Development of silicon wafer packaging technology for deep UV LED

This paper reports a deep‐ultraviolet LED (deep‐UV‐LED) package based on silicon MEMS process technology (Si‐PKG). The package consists of a cavity formed by silicon crystalline anisotropic etching, through‐silicon vias (TSVs) filled with electroplated Cu, bonding metals made of electroplated Ni/AuSn and a quartz lid for hermetic sealing. A deep‐UV LED die is directly mounted in the Si‐PKG by AuSn eutectic bonding without a submount. It has advantages in terms of size, heat dissipation, light utilization efficiency, productivity and cost over conventional AlN ceramic packages. We confirmed a light output of 30 mW and effective reflection on Si (111) cavity slopes in the Si‐PKG. Based on simulation, further improvement of the optical output is expected by optimizing DUV‐LED die mount condition.     

Application results of a prototype ultrasonic liquid film sensor to a 7 MPa steam–water two-phase flow experiment

A prototype ultrasonic liquid film sensor was applied to a high-temperature steam–water two-phase flow experiment. The liquid film sensor was vertically installed in a loop which was connected to HUSTLE, a multi-purpose steam source test facility. The hydraulic diameter of the measurement section was 9.4 mm. The output waveforms of the sensor were acquired with a digital oscilloscope. The fluid temperature and system pressure were kept at 288 °C and 7.2 MPa, respectively, during the experiment. The pulse-echo method was used to calculate the liquid film thickness. The cross-correlation calculation was utilized to determine the time difference between the pulse reflected at the sensor surface and the pulse reflected at the liquid film surface. The time-averaged liquid film thicknesses were less than 0.055 mm in the annular flow condition. The increase of the time-averaged thickness was small with the change of the gas momentum flux. The film thicknesses measured with the sensor were compared with the past experimental results; the former were smaller than one-fourth of the thickness estimated as the mean film thickness. The comparison results suggested that the continuous liquid sublayer thickness was measured with the liquid film sensor.     

How to construct small probabilistic roadmaps with a good coverage?

We investigate how we can construct small probabilistic roadmaps in a reasonable time while still keeping a good coverage and connectivity. We propose a new neighborhood-based method that can reduce the size of the roadmaps by filtering out unnecessary nodes. We then experimentally test it against a basic probabilistic roadmap planner and a visibility-based planner. We use both a uniform sampling and a bridge test sampling in our tests. The results show that the neighborhood-based method can reduce the number of nodes considerably. The neighborhood-based method is simple to implement, it works well with a uniform sampling, and it does not need any additional parameters when compared with the basic planner.     

Epitaxial p-type SiC as a self-driven photocathode for water splitting

Solar-to-hydrogen conversion efficiencies of water-splitting photochathodes using epitaxially grown p-type 4H-, 6H- and 3C-SiC were estimated in a two-electrode system without applying any external bias. By using electrode materials with small oxygen overpotentials as counter electrodes, the photocurrent became comparable to that observed in a three-electrode system with a suitable bias. Estimated efficiencies seem to depend on the bandgap of the SiC polytypes. For the 3C-SiC, the obtained efficiency was 0.38%, which is so far the highest value reported for SiC. We confirmed that the hydrogen volumes estimated from the photocurrent were almost the same as actual volumes observed by gas chromatography.     

Impact of Dynamic Interlayer Interactions on Thermal Conductivity of Ca3Co4O9

The phonon thermal conductivity of misfit-layered Ca₃Co₄O₉ has been calculated by perturbed molecular dynamics using a classical force field. Detailed numerical analyses reveal that, in spite of its smaller cross-sectional area, the CoO₂ layer transports more heat than the thicker rock salt (RS) layer, although its local thermal conduction is more suppressed than in another layered cobaltite, Na _x CoO₂. The origins of these differences have been elucidated through careful examination of the atomic arrangements in each layer. Since thermal conduction in the RS layer can be reduced without deteriorating electronic properties for which the CoO₂ layer is responsible, it is suggested that the RS layer should be modified to further suppress the overall in-plane thermal conductivity. Computational experiments with increasing number of Ca–O planes in the RS layer showed the opposite trend to what can be predicted based on the misfit between two dissimilar layers. Further analyses to reveal the origin of these unexpected results provide yet another strategy to further decrease the thermal conductivity, namely to control the dynamic interference between atoms across the interface between two layers.     

Designing block copolymer architectures for targeted membrane performance

Using a combination of block copolymer self-assembly and non-solvent induced phase separation, isoporous ultrafiltration membranes were fabricated from four poly(isoprene-b-styrene-b-4-vinylpyridine) triblock terpolymers with similar block volume fractions but varying in total molar mass from 43 kg/mol to 115 kg/mol to systematically study the effect of polymer size on membrane structure. Small-angle X-ray scattering was used to probe terpolymer solution structure in the dope. All four triblocks displayed solution scattering patterns consistent with a body-centered cubic morphology. After membrane formation, structures were characterized using a combination of scanning electron microscopy and filtration performance tests. Membrane pore densities that ranged from 4.53 × 10¹⁴ to 1.48 × 10¹⁵ pores/m² were observed, which are the highest pore densities yet reported for membranes using self-assembly and non-solvent induced phase separation. Hydraulic permeabilities ranging from 24 to 850 L m⁻² h⁻¹ bar⁻¹ and pore diameters ranging from 7 to 36 nm were determined from permeation and rejection experiments. Both the hydraulic permeability and pore size increased with increasing molar mass of the parent terpolymer. The combination of polymer characterization and membrane transport tests described here demonstrates the ability to rationally design macromolecular structures to target specific performance characteristics in block copolymer derived ultrafiltration membranes.     

The association of distress and sleeping problems with physicians’ intentions to change profession: The moderating effect of job control.

The present study examined whether job control moderated the association between stress indicators (distress and sleeping problems) and intentions to change profession among 2,650 Finnish physicians. Ordinal logistic regression analysis was applied. The authors found that high levels of distress and sleeping problems were associated with higher levels of intentions to change profession, whereas high job control was associated with lower levels of intentions to change profession even after adjusting for the effects of gender, age, and employment sector. In addition, high job control was able to mitigate the positive association that distress and sleeping problems had with intentions to change profession. Our findings highlight the importance of offering more job control to physicians to prevent unnecessary physician turnover. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Performance tuning and sparse traversal technique for a cell‐based fetch length algorithm on a GPU

For determining distances (fetch lengths) from points to polygons in a two‐dimensional Euclidean plane, cell‐based algorithms provide a simple and effective solution. They divide the input area into a grid of cells that cover the area. The objects are stored into the appropriate cells, and the resulting structure is used for solving the problem. When the input objects are distributed unevenly or the cell size is small, most of the cells may be empty. The representation is then called sparse. In the method proposed in this work, each cell contains information about its distance to the nonempty cells. It is then possible to skip over several empty cells at a time without memory accesses. A cell‐based fetch length algorithm is implemented on a graphics processing unit (GPU). Because control flow divergence reduces its performance, several methods to reduce the divergence are studied. While many of the explicit attempts turn out to be unsuccessful, sorting of the input data and sparse traversal are observed to greatly improve performance: compared with the initial GPU implementation, up to 45‐fold speedup is reached. The speed improvement is greatest when the map is very sparse and the points are given in a random order. Copyright © 2015 John Wiley & Sons, Ltd.