Fractoemission from Lead Zirconate-Titanate

We present measurements of the electron, positive ion, and photon emission accompanying the fracture in vacuum of poly-crystalline 95/5 lead zirconate-titanate. The intensities of the charged-particle components of this fractoemission are shown to depend strongly on the direction (relative to the direction of fracture) and magnitude of polarization. The most intense emission is observed when the fracture surfaces are perpendicular to the polarization direction. The emission intensity increases monotonically with polarization. These results are interpreted in terms of a model involving charge separation on the fracture surfaces leading to a microdischarge during fracture. Implications to the interpretation of triboluminesence effects are discussed.     

Effect of grain boundaries on isothermal solidification during transient liquid phase brazing

The influence of liquid penetration at grain boundary regions on the rate of advance of the solid-liquid interface during isothermal solidification of transient liquid phase (TLP) brazed nickel joints has been examined. The test samples used in this study were Ohno-cast nickel with a grain size of >4 mm and a fine-grained nickel with a grain size of around 40 μm. Both Ni-base materials had the same chemical composition. The rate of isothermal solidification was greater when fine-grained nickel was employed during TLP brazing using Ni-11 wt pct P filler metal at 1200 °C. Liquid penetration at grain boundaries accelerates the isothermal solidification process by increasing the effective solid-liquid interfacial area and increasing the rate of solute diffusion into the base material. An analysis of electron channeling patterns has confirmed that random high-angle boundaries have a greater influence on the rate of isothermal solidification than ordered boundaries including small-angle or twin boundaries. Formerly Visiting Scientist, Department of Metallurgy and Materials Science, University of Toronto. Formerly Postdoctoral Fellow, Department of Metallurgy and Materials Science, University of Toronto     

Biodegradable hollow microfibres to produce bioactive scaffolds

Biodegradable hollow microfibres containing particles loaded with specific active agents can be potentially employed to produce a special kind of substrate for tissue engineering, able to function as a scaffold and at the same time to act as a drug‐releasing system. Biodegradable hollow microfibres based on poly(lactic acid) were produced by a dry–wet spinning procedure. Drug‐loaded microparticles were prepared by a simple oil‐in‐water emulsion and entrapped inside the fibres. The morphology of both fibres and particles was investigated by scanning electron microscopy. The mechanical and thermal properties of the fibres were investigated by tensile tests and differential scanning calorimetry. In vitro tests were performed to evaluate the release of the drug from the fibres loaded with the particles Copyright © 2004 Society of Chemical Industry     

Optical properties of doped bismuth telluride crystals in the region of plasma effects

The optical properties of bismuth telluride crystals doped with donor-and acceptor-type impurities are studied. The fact that energy corresponding to the resonance frequency of plasma oscillations of free charge carriers (plasmons) approaches the band-gap energy is detected in the infrared spectral region, where the main elementary excitations in the electronic system of these materials are observed. The mentioned approach of energies varies the intensity of electron-plasmon interaction, which affects the recombination processes in the materials widely used for the fabrication of thermoelectric energy converters.     

Evaluating software reuse alternatives: a model and its application to an industrial case study

We propose a model that enables software developers to systematically evaluate and compare all possible alternative reuse scenarios. The model supports the clear identification of the basic operations involved and associates a cost component with each basic operation in a focused and precise way. The model is a practical tool that assists developers to weigh and evaluate different reuse scenarios, based on accumulated organizational data, and then to decide which option to select in a given situation. The model is currently being used at six different companies for cost-benefit analysis of alternative reuse scenarios; we give a case study that illustrates how it has been used in practice.     

Effect of broaching on high-temperature fatigue behavior in notched specimens of INCONEL 718

Notches were machined in specimens of INCONEL 718 by a broaching process, where differing broaching runs led to differing extents of subsurface deformation and surface roughness. Fatigue tests were carried out at 600 °C with a trapezoidal loading waveform at 0.25 Hz. The broaching process that led to the more severe subsurface deformation (but lower surface roughness) showed the worst fatigue performance. Analysis of total strain amplitude in the notch root with the aid of an elastoplastic finite-element (FE) model showed that the work hardening related to the subsurface deformation caused by the different broaching can account for the difference in fatigue lives. Differences in initiation and growth behavior were seen for the two broached finishes as well as for broached and subsequently polished samples. These differences are discussed in terms of a change in crack growth initiation and growth mechanisms due to the presence of the work-hardened layer.