A Low Complexity Suboptimal Energy-Based Detection Method for SISO/MIMO Channels

In this paper, we propose an actually novel and simple method for detection of transmitted symbols in MIMO channels. This method is based on the energy level of the received signals. At the receiver, we assume the knowledge of channel state information which can be estimated by different methods, e.g. by sending pilots. So, we can determine all possible levels of energy. This computation of energy levels is done only once for the quasi-static channels. Energy of the received signals is a criterion by which we can estimate the transmitted symbols. Detection of transmitted signal is made based on the nearest energy level and the points which lie on it. In other words, we have restricted our search space to a new smaller space with different levels of energy. Simulation results confirm approximately the same performance between the maximum-likelihood detector and the proposed approach especially in high signal-to-noise ratios with a remarkable reduction in the computational complexity.     

Antimicrobial Property,Antioxidant Capacity,and Cytotoxicity of Essential Oil from Cumin Produced in Iran

ABSTRACT: Cumin (Cuminum cyminum) is one of the commonly used spices in food preparations. It is also used in traditional medicine as a stimulant, a carminative, and an astringent. In this study, we characterized the antimicrobial, antioxidant, and cytotoxic activities of cumin. E. coli, S. aureus, and S. faecalis were sensitive to various oil dilutions. The total phenol content of the essential oil was estimated to be 33.43 μg GAE/mg of the oil. The oil showed higher antioxidant activity compared with that of BHT and BHA. The cumin essential oil exhibited a dose-dependent scavenging of DPPH radicals and 5.4 μg of the oil was sufficient to scavenge 50% of DPPH radicals/mL. At a concentration of 0.1 μL/mL, oil destructed Hela cells by 79%. The antioxidant activity of cumin essential oil might contribute to its cytotoxic activity. Acute and subchronic toxicity was studied in a 30-d oral toxicity study by administration to Wistar rats of the essential oil. A 17.38% decrease in WBCs count, and 25.77%, 14.24%, and 108.81% increase in hemoglobin concentration, hematocrit, and platelet count, respectively, were noted. LDL/HDL ratio was reduced to half, which adds to the nutritional effects of cumin. Thus, cumin with a high phenolic content and good antioxidant activity can be supplemented for both nutritional purposes and preservation of foods.     

Grading of gliomas using transfer learning on MRI images

Magnetic Resonance Materials in Physics, Biology and Medicine - Despite the critical role of Magnetic Resonance Imaging (MRI) in the diagnosis of brain tumours, there are still many pitfalls in the...     

An analytical investigation of near-field plates

This paper describes an analytical approach to modeling near-field plates, which are non-periodic grating-like structures that can focus electromagnetic waves to subwavelength dimensions. The analysis provides additional insight into the operation and design of such plates that focus cylindrical waves to subwavelength resolutions. Explicit expressions for the current density induced on the plate and its impedance profile are derived. The analytical expressions are validated numerically.     

Morphology enhancement of TiO2/PVP composite nanofibers based on solution viscosity and processing parameters of electrospinning method

In this work, different sol solutions with various titanium tetraisopropoxide (TIP)/glacial acetic acid ratios in 2‐propanol with 5 wt % poly(vinyl pyrrolidone) (PVP) (M_w = 360,000 g/mol) were prepared and electrospun. Composition of the prepared sols and as‐spun TiO₂/PVP nanofibers were determined by Fourier transform infrared and Raman spectroscopy methods. Morphology of the electrospun TiO₂/PVP nanofibers was studied by scanning electron microscopy and transmission electron microscopy (TEM) techniques. Rheometry measurements of the sol solutions showed decrease of viscosity upon the addition of TIP to the polymer solutions with constant polymer and acid concentrations. The sol solution having the lowest viscosity (at shear rate 10 s^?1) but the highest TIP/glacial acetic acid ratio showed beaded nanofibers morphology when electrospun under 10 and 12 kV applied voltage while injection rate, needle tip to collector distance, and needle gauge were kept constant. However, smooth electrospun TiO₂/PVP composite nanofibers with the average nanofibers diameters (148 ± 79 nm) were achieved under the same condition when applied voltage increased to 15 kV. TEM micrographs of the electrospun TiO₂/PVP nanofiber showed that the TiO₂ particles with continuous structure are formed at the middle of the nanofiber and distributed along its axis. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46337.     

Influence of Ni/Co binders and Mo2C on the microstructure evolution and mechanical properties of (Ti0.93W0.07)C–based cermets

In this research, solid–solution powder of (Ti_0.93W_0.07)C was synthesized by high–energy ball mill method followed by carbothermal reduction process. Subsequently, the acquired powder was blended with Ni/Co and Mo₂C secondary carbide, and sintered under the optimized temperature (1510?°C) for 1?h to produce the modulated cermets. A typical core–rim structure formation with solid–solution phases was confirmed by backscattered electrons studies using a Field Emission electron scanning microscope. The hardness of the synthesized cermets was enhanced by increasing the specific amount of Mo₂C. The acquired results demonstrate that the binder type has a prominent influence on the microstructure and hardness of the prepared cermets. The hardness of (Ti_0.93W_0.07)C–xMo₂C–Ni cermet increased ~ 9%, when nickel was partially substituted by cobalt.     

Microfluidic behavior in melt-spun hollow and liquid core fibers

The development of thermoplastic fibers containing a liquid core is described. Internal morphology analysis confirms that the liquid-containing core is composed of a continuous cylindrical microchannel of constant diameter. Microfluidic experiments on both liquid core and reference hollow fibers were conducted by pumping distilled water through several filaments simultaneously. The observed fluid motions are satisfactorily described by the Hagen-Poiseuille law, indicating that the hollow and liquid core fibers have internal diameters of 31.6 and 14.8 µm, respectively. Flushing the liquid core fibers with a surfactant solution efficiently removes the saturated ester initially used during the melt spinning of the fiber.     

Reverse iodine transfer polymerization of vinyl acetate and vinyl benzoate: synthesis and characterization of homo‐ and copolymers

Homo‐ and copolymers of vinyl esters including vinyl acetate (VAc) and vinyl benzoate (VBz) were synthesized via the reverse iodine transfer radical polymerization technique. Polymerization was carried out in the presence of iodine as the in situ generator of the transfer agent and 2,2′‐azobis(isobutyronitrile) as the initiator at 70 °C. Reverse iodine transfer radical homopolymerization of VAc and VBz led to conversions of 76 and 57%, number‐average molecular weights of 8266 and 9814 g mol^?1 and molecular weight distributions of 1.58 and 1.49, respectively. The microstructure of the synthesized polymers was investigated in detail using gel permeation chromatography, ¹H NMR, ¹³C NMR and distortionless enhancement of polarization transfer (135° decoupler pulse) techniques. Relatively narrow molecular weight distribution and controlled and predictable trend of molecular weight versus conversion were observed for the synthesized polymers, showing that reverse iodine transfer radical homo‐ and copolymerization of VAc and VBz proceeded with controlled characteristics. Results of molecular weight and its distribution along with the ¹H NMR spectra recorded for homo‐ and copolymers indicated that side reactions can occur during the course of polymerization with a significant contribution when VAc, even in a small amount, was present in the reaction mixture. This can result in polymer chains with aldehyde dead end and broadening of the molecular weight distribution. © 2015 Society of Chemical Industry     

Spark plasma sintering of Al-doped ZrB2–SiC composite

This research presents the influence of Al addition on microstructure and mechanical behavior of ZrB₂–SiC ultra-high temperature ceramic matrix composite (UHTCMC) fabricated by spark plasma sintering (SPS). A 2.5?wt% Al-doped ZrB₂–20?vol% SiC UHTCMC was produced by SPS method at 1900?°C under a pressure of 40?MPa for 7?min. The microstructural and phase analysis of the composite showed that aluminum-containing compounds were formed in-situ during the SPS as a result of chemical reactions between Al and surface oxide films of the raw materials (i.e. ZrO₂ and SiO₂ on the surfaces of ZrB₂ and SiC particles, respectively). The Al dopant was completely consumed and converted to the intermetallic Al₃Zr and Al₄Si compounds as well as Al₂O₃ and Al₂SiO₅. A relative density of 99.8%, a hardness (HV5) of 21.5?GPa and a fracture toughness (indentation method) of 6.3?MPa?m^1/2 were estimated for the Al-doped ZrB₂–SiC composite. Crack bridging, branching, and deflection were identified as the main toughening mechanisms.