Synthesis and characterization of molybdenum disulphide formed from ammonium tetrathiomolybdate

An investigation has been carried out into the possibility of in situ formation of MoS2 within porous anodic films on aluminium, to improve subsequent tribological behaviour, by re-anodizing in thiomolybdate electrolyte. Acidification of thiomolybdate was employed to simulate the conditions for formation of the sulphide at the anodic film/electrolyte interface, followed by appropriate vacuum heat treatments to study possible temperature effects on the sulphide due to either friction or Joule heating during anodizing. The products of both acidification and heat treatment, characterized by X-ray powder diffraction and scanning electron microscopy, were compared with those formed by direct thermal decomposition of ammonium tetrathiomolybdate crystals. The precipitate formed by acidification was mainly amorphous molybdenum trisulphide (MoS3), which on heat treatment at 450 and 850°C yielded 3R-MoS2. 3R-MoS2 also formed by the thermal decomposition of thiomolybdate crystals. Thermogravimetric and differential thermal analyses showed that the decomposition of MoS3 to MoS2 occurred in the range 220–370°C and revealed the sequence of reaction steps. The findings suggest that mainly amorphous MoS3 is formed as a consequence of changes in the pH of the film/electrolyte interface during re-anodizing but the product is relatively easily transformed to crystalline MoS2 on moderate heating which may occur during wear processes.     

A novel method for elimination of line-current harmonics insingle-stage PFC switching regulators

This paper studies a particular single-stage power-factor-correction (PFC) switching regulator employing a discontinuous-conduction-mode (DCM) boost-input cell and a continuous-current-mode (CCM) forward output cell. Although this single-stage PFC regulator can provide a reasonably high power factor when its PFC stage is operating in discontinuous mode, substantial reduction in line-current harmonics is possible by applying a suitable frequency-modulation scheme. This paper derives a frequency-modulation scheme and proposes a practical implementation using a simple translinear analog circuit. A quantitative analysis on the total harmonic distortion (THD) of the line current when the circuit is subject to a limited range of frequency variations is presented along with some considerations for practical design. Experimental data obtained from a prototype confirms the effectiveness of the proposed frequency-modulation scheme. The proposed analog translinear circuit allows custom integrated circuit implementation, making it a viable low-cost solution to the elimination of line-current harmonics in switching regulators     

An empirical study of information technology enabled business process redesign and corporate competitive strategy

Business process redesign (BPR) has been widely touted as a means for leveraging the power of information technology to change business processes radically, resulting in substantial improvements in organizational effectiveness and efficiency. This study represents an early attempt at examining the strategic nature of the phenomenon. Because BPR is radical change and has the ability to alter both the competitive and operational nature of the corporation, it is critical that BPR be coordinated with corporate strategy. Through a survey of information system executives, the relationships between corporate competitive strategy and three types of BPR – intrafunctional, interfunctional and interorganizational – were examined. It was found that organizations following a cost strategy tended to do more BPR projects on interfunctional processes. Furthermore, the positive effect of a cost strategy on interfunctional BPR was found to be strengthened by the degree of integration of IS and business planning. It was also found that while interorganizational BPR was not related to a specific strategy, it was strongly related directly with IS–business planning integration.     

The MiniWiD-Coater. III. Effect of Application Temperature on the Dissolution Profile of Sustained-Release Theophylline Pellets Coated with Eudragit Rs 30 D

Theophylline pellets were coated with Eudragit RS 30 D in a miniature fluid-bed pan coater called MiniWiD developed recently. The dispersions were plasticized with varying amounts of triethyl citrate (TEC), dibutyl phthalate (DBP), and polyethylene glycol 6000 (PEG) and applied at different temperatures ranging from 25 to 45 °C. Theophylline release was tested by dissolution using the USP Apparatus 2 (paddle) in 0.1 N hydrochloric acid under sink conditions over 6 hours.

At a coating level of 4 % (0.7 mg/cm²) sustained-release profiles were obtained from dispersions plasticized with TEC or DBP. By reducing the amount of plasticizer from 20 to 10%, films with higher permeabilities were obtained. This effect was compensated by tempering the pellets at 50 deg;C for 24 hours. The coating temperature had little effect on the dissolution profiles of TEC-plasticized films and no effect on films with DBP.

Coatings plasticized with 20% PEG were applied at temperatures ranging from 25 to 45 °C. These films required a coating level of about 18 % (3.3 mg/cm²) to provide comparable sustained-release properties. In contrast to DBP and TEC, a strong influence of the coating temperature on the release rates was observed in which higher temperatures led to slower release rates. This behavior can be explained by the minimum film-forming temperature (MFT). Since PEG does not lower the MFT of Eudragit RS 30 D, the application of these films below the MFT of 45 °C is associated with a lower degree of film formation.     

A practical controller for explicit rate congestion control

This paper examines congestion control for explicit rate data networks. The available bit rate (ABR) service category of asynchronous transfer mode (ATM) networks serves as an example system, however, the results of this paper are applicable to other explicit rate systems as well. After a plant model is established, an adaptive control strategy is presented. Several algorithm enhancements are then introduced. These enhancements reduce convergence time, improve queue depth management, and reduce parameter bias. This work differentiates itself from the other contributions in the area of rate-based congestion control in its balanced approach of retaining enough complexity as to afford attractive performance properties, but not so much complexity as to make implementation prohibitively expensive     

Creating and Justifying Research and Development Value: Scope,Scale, Skill and Social Networking of R&D

In this paper we describe a framework for analysing the creation and justification of Research & Development. The 4S framework is developed for analysing the scope, scale, skills and social network aspects of Research & Development value. The framework is based on social system theory, a process contingency model, and recent Research & Development metrics. We present a first empirical assessment based on a workshop using the 4S framework for leveraging Research & Development. Results that assist in the assessment of value creation utilising R & D within networks are very relevant in high tech industries. The multi–dimensional process approach of this framework seems promising for understanding and managing R&D value creation, but needs further operationalisation. Case studies are described and a Dutch network on leveraging R&D has been initiated.