Development of an ultrafast X‐ray computed tomography scanner system: Application for measurement of instantaneous void distribution of gas–liquid two‐phase flow

An ultrafast X‐ray computed tomography (CT) scanner has been developed. This scanner overcomes problems that occur in a transient or unsettled state, which make the conventional CT scanner inappropriate. To reduce the scanning time, this X‐ray CT system uses electronic switching of electron beams for X‐ray generation instead of the mechanical motion adopted by conventional CT scanners. The mechanical motion is a major obstacle to improving scanning speed. A prototype system with a scanning time of 3.6 ms was initially developed and confirmed to measure the dynamic events of two‐phase flow. However, an increased scanning speed is generally required for practical use in the thermal hydraulics research field. Therefore, an advanced type which can operate under the scanning time of 0.5 ms and can measure two‐phase flow with a velocity up to 4 to 5 m/s was developed. © 2000 Scripta Technica, Heat Trans Asian Res, 29(3): 155–165, 2000     

Multistage Stack with Multiple Pore Radii Applying the Temperature Gradient to a Thermoacoustic Engine

Conventional thermoacoustic engines have a stack pore radius that is almost constant in the axial direction. Hence, a thermoacoustic engine is expected to improve the energy conversion efficiency using a multistage stack with multiple pore radii. The stack comprises several bundles of numerous narrow tubes with specified pore radii. The optimum pore radius of the stack is determined by the oscillation frequency and the temperature in the stack. Consequently, the suitable pore radius changes in the axial direction, because the temperature gradient exists along the stack axis. Therefore, a multistage stack with multiple pore radii is introduced, which achieves a desired optimum pore radius everywhere in the stack. The energy conversion efficiency of the multistage stack, which was studied experimentally for a straight-tube type thermoacoustic engine, was compared with that of a conventional single-stage stack. In these experiments, the improvement of the energy conversion efficiency was confirmed. A numerical method with the transmittance matrix to include the effect of a multistage stack was used, and good agreement between experimental and numerical results was obtained. The results make a future possibilities for stack design intended to higher thermoacoustic engine efficiency expect.     

In vivo monitoring of intravenously injected gold nanorods using near-infrared light

Gold nanorods showing surface plasmon (SP) bands in the near-IR region are used as bioimaging probes that respond to near-IR light in mice. The SP bands of intravenously injected polyethylene glycol-modified gold nanorods are directly monitored from the mouse abdomen by using a spectrophotometer equipped with an integrating sphere. The absorbance at 900 nm from the gold nanorods immediately increases after injection and reaches a plateau. The injection of phosphatidylcholine-modified gold nanorods also increases the absorbance at 900 nm, but the absorbance decreases single exponentially with a 1.3-min half-life. In vivo spectral changes of gold nanorods depend on the surface characteristics, and can be observed in real time using simple spectroscopic measurements.     

Preparation and properties of ester or cyano group substituted ring-opening polymers and their hydrogenated derivatives

Ester or cyano substituted tetracyclo [4.4.0.1^2,5.1^7,10]dodec-3-enes (1) were synthesized and their metathesis ring-opening polymerization was examined. The tungsten-based ternary catalyst system polymerized them very well. The polymers showed high glass transition temperatures (T_g) and no evidence of crystallization (e.g., the T_g of the polymer derived from 8-methyl-8-methoxycarbonyl substituted monomer (1a) was 207°C, and colorless transparent films could be casted from the solution of the polymer). The stability of these high T_g polymers were too unstable, so practical thermal molding methods could not be applied to them. The hydrogenation of these polymers with a palladium catalyst decreased T_g and greatly increased thermal stability. The physical and thermal properties of the hydrogenated polymers were thoroughly investigated. Monomer 1 was successfully copolymerized with other cyclic olefins. The resultant copolymers were hydrogenated, giving thermally stable polymers. In all cases examined in this study, a decrease of T_g by hydrogenation was about 35°C, regardless of the monomer structure. These results indicate that the main-chain mobility is the major contribution to the decrease of T_g. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 367–375, 1997     

Characterization of Silicon Carbide–Silicon Nitride Composite Ultrafine Particles Synthesized Using a CO2 Laser by Silicon-29 Magic Angle Spinning NMR and ESR

The structure of silicon carbide–silicon nitride (SiC–Si₃N₄) composite particles synthesized using a CO₂ laser was studied by magic angle spinning nuclear magnetic resonance (MAS-NMR) and electron spin resonance (ESR). The structure around Si atoms changed by introducing N. C atoms around Si were substituted by N atoms, and N-rich configurations around Si atoms increased stepwise as the N content increased. The low N content composite particles consisted of mainly SiC phase containing dissolved N. N atoms were partly present in β-SiC microcrystal and partly in the grain boundary layer in the particle. N atoms were tetrahedrally surrounded by four Si atoms in β-SiC microcrystal and were trivalent state bonded to three Si atoms in the grain boundary layer. The high N content particles consisted of SiC, Si₃N₄, and amorphous phases, whose amount depended on N content.     

Transient analysis of the release and reduction of NOx using a Pt/Ba/Al2O3 catalyst

The release and reduction of NO_x in a NO_x storage-reduction (NSR) catalyst were studied with a transient reaction analysis in the millisecond range, which was made possible by the combination of pulsed injection of gases and time resolved time-of-flight mass spectrometry. After an O₂ pulse and a subsequent NO pulse were injected into a pellet of the Pt/Ba/Al₂O₃ catalyst, the time profiles of several gas products, NO, N₂, NH₃ and H₂O, were obtained as a result of the release and reduction of NO_x caused by H₂ injection. Comparing the time profiles in another analysis, which were obtained using a model catalyst consisting of a flat 5 nmPt/Ba(NO₃)₂/cordierite plate, the release and reduction of NO_x on Pt/Ba/Al₂O₃ catalyst that stored NO_x took the following two steps; in the first step NO molecules were released from Ba and in the second step the released NO was reduced into N₂ by H₂ pulse injection. When this H₂ pulse was injected in a large amount, NO was reduced to NH₃ instead of N₂.

A only small amount of H₂O was detected because of the strong affinity for alumina support. We can analyze the NO_x regeneration process to separate two steps of the NO_x release and reduction by a detailed analysis of the time profiles using a two-step reaction model. From the result of the analysis, it is found that the rate constant for NO_x release increased as temperature increase.     

Corrosion Behavior of Sialon Ceramics in Supercritical Water

The corrosion behavior of sialon ceramics was investigated in supercritical water at 450°C under 45 MPa for 2–50 h. α-sialon exhibited better corrosion resistance than β-sialon and α/β-sialon. Pitting corrosion with the formation of corrosion products was observed in the case of β-sialon and α/β-sialon. By contrast, the corrosion behavior of α-sialon was characterized by uniform corrosion with the formation of corrosion products. The degree of strength deterioration was strongly dependent on the corrosion morphology. The bending strength of α-sialon after corrosion for 30 h was about 90% of its initial strength, while the strength of β-sialon decreased to 65% of its original strength.     

Influences of debonding rate and temperature on tack properties and peel behavior of polyacrylic block copolymer/tackifier system

The influences of debonding rate and temperature on the peel behavior of polyacrylic block copolymer/tackifier system were investigated. Poly(methyl methacrylate)-block-poly(n-butyl acrylate)-block-poly(methyl methacrylate) triblock copolymer (MAM) with hard block contents of 23 (MAM-23) and 16 wt.% (MAM-16) and a 1/1 blend with a diblock copolymer (MA) consisting of the same components (MAM-23/MA, total hard block content of 15 wt.%) were used as the base polymer. A special rosin ester was used as a tackifier at various contents in the block copolymer/tackifier system. The peeling process at the probe/adhesive interface during probe tack testing was observed using a high-speed microscope at 23 °C with debonding rate of 10 mm/s. Three different peeling mechanisms were observed. Type A, where peeling progressed linearly from the edge to the center of the probe without cavitation (MAM-23). Type B, where peeling progressed linearly from the edge to the center of the probe with cavitation (MAM-16). Type C, where cavitation occurred over the entire adhesive layer, and peeling initiation was delayed (MAM-23/MA). The peel behavior of MAM-23 changed from Type A to Type B with a decrease of the debonding rate (1 mm/s) or increase of the temperature (40 °C). In contrast, there was no change for MAM-16 and MAM-23/MA. Cavity formation in an adhesive layer restrains peeling; therefore, it is desirable for improvement of the adhesion strength. The tack properties increased with the tackifier content, and the formation of cavitation was less than that for the systems without the tackifier.     

PCE-based fast path control in multi-domain photonic networks

We discuss issues for controlling an optical path in large-scale photonic networks, and introduce an inter-domain path control system based on Path Computation Elements (PCEs). In the system, maximum flow information enables the load balancing of traffic, and Path Key scheme preserve the confidentiality of internal topology information among carrier networks. Based on the experimental results, we show the path setup in the introduced system is significantly faster than the manual path setup among domains in current carriers' networks. For the additional reduction of the path setup time, we propose the domain-wise paralleled signaling method. We also show that decreasing the number of nodes per domain makes path setup faster in the introduced system with deployment of the proposed signaling method.