of temperature on permeate recovery and energy consumption. The proposed model is based on the following assumptions: (1) membrane morphology is temperature-independent; (2) membrane rejection and other transport characteristics of membranes are position-independent; (3) specific water permeability of membranes was based on exponential dependence of viscosity vs. temperature; (4) temperature-dependence depembrane rejection is assumed to be linear. This allows for analyzing the influence of channel geometry, feed concentration, flow rate and temperature on permeate recovery and energy consumption. Calculated data are included. The solutionpresented can be segmented andbuilt into systems for comprehensive techno-economic evaluation of the RO-based process where temperature-dependence of process characteristics has to be considered.     

Inertia Effects on the Flow of Bingham Plastics Through Sudden Contractions in a Pipe

The present numerical study concentrates on the effects of moderate and high Reynolds numbers on the laminar flow of a non-Newtonian rigid viscoplastic (Bingham) fluid through a sudden contraction in a pipe. The flow is assumed to be steady, incompressible, and isothermal. Results are presented for a wide range of the governing Reynolds and yield numbers and the significant effects of these two parameters both on the integral and local kinematic properties of the flow field are established. Low yield numbers result in the disappearance of the recirculating flow region at the corner replacing it with a region of very low rates of deformation. The evolution of the centerline velocity in the vicinity of the contraction plane is shown to be independent of the yield number and dependent on the Reynolds number, while the concavities in the streamwise velocity profiles appearing at high Reynolds numbers are independent of the yield number. The pressure losses through the contraction increase with yield number with the effect being more pronounced at lower Reynolds numbers.     

Thermal Evaluation of Diesel/Hydrogen Peroxide Fuel Blend

Thermal properties of fossil fuel are the key fundamental characteristics, which can distinguish any compound as a potential fuel. The performance of diesel fuel blend along with stability and solubility parameter designs are evaluated. The results from the experimental study indicate that the increase in hydrogen peroxide (H₂O₂) amount enhances the cetane number of diesel fuel blend significantly. However, the calorific value decreases as compared to pure diesel fuel. All values performed well according to the ASTM D‐975 diesel testing method. The thermodynamics of the prepared fuel blends also revealed that substantial solubility and diesel/H₂O₂ blend stability are provided even at lower temperatures. Such blends can be used as a feasible replacement of pure diesel fuel.     

Novel composite sandwich structure from green materials: Mechanical,physical, and biological evaluation

Flax and Jute fabrics were used as reinforcements with polyester resin to form composite skins while poplar particleboard was used as a core for making composite sandwich structures by applying vacuum assisted resin transfer molding (VARTM) technique. Mechanical, physical, and biological properties of these novel composite sandwich structures were evaluated. The results showed that the proposed engineered panels have superior mechanical properties that are suitable for different structural applications compared with conventional particleboards. When compared with the control panels, significant enhancement on Modulus of elasticity (MOE) and Modulus of rupture (MOR) were achieved. On the other hand, the results indicated that the proposed panel composites exhibit better dimensional stability compared with poplar particleboard control panels. In addition, the proposed composite sandwich structures proved resistant against the decay fungi after 12 weeks of fungal exposure. Obviously, the developed composite panels could be used in a wide variety of applications. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42253.     

Mechanical properties of gamma‐irradiated styrene‐butadiene rubber/acid‐treated vermiculite clay/maleic anhydride nanocomposites

Nanoparticle vermiculite (VMT) clay was prepared by treatment with hydrochloric acid. Styrene‐butadiene rubber (SBR) nanocomposites were prepared by mixing different contents (2.5, 5, 7.5, and 10 phr) of untreated (VMT) and acid‐treated (DVMT) vermiculite clay, respectively. In addition, different contents (3, 7, and 10 phr) of maleic anhydride (MA) as compatibilizer were mixed via direct melt compounding in internal mixer. The effect of gamma irradiation, VMT clay, and MA contents on the mechanical properties was studied. The acid‐treated VMT clay was characterized by x‐ray diffraction (XRD), transmission electron microscopy (TEM), and Fourier transform infrared (FT‐IR) spectroscopy. Meanwhile, the SBR/VMT composites, SBR/DVMT, and SBR/DVMT/MA nanocomposites were characterized via crosslinking density and tensile mechanical testing and FT‐IR spectroscopic analysis. The results indicated that good yield of nanoparticle vermiculite was achieved when the acid treatment was carried out for 120 h. In addition, the results showed that the presence of DVMT clay improved the chemical bonding in the SBR nanocomposites and hence their mechanical properties. The highest improvement was obtained when the contents of DVMT clay, MA, and irradiation dose were 10 phr, 3 phr, and 100 kGy, respectively. POLYM. ENG. SCI., 59:355–364, 2019. © 2018 Society of Plastics Engineers     

Characterization of Invert Soda Lime Silica Glasses Containing High Titania Content Together with their Glass Ceramics

Silicon - Collective structural, optical and thermal properties were investigated for some prepared soda lime silicate glasses containing high TiO2 contents (35, 40, 45%). X-ray diffraction and...     

Piperidines As Corrosion Inhibitors for Iron in Hydrochloric Acid

The objective of this work is to provide additional insight on the influence of substituents on heterocyclic piperidine as acid corrosion inhibitors for iron. This series include piperidine and six derivatives. The inhibiting properties of piperidine and these derivatives were investigated in 1 M HCl by potentiodynamic polarization (dc) and electrochemical impedance spectroscopy measurements, and inhibition was found to increases as 26dp < 35dp < 2mp < 3mp < pip < 4bp < 4mp. Polarization curves suggest that they can all be considered as mixed-type inhibitors. An attempt to correlate electronic properties of the compounds with their experimental efficiencies using molecular orbital calculation methods did not show any clear-cut relationship.     

Orientation distribution of solids in continuous solid-liquid flow in a vertical tube

During continuous flow of solid-liquid mixtures, the solids may be oriented in a variety of directions relative to the flow axis. The character of the distribution takes on particular importance when materials are processed using electric fields. In this study, solids orientation distributions in continuous, vertical upflow was investigated experimentally combining particle tracking velocimetry. Cylindrical solids showed a more pronounced tendency than cubes to align along the flow direction; this tendency was even greater for elongated cylindrical objects. Solids orientation is influenced by the principal orienting factor (shear flow) and the randomizing factor (orientations of other solids in the mixture). Increasing flow rate tends to drag objects towards their equilibrium (aligned orientation) until they are restricted from further rotation by the presence of other solids. Orientations of cubes were more widely distributed than cylinders, without sharp peaks. The orienting effects of flow rate were also observed for cubes. High solids concentration and larger solids tend to restrict rotation, thus the initial distribution may be maintained through the flow length.     

Improved Approximations for Guarding 1.5-Dimensional Terrains

We present a 4-approximation algorithm for the problem of placing the fewest guards on a 1.5D terrain so that every point of the terrain is seen by at least one guard. This improves on the previous best approximation factor of 5 (see King in Proceedings of the 13th Latin American Symposium on Theoretical Informatics, pp. 629–640, 2006). Unlike most of the previous techniques, our method is based on rounding the linear programming relaxation of the corresponding covering problem. Besides the simplicity of the analysis, which mainly relies on decomposing the constraint matrix of the LP into totally balanced matrices, our algorithm, unlike previous work, generalizes to the weighted and partial versions of the basic problem.