SiC颗粒尺寸及含量对SiCp／2024Al复合材料性能的影响

本文对粉末冶金法制备的SiCp/2024Al复合材料的性能进行了研究。随SiC颗粒尺寸的增大,复合材料的强度降低,而塑性和磨损抗力则增加。SiC颗粒尺寸对复合材料的物理性能没有什么影响。增加SiC颗粒含量,复合材料的强度、模量均增大,磨损抗力亦明显增加,而塑性和热膨胀系数则降低。     

Pultruded fibre reinforced polyurethane composites II. Effect of processing parameters on mechanical and thermal properties

This paper presents a novel process for the fabrication of pultruded polyurethane (PU) composites. The effects of the processing parameters on the mechanical properties (flexural strength and flexural modulus, etc.) and thermal properties (HDT) of the fibre reinforced PU composites by pultrusion have been studied. The processing parameters investigated include pulling rate (in-line speed), die temperature, filler type and content, and post-cure time and temperature. Results show that the composites possessed various optimum pulling rates at different die temperatures. On the basis of the DSC diagram, the swelling ratio, the mechanical properties and the thermal properties of composites, the optimum die temperature can be determined. It is found that the mechanical and thermal properties increase with filler content for various types of filler. The mechanical and thermal properties increase at a suitable post-cure temperature and time. Furthermore, the properties which decreased due to the degradation of composite materials for a long post-cure time will be discussed.     

液化气球罐焊缝H2S应力腐蚀裂纹的返修补焊

对宁夏炼油厂一台200m3低合金钢球罐H2S应力腐蚀裂纹采用气刨打磨后补焊的返修方法表明，碳弧气刨时的骤热不会使裂纹向纵深扩展，只是必须在补焊前将返修部位焊缝两侧各100mm范围内打磨至完全露出金属光泽，以便彻底消除裂纹源，避免补焊时再产生新的微小裂纹。若返修深度不大于罐壁厚度的二分之一，则不必进行射线探伤检查，只须进行100％的超声波检查，在水压试验前后对返修部位进行100％磁粉探伤则是非常必要的。     

计算机轧辊管理软件

使用计算机管理轧辊可以非常方便地查询每一条轧辊的材质、产地、车削情况使用情况及该辊的轧制产量等数据，并可根据要求打印表格或轧辊消耗报表。     

环境放射化学研究中几个问题的讨论

本文从辐射环境保护和公众辐射防护的角度，讨论了放射性核素在环境中的迁移行为，放射性核素与环境介质的相互作用和放射性核素在环境中的形态等涉及到环境放射化学研究方向的问题，并讨论了它们之间相互依存的关系。     

Up-regulation of CIR1/CROC1 expression upon cell immortalization and in tumor-derived human cell lines

Inactivation of 5-HT1A and [3H]5-HT binding sites by N-Ethoxycarbonyl-2-ethoxy-1, 2-dihydroquinoline (EEDQ) was studied in regions of rat brain. After exposure to EEDQ (4 mg/kg body wt.) for 7 days, it is observed that the density of 5-HT1 receptor sites was decreased by nearly 20% in both cortex and hippocampus. The decrease, however, in 5-HT1A sites was more significant (70%) in both the regions. The affinity of [3H]5-HT to 5-HT1 sites was decreased significantly in both cortex and hippocampus after exposure to EEDQ, without affecting the Kd of 5-HT1A sites. Displacement studies suggested that EEDQ has high affinity to 5-HT1 sites with a Ki of 42.9+/-2.4 nM. After exposure neither basal nor 5-HT stimulated adenylyl cyclase activity was changed in cortex. The results of this study suggest that EEDQ decreases the density of 5-HT1 and 5-HT1A receptor sites but does not cause functional downregulation of these sites in rat brain.     

激光在大型望远镜中应用

简述激光在大型天文望远镜中应用，如激光人造星，测量４．３ｍ主镜面形，自准调校恒星光干涉仪和程差补偿测量，望远镜筒主副镜间相对倾角和弯沉测量等。     

Compressive and tribological properties of Al2O3 fibre and hexagonal BN particle hybrid reinforced Al-Si alloys

Al₂O₃ fibre-hexagonal BN particle hybrid reinforced aluminium-silicon alloys were fabricated by centrifugal force infiltration route. Hardness test and ultimate compressive test results are reported. The wear and friction properties of hybrid MMCs was investigated by means of a block-on-ring (bearing steel) type wear rig in a dry sliding condition. It is shown that the hardness and ultimate compressive strength of hybrid MMCs was evidently decreased with the addition of hexagonal BN particles, however, the wear rate and coefficient of friction of hybrid MMCs was improved simultaneously with increase of BN particle volume fraction, especially for the higher applied loads in the test.     

含碳酸盐萤石矿石全弱酸性浮选新工艺

对含碳酸盐较高的萤石矿石提出了不加纯碱的全弱酸性浮选新工艺,获得CaF_298.21％、SiO_20.67％,回收率为93.25％的良好指标,实现了低模数碳酸盐—萤石矿石的高纯分离。