Copper containing 6000-series aluminium alloys may become susceptible to intergranular corrosion (IGC) as a result of improper thermomechanical processing. Effect of cooling rate after solution heat treatment on the corrosion behaviour of a model AlMgSi(Cu) alloy of nominal composition (wt%) 0.6 Mg, 0.6 Si, 0.2 Fe, 0.2 Mn and 0.1 Cu was investigated. Slow cooling rates were simulated by isothermal treatment for predetermined times in lower temperature baths immediately after solution heat treatment. Treatment for 10-100 s at temperatures below 400 °C introduced susceptibility to IGC. Longer heat treatment at the same temperatures introduced susceptibility to pitting. A corrosion resistant time zone was found between the zones of IGC and pitting at temperatures lower than 350 °C. Quenching in water after solution heat treatment prevented IGC. IGC was related to microgalvanic coupling between the noble Q-phase (Al4Mg8Si7Cu2) grain boundary precipitates and the adjacent depleted zone. Pitting was attributed to coarse particles in the matrix. Possible mechanisms causing the corrosion resistant intermediate zone are discussed. The results indicate possible methods for obtaining increased corrosion resistance of similar alloys by proper thermal processing. 相似文献
Deformation due to two different surface-machining conditions—grinding (126 μm diamond) and polishing (3 μm diamond)—in an uniaxial hot-pressed Al2O3–30%-SiC-whisker composite has been investigated. A Warren–Averbach analysis of grazing incidence X-ray diffractometry data shows that the deformation is localized to the very top surface zone. The cell size and the root mean square of the strain show a gradient in the deformed layer. Transmission electron microscopy studies, in cross-sectional view, also show a near-surface deformation zone containing dislocations, twins, and cracks. This is seen for both machining procedures, but the depth of the zone and the degree of deformation, in terms of dislocation density and number of cracks, is much higher in the roughly ground specimen than in the polished one. For comparison, a monolithic Al2O3 sample also has been studied after grinding. The deformation zone is very similar to the Al2O3–SiC sample with the same grinding condition, but cracks and dislocations are present at a slightly larger depth. The deformation depth for the polished Al2O3–SiC sample is ∼50 nm. In the ground Al2O3–SiC sample, the deformation depth is 1–1.5 μm and corresponds to the grain size. The deformation zone in the ground monolithic Al2O3 sample is 1.5–2 μm deep. The observed grain-boundary cracks are almost parallel to the surface and may originate from nonaccommodated plastic flow between grains. 相似文献
This paper introduces the notion of manipulability to mobile, multi-agent networks as a tool to analyze the instantaneous effectiveness of injecting control inputs at certain, so-called leader nodes in the network. Effectiveness is interpreted to characterize how the movements of the leader nodes translate into responses among the remaining follower nodes. This notion of effectiveness is a function of the interaction topologies, the agent configurations, and the particular choice of inputs used to influence the network. In fact, classic manipulability is an index used in robotics to analyze the singularity and efficiency of configurations of robot-arm manipulators. To define similar notions for leader–follower networks, we use a rigid-link approximation of the follower dynamics and, under this assumption, we prove that the instantaneous follower velocities can be uniquely determined from that of the leaders’, which allows us to define a meaningful and computable manipulability index for the leader–follower networks. This paper examines the property of the proposed index in simulation and with real mobile robots, and demonstrates how the index can be used to find effective interaction topologies. 相似文献
In this investigation, a comparative study for a NOX storage catalytic system was performed focusing on the parameters that affect the reduction by using different reductants (H2, CO, C3H6 and C3H8) and different temperatures (350, 250 and 150 °C), for a Pt/BaO/Al2O3 catalyst. Transient experiments show that H2 and CO are highly efficient reductants compared to C3H6 which is somewhat less efficient. H2 shows a significant reduction effect at relatively low temperature (150 °C) but with a low storage capacity. We find that C3H8 does not show any NOX reduction ability for NOX stored in Pt/BaO/Al2O3 at any of the temperatures. The formation of ammonia and nitrous oxide is also discussed.
Transient experiments were performed to study sulfur deactivation and regeneration of Pt/BaO/Al2O3 and Pt/SrO/Al2O3 NOx storage catalysts. It was found that the strontium-based catalysts are more easily regenerated than the barium-based catalysts
and that a higher fraction of the NOx storage sites are regenerated when H2 is used in combination with CO2 compared to H2 only. 相似文献
Given a collection of parameterized multi-robot controllers associated with individual behaviors designed for particular
tasks, this paper considers the problem of how to sequence and instantiate the behaviors for the purpose of completing a
more complex, overarching mission. In addition, uncertainties about the environment or even the mission specifications
may require the robots to learn, in a cooperative manner, how best to sequence the behaviors. In this paper, we approach this
problem by using reinforcement learning to approximate the solution to the computationally intractable sequencing problem,
combined with an online gradient descent approach to selecting the individual behavior parameters, while the transitions
among behaviors are triggered automatically when the behaviors have reached a desired performance level relative to a task
performance cost. To illustrate the effectiveness of the proposed method, it is implemented on a team of differential-drive
robots for solving two different missions, namely, convoy protection and object manipulation. 相似文献
The effect of artificial aging parameters on the corrosion performance of air cooled AlMgSi(Cu) model alloy extrusions was investigated. Accelerated corrosion test revealed that the extrusions were highly susceptible to intergranular corrosion (IGC) in the naturally aged condition. However, IGC susceptibility was reduced, and finally eliminated, by artificial aging. Overaging introduced slight pitting susceptibility. EDS X-ray mapping in FE-TEM revealed Mg2Si and Q-phase (Al4Cu2Mg8Si7) grain boundary precipitates and a continuous Cu-enriched grain boundary film. IGC susceptibility was related to the Cu-enriched grain boundary film. Increased IGC resistance was caused by coarsening of the grain boundary film by aging. Pitting susceptibility by over aging evolved due to coarsening of the Q-phase particles in the grain bodies. 相似文献
This paper reports on the use of qualitative analysis to inform a risk analysis framework for decentralised water systems. To realise the benefits from these technologies, a methodology is applied to learn from previous difficulties in implementing and managing them. A workshop process was used to capture stories from industry professionals on difficulties they have encountered in planning and implementation. Qualitative analysis of story narratives revealed stages where there was some type of development process failure; as well as failure modes and factors influencing the difficulties encountered. The analysis also generated insights: difficulties in one part of the development process tends to propagate to subsequent stages; system difficulties most often occurred in the policy stage of development due to institutional inertia and lack of adaptive governance; and the best indicator of problems with a decentralised system was complaints of poor water quality. Furthermore, this paper also provides a method to learn from past difficulties by identifying what data needs to be collected in order to populate a risk model which can be used for improving risk assessment of the development process for decentralised systems. This can provide a basis for better decision making, policy and guidelines; an important factor in mainstream acceptance. 相似文献
Electrostatic probes or Langmuir probes are the most common diagnostic tools in plasma discharges. The second derivative of the Langmuir probe I-V characteristic is proportional to the electron energy distribution function. Determining the second derivative accurately requires some method of noise suppression. We compare the Savitzky-Golay filter, the Gaussian filter, and polynomial fitting to the Blackman filter for digitally smoothing simulated and measured I-V characteristics. We find that the Blackman filter achieves the most smoothing with minimal distortion for noisy data. 相似文献