Corrosion behaviour of copper-reinforced carbon electrodes in dilute hydrochloric acid solutions

The corrosion behaviour of experimentally prepared copper-reinforced carbon electrodes in dilute hydrochloric acid is investigated. The electrodes are not only directly attacked by the acid, but they are also subjected to galvanic corrosion. The baking temperature and time are the most crucial processing variables. A minimum in the corrosion rate is always achieved when the electrodes are baked at 400 °C for 1.5 h, the level depending on the copper content. The corrosion resistance increases progressively with the baking temperature as long as the baking time is less than 1.5 h. Baking for more than 1.5 h results in increasing corrosion rate. The presence of copper increases the corrosion resistance of the prepared electrodes.     

Monolithic integration of a 5.3 GHz regenerative frequency divider using a standard bipolar technology

A monolithic microwave frequency divider IC with an operating range of 1.4?5.3 GHz was developed and fabricated in a standard bipolar technology. The circuit operates on the principle of `regenerative frequency division?. Compared to the most popular divider concepts based on a master-slave D-flip-flop, an almost twice as high input frequency can be divided, provided that the same technology is used. A further advantage is the low power consumption.     

The influence of annealing on the conductivity of magnesium films

Polycrystalline magnesium films were deposited under ultrahigh vacuum by thermal evaporation onto a cooled silica substrate. During the growth process of a film a number of lattice defects are incorporated. It was found that the defect density decreases with increasing thickness. An annealing study of the electrical resistance and defect density in magnesium films was made. The results were interpreted on the basis of Vand's theory. The function F₀ expressing the law of distribution of the decay energies exhibited a maximum. For thick films there was no appreciable variation in the activation energy with thickness. In this case the evaluated activation energy E was found to be about 0.35 eV. For very thin films this energy decreases with increasing thickness.     

A 72-mW CMOS 802.11a direct conversion front-end with 3.5-dB NF and 200-kHz 1/f noise corner

A direct conversion 802.11a receiver front-end including a synthesizer with quadrature VCO has been integrated in a 0.13-/spl mu/m CMOS process. The chip has an active area of 1.8 mm/sup 2/ with the entire RF portion operated from 1.2 V and the low frequency portion operated from 2.5 V. Its key features are a current driven passive mixer with a low impedance load that achieves a low 1/f noise corner and an high I-Q accuracy quadrature VCO. Measured noise figure is 3.5 dB with an 1/f noise corner of 200 kHz, and an IIP3 of -2 dBm. The synthesizer DSB phase noise integrated over a 10 MHz band is less than -36 dBc while its I-Q phase unbalance is below 1 degree.     

Conduction band states of transition metal (TM) high-k gate dielectrics as determined from X-ray absorption spectra

This paper uses X-ray absorption spectroscopy to study the electronic structure of the high-k gate dielectrics including TM and RE oxides. The results are applicable to TM and rare earth (RE) silicate and aluminate alloys, as well as complex oxides comprised of mixed TM/TM and TM/RE oxides. These studies identify the nature of the lowest conduction band d^* states, which define the optical band gap, E_g, and the conduction band offset energy with respect to crystalline Si, E_B. E_g and E_B scale with the atomic properties of the TM and RE atoms providing important insights for identification high-k dielectrics that meet performance targets for advanced CMOS devices.     

The specification and use of geotextile fin drains

This paper describes the composition, construction and uses of the rather special range of geotextile composites which have generally become known as ‘fin drains’. It tries to provide a generic definition of the term ‘fin drain’ which encompasses all current commercial products, and foreseeable types. In particular, it excludes composites which are intended for, or which function as, either pressure-driven water transporters, or capillary driven systems. Pressure-driven drains include, in particular, those drains commonly known as ‘wicks’ which are used for the relief of excess pore pressure in soft ground construction work. Similarly, a number of geotextiles have the facility of passing water within their plane by virtue of internal capillary attraction generated at the interfaces of the composite fine fibres. Such products transmit only small volumes of water, and their intended functions and design principles are entirely different from those of ground fin drains in the sense included in this paper.     

Replication and bonding techniques for integrated microfluidic systems

From the technical and economic points of view, systems integration, and packaging represent a crucial step in the production of microsystems. Compared to purely silicon- or glass-based systems, the variety of materials and geometries available for purely polymer microfluidic systems is much larger, due to the outstanding material properties. Moreover, polymers may be shaped and joined by comparably simple methods. Examples are polymer microreplication as well as various bonding methods. With them, complete polymer microsystems can be integrated. In addition, a number of established, compatible processes are available for the integration of functional elements that may also be made of other materials.