(BaTiO3)1-x + (Co0.5Ni0.5Nb0.06Fe1.94O4)x nanocomposites: Structure,morphology, magnetic and dielectric properties

Two phase-based nanocomposites consisting of dielectric barium titanate (BaTiO₃ or BTO) and magnetic spinel ferrite Co_0.5Ni_0.5Nb_0.06Fe_1.94O₄ (CNNFO) have been synthesized through solid state route. Series of (BaTiO₃)_1-x + (Co_0.5Ni_0.5Nb_0.06Fe_1.94O₄)_x nanocomposites with x content of 0.00, 0.25, 0.50, 0.75, and 1.00 were considered. The structure has been examined via X-rays diffraction (XRD) and indicated the occurrence of both perovskite BTO and spinel CNNFO phases in various nanocomposites. A phase transition from tetragonal BTO structure to cubic structure occurs with inclusion of CNNFO phase. The average crystallites size of BTO phase decreases, whereas that for the CNNFO phase increases with increasing x in various nanocomposites. The morphological observations revealed that the porosity is highly reduced, and the connectivity between grains is enhanced with increasing x content. The optical properties have been investigated by UV−vis diffuse reflectance spectroscopy. The deduced band gap energy (E_g) value is found to reduce with increasing the content of spinel ferrite phase. The magnetic as well as the dielectric properties were also investigated. The analysis showed that CNNFO ferrite phase greatly affects the magnetic properties and dielectric response of BTO material. The obtained findings can be useful to enhance the performances of magneto-dielectric composite-based systems.     

Graphene oxide-containing isocyanate-based polyimide foams: Enhanced thermal stability and flame retardancy

Isocyanate-based graphene oxide-containing polyimide foams were synthesized by a semi-prepolymer method. In this method, while the first solution containing pre-polymer was derived from pyromellitic dianhydride and excess polymethylene polyphenylene isocyanate (PM200), the second solution contains dianhydride derivatives, water, catalysts, surfactants, and graphene oxide. PIFs were prepared with 0%, 0.25%, 0.50%, 0.75%, and 1% graphene oxide by weight, respectively. PIFs exhibited a minimum side reaction and urea generation was not seen for all PIFs instead of imide bonding. The addition of graphene oxide (GO) leads to a more close-packed structure. Therefore, crosslinking density and thermal stability of graphene oxide-containing polyimide foams increased. Upon the addition of 1% GO, almost seven times higher compression strength was obtained compared to neat PIFs. Also, LOI values supported the theory that thermally stable and flame retardant PIFs can be synthesized via the isocyanate-based process with GO.     

Graphite intercalated polymer coatings on stainless steel

The use of graphite modified polymer films has been investigated, on stainless steel. Polythiophene and polypyrrole films have been synthesized electrochemically on stainless steel, and then very thin graphite layers were realized on polymer films. Since the graphite layer is not applicable as a top coat, polymeric top films were also electrosynthesized on graphite layers. Following this procedure, polypyrrole-graphite-polypyrrole and polythiophene-graphite-polythiophene coatings have been obtained on stainless steel. The corrosion behaviours of coated samples have been investigated in 0.1 M H₂SO₄ solution, by means of electrochemical impedance spectroscopy (EIS) and anodic polarization curves. The intercalation of graphite layer altered the performance and properties of coatings significantly. Especially, polypyrrole coating system was found to exhibit almost an excellent coating behaviour that hindered the attack of corrosive environment within 96 h exposure time. The EIS results of polypyrrole coating system were indicating to almost a perfect capacitive behaviour that the response was reflecting capacitive behaviour in a wide frequency region. This property was also examined with successive cyclic voltammograms in a potential range between 0.10 and 0.40 V (vs. Ag/AgCl). The charge densities involved in oxidation and reduction regions were determined for successive cycles and it was shown that coated sample was able to exhibit charge-discharge (i.e. oxidation and reduction) behaviour successfully, without any degradation.     

Determination of the optimum conditions for ion nitriding of AISI 5140 steel

AISI 5140 low alloy steel was ion nitrided under different process parameters including time (1, 4, 8 and 12 h), temperature (400, 450, 500 and 550 °C) and gas mixture ratio (0.05, 0.33, 1 and 3 N₂/H₂). By determining the fatigue strength, surface hardness, compound layer thickness and case depth, the optimum working conditions were determined by using a Taguchi design of experiment. After ion nitriding process, it is aimed to maximize fatigue strength, surface hardness and case depth as well as to minimize compound layer thickness. While the optimum conditions were determined, due to the goals (above aims) more than one being, the trade-off among goals was considered. First of all, each goal was optimised, separately. Then, all the goals were optimised together, considering the priority of the goals, and the optimum results were obtained at 0.05 N₂/H₂ gas mixture ratio, at the temperature of 450 °C and for 12 h process time.     

High-capacity quantum key distribution using Chebyshev-map values corresponding to Lucas numbers coding

We propose an approach that achieves high-capacity quantum key distribution using Chebyshev-map values corresponding to Lucas numbers coding. In particular, we encode a key with the Chebyshev-map values corresponding to Lucas numbers and then use k-Chebyshev maps to achieve consecutive and flexible key expansion and apply the pre-shared classical information between Alice and Bob and fountain codes for privacy amplification to solve the security of the exchange of classical information via the classical channel. Consequently, our high-capacity protocol does not have the limitations imposed by orbital angular momentum and down-conversion bandwidths, and it meets the requirements for longer distances and lower error rates simultaneously.     

Batch sequencing and cooperation

Game theoretic analysis of sequencing situations has been restricted to manufacturing systems which consist of machines that can process only one job at a time. However, in many manufacturing systems, operations are carried out by batch machines which can simultaneously process multiple jobs. This paper aims to extend the game theoretical approach to the cost allocation problems arising from sequencing situations on systems that consist of batch machines. To analyze the allocation problem at hand, it focusses on the existence of core elements, convexity, and the Shapley value.     

To watch from distance: an interactive film model based on Brechtian film theory

With the emergence of new media, interactive film projects have mainly struggled to resolve the contradiction between dramatic structures and interaction. Dramatic film presents identification with the main character, where the viewer is constantly oppressed by the narrative, and therefore lost in illusion. In this context, when we bring on the scene interaction, the drama apparently starts to lose its power.

In this article, a new interactive film model based on Brechtian film theory is proposed. This model presents a new way of spatiotemporal construction where different audiovisual combinations can be viewed successively, and this way the viewer can actively construct his/her own story. Theoretical framework of the Brechtian interactive film model is supported by an interactive film application, named Academia. The main feature of the model is that, while interaction is very simple, the continuity of the narrative is preserved and the film requiring an intellectual level of interpretation.