General properties of antennas

In antenna design there are some fundamental relationships based on reciprocity. The equivalence of antenna pattern in transmission and reception is well known. Less well known is the time-derivative relationship going from reception to transmission. These relationships are derived here and expressed in various useful forms. Electric and magnetic dipoles are given special consideration, and the combined form constructed as a terminated TEM transmission line (the BTW antenna) is discussed for its transmission and reception properties     

Evaluation of a compound probability model with tower-mountedscatterometer data

Six months of data from the YSCAT94 experiment conducted at the CCIW WAVES research platform on Lake Ontario, Canada, are analyzed to evaluate a compound probability model. YSCAT was an ultrawideband small footprint (≈1 m) microwave scatterometer that operated at frequencies of 2-18 GHz, incidence angles from 0° to 60°, both h-pol and v-pol, and which tracked the wind using simultaneous weather measurements. The probability distribution function of the measured instantaneous backscattered amplitude (p(a)) is compared to theoretical distributions developed from-the composite model and a simple wave spectrum. Model parameters of the resulting Rayleigh/generalized lognormal distribution probability density function (pdf) (C, a₁ , and a₂) are derived directly from the data and are found to demonstrate relationships with wind speed, incidence angle, and radar frequency     

High-frequency small signal AC and noise modeling of MOSFETs for RFIC design

High-frequency (HF) AC and noise modeling of MOSFETs for radio frequency (RF) integrated circuit (IC) design is discussed. A subcircuit RF model incorporating the HF effects of parasitics is presented. This model is compared with the measured data for both y parameter and f_T characteristics. Good model accuracy is achieved against measurements for a 0.25 μm RF CMOS technology. The HF noise predictivity of the model is also examined with measured data. Furthermore, a methodology to extract the channel thermal noise of MOSFETs from HF noise measurements is presented. By using the extracted channel thermal noise, any thermal noise models can be verified directly. Several noise models including the RF model discussed in this paper have been examined, and the results show that the RF model can predict the channel thermal noise better than the other models     

Capacity-achieving sequences for the erasure channel

This paper starts a systematic study of capacity-achieving (c.a.) sequences of low-density parity-check codes for the erasure channel. We introduce a class A of analytic functions and develop a procedure to obtain degree distributions for the codes. We show various properties of this class which help us to construct new distributions from old ones. We then study certain types of capacity-achieving sequences and introduce new measures for their optimality. For instance, it turns out that the right-regular sequence is c.a. in a much stronger sense than, e.g., the Tornado sequence. This also explains why numerical optimization techniques tend to favor graphs with only one degree of check nodes.     

Fabrication of 1.55 μm VCSELs on Si using metallic bonding

Using AuGeNiCr multilayered metals as the wafer bonding medium, long-wavelength GaInAsP/InP vertical cavity surface emitting lasers employing Al-oxide/Si as the upper and lower distributed Bragg reflectors were fabricated on Si substrate with the bonding interface formed outside the vertical cavity surface emitting laser cavity. Laser emission at 1.545 μm was measured under pulsed operations near room temperature. The low-temperature metallic bonding process demonstrates a great potential in device fabrication     

Retrievals of column water vapor using millimeter-wave radiometric measurements

The airborne Millimeter-wave Imaging Radiometer (MIR) measurements conducted over the Midwest region of the continental United States during January/February 1997 and over the Alaska-Arctic region during May 1998 are used to estimate column water vapor W<0.8 g/cm/sup 2/ under a clear sky. On board the same aircraft are two other instruments, the Cloud Lidar System (CLS) and MODerate-resolution Imaging Spectrometer (MODIS) Airborne Simulator (MAS), which provide cloud cover information and independent measurements of W, respectively. The MIR-estimated W values are compared and found to be in very good agreement with those measured by rawinsondes at near concurrence. A close correlation is found between the MIR-estimated W and that estimated from the MAS near-IR reflectance ratios. Water surface emissivities at several MIR frequencies are obtained in the process of the W retrieval from several flights over the Midwest lakes. These estimated emissivities compared favorably with values calculated for a calm water surface, which are based on a di-electric permittivity model and MAS-measured surface temperatures. The results from all comparisons strongly demonstrate the soundness of the technique for estimating W.     

Electromigration-induced damage in bamboo Al interconnects

Depletion and hillock formation were examined in-situ in a scanning electron microscope (SEM) during electromigration of bamboo Al interconnect segments. Hillocks formed directly at the anode ends of the segments by epitaxial addition of Al at the bottom Al/TiN interface. Depletion occurred nonuniformly from the cathode end and stopped once the distance between the leading void and the hillock reached the critical length for electromigration at the given current density. A modified equation for the drift velocity is proposed, which includes the effect of nonuniform depletion and predicts that interconnects with nonuniform depletion are more reliable than those with uniform depletion.     

Test Case Generation as an AI Planning Problem

While Artificial Intelligence techniques have been applied to a variety of software engineering applications, the area of automated software testing remains largely unexplored. Yet, test cases for certain types of systems (e.g., those with command language interfaces and transaction based systems) are similar to plans. We have exploited this similarity by constructing an automated test case generator with an AI planning system at its core. We compared the functionality and output of two systems, one based on Software Engineering techniques and the other on planning, for a real application: the StorageTek robot tape library command language. From this, we showed that AI planning is a viable technique for test case generation and that the two approaches are complementary in their capabilities.