An Analog Front‐End Circuit for ISO/IEC 14443‐Compatible RFID Interrogators

An analog front‐end circuit for ISO/IEC 14443‐compatible radio frequency identification (RFID) interrogators was designed and fabricated by using a 0.25 µm double‐poly CMOS process. The fabricated chip was operated using a 3.3 Volt single‐voltage supply. The results of this work could be provided as reusable IPs in the form of hard or firm IPs for designing single‐chip ISO/IEC 14443‐compatible RFID interrogators.     

Effect of Annealing on the Surface Microstructure of Y-Ba-Cu-O Superconducting Ceramics

Precusors to the YBa₂Cu₃O_7-δ material were prepared by both the oxalate precipitation method and conventional ceramic processing. Second-phase grains were observed to develop on the exposed fracture surface during annealing at 500° to 600°C in an ambient atmosphere. The second-phase grains were identified to be BaCO₃ using EDX and XRD. The liquid phase, which was formed because of local chemical inhomogeneity in the Y-Ba-Cu-O system, contributed to the formation of second-phase grains as a source of Ba.     

汉城旅游商务区的空间特征:以梨泰院专项旅游区为例

韩国许多城市指定了专项旅游区,通过提供若干激励政策来促进城市旅游.汉城的梨泰院1997年被指定为专项旅游区并成为CBD的一部分.本研究追溯了它作为旅游购物区的变化过程,并通过调查其土地使用找出城市空间结构的变化特征.最后,作者提出了对发展城市旅游的政策性建议,包括减少指定性区域和特殊政策.     

Microstructural investigation of long-term degradation mechanisms in GFRP dowel bars for jointed concrete pavement

Steel dowel bar is used to transfer loads in concrete pavement slab. However, once the steel dowel bar corrodes, it may cause faults, such as joint freezing in concrete pavement, level differences resulting from spalling or decreased efficiency of load transfer, etc., which are the same problems experienced by typical reinforcing steel. This study evaluated the applicability of glass fiber-reinforced polymer (GFRP) dowel bar as a substitute for steel dowel bar. A microstructural analysis was conducted to examine the decrease in durability of GFRP dowel bar exposed to deterioration environments. To analyze the deterioration mechanism of GFRP dowel bar, scanning electron microscopy was employed and the porosity was measured by the gas absorption method. It was concluded that the longer the GFRP dowel bar was exposed to deterioration environments, the more the interlaminar shear stress decreased. This result was validated by the microstructural analysis. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation of monodisperse poly(vinyl alcohol) microspheres by heterogeneous surface saponification and iodine complex formation

Monodisperse poly(vinyl acetate) (PVAc) microspheres with high molecular weight obtained by suspension polymerization of vinyl acetate were saponified in alkaline aqueous solution to keep their spherical structure. The saponification was restricted on the surface of the PVAc microspheres and obtained particles had skin/core structure. Various poly(vinyl alcohol) (PVA) microspheres with different diameters and degrees of saponification (DSs) were obtained. The conversion of PVAc to PVA during the heterogeneous surface saponification time were examined by nuclear magnetic resonance spectroscopy and after 72 h hydrogel type PVA microspheres completely saponified were obtained. The crystal melting temperatures of the microspheres obtained by the saponification were measured a constant value of 238°C irrespective of varying DS, and the peaks became enlarged as reaction time. Iodine complexes were formed in saponified microspheres with DS of 41% and 99% by immersing them in I₂/KI aqueous solution and decomposed by the reduction of I₂ in the complexes to 2I^? using sodium sulfite to confirm whether the skin formed through the saponification was composed of PVA with high VA content. Obviously, characteristic blue color developments owing to I₅^?‐PVA complexes were observed in both saponified regions and a red in the PVAc core. Consequently, it was concluded that the PVA skins formed by heterogeneous surface saponification had high DSs. Such complexes endowed polymeric microspheres a good radiopacity which would be useful in clinical treatment of vascular diseases and were examined by X‐ray irradiation image. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation of aligned polyetherimide fiber by electrospinning

Fifteen to 20 wt % polyetherimide (PEI) solutions with 1-methyl-2-pyrrolidinone (NMP) were prepared. The electrical conductivity and surface tension of the solutions were determined. The fiber spinning technique of electrospinning was optimized in order to prepare unidirectionally aligned, structurally oriented nanofiber tows. The morphology of the PEI fibers was investigated using field emission scanning electron microscopy (FESEM). The well-aligned fibers with diameters between 0.58 and 0.90 μm (FESEM) were collected by electrospinning 20 wt % PEI solutions with NMP in the range of 8–10 kV onto a target rotating with a surface velocity 9.8 m/s. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Differentially coherent code acquisition in the MIMO-aided multi-carrier DS-CDMA downlink

Both differentially coherent and non-coherent code acquisition schemes designed for the multiple-input multiple-output (MIMO)-aided multi-carrier (MC)-DS-CDMA downlink are analysed, when communicating over uncorrelated Rayleigh channels. The attainable mean acquisition time (MAT) performance is studied as a function of both the number of multiple transmit/multiple receive antennas and that of the number of subcarriers. It is demonstrated that in contrast to the expectations, when the number of multiple transmit antennas and/or that of the subcarriers is increased in both the differentially coherent and the non-coherent code acquisition scenarios, the achievable MAT deteriorates over the entire signal-to-interference plus noise ratio (SINR) per chip (E_c/I_o) range considered, except for the scenario of single-carrier (SC)-DS-CDMA using P = 2 transmit antennas and R = 1 receive antenna. As expected, the degree of performance degradation depends upon the specific scheme and the E_c/I_o ratio considered, although paradoxically, the correctly synchronised MIMO-aided system is capable of attaining its target bit error ratio performance at reduced SINR values.     

Motion based object tracking with mobile camera

An efficient algorithm which detects and tracks a moving object is proposed. The global motion energy caused by camera movement is eliminated by finding the maximal matching position with the cross-correlation value between two consecutive frames using the spiral scanning technique. The region of a moving object is segmented exactly by combining the results of the temporal derivatives and edge map from one image, and the actual centroid of the moving object is determined as the mid-point of the cumulative distribution of the projection profile of the region