Effect of anisotropy of tin on thermomechanical behavior of solder joints

Properties of body centered tetragonal tin are highly anisotropic. As a consequence large stresses can develop at the tin grain boundaries due to coefficient of thermal expansion mismatch during temperature excursions. A modeling approach to evaluate the 3D stress states that develop at grain boundaries during thermomechanical fatigue in tin-based solder is presented. Development of significant amounts of stresses in the plane of the grain boundary can cause grain-boundary sliding and surface-relief effects, while those normal to the grain boundary can cause grain-boundary decohesion and cracking.     

Start-up and steady-state results of a full-scale UASB reactor treating malting wastewater.

An Imhoff tank was reconstructed into a 250 m3 UASB reactor in order to treat a malting plant wastewater. The UASB was inoculated with sludge from an anaerobic lagoon used for slaughterhouse wastewater treatment. After two months of operation the reactor achieved full load with an HRT of 17 h, a COD removal higher than 80% and a biogas production of 300 m3/day (77% average methane content), with an organic loading rate of 3.6 kgCOD/m3.d (0.24 kgCOD/kgVSS.d). A yield coefficient of 0.09 gVSS/gCODrem was found from a mass balance. The fat present in the inoculated sludge (48 mg/gSSV) did not affect the start up performance. Sludge from the inoculum with high content of fat (270 mg/gSSV), was separated by flotation in the first week of operation. The COD removal efficiency was scarcely influenced by the reactor operation temperature (17-25 degrees C).     

Mechanism of the inhibiting effect of diphenylamine in the oxidation of hydraulic oils

The mechanism of the inhibiting effect of diphenylamine during the oxidation of two base stocks of hydraulic oils were studied at 120, 130, and 140°C. The key reactions in the mechanism of the action of the inhibitor were identified, and the values of the kinetic parameters and their activation energies were determined. The kinetic parameters were calculated, and the salient kinetic features of the inhibited oxidation of the two specimens were compared at 70°C, the temperature of accelerated testing of hydraulic oils. The results of this prediction were analyzed, and the reasons for differences in the oxidation stability of the samples examined were established.     

An application of chemometric techniques to analyze the effects of the wave function modifications on the intermolecular stretching frequencies of the hydrogen-bonded complexes

Factorial design and principal component models are used to determine how ab initio H-bond stretching frequencies depend on characteristics of the molecular orbital wave functions of acetylene–HX, ethylene–HX and cyclopropane–HX π-type hydrogen complexes with X=F, Cl, CN, NC and CCH. The results obtained for the three sets of complexes show that factorial design and principal component analyses complement each other. Factorial design calculations clearly show that these frequencies are affected mostly by inclusion of electron correlation on the calculation level. On average, their values are increased by about 25 cm⁻¹ due to a change from the Hartree–Fock (HF) to Möller–Plesset 2 (MP2) level. Valence, diffuse and polarization main effects as well as valence–diffuse, diffuse–correlation and polarization–correlation interaction effects are also important to better describe a factorial model to the H-bond stretching frequencies of these hydrogen complexes. This simplified model has been successful in reproducing the complete ab initio results, which correspond to two hundred and forty calculations. Principal component analyses applied only to hydrogen-bonded complexes whose experimental frequencies are known, has revealed that the six-dimensional original space can be accurately represented by a bidimensional space defined by two principal components. Its graphical representation reveals that the experimental intermolecular stretching frequencies are in closest agreement with the MP2/6–31+G and MP2/6–311+G ab initio results.     

Motive Force in a Complex Model of Mass Transfer

Relations for determining a motive force in a complex model of mass transfer as applied to concurrent, countercurrent, and cross motion of the vapor and liquid phases have been introduced. These forces have been compared for different forms of organization of the flow, and their comparison with similar quantities from the known Murphree and Hausen models is presented.     

Construction and qualification of the pre-series MQM superconducting quadrupoles for the LHC insertions

The LHC insertions will be equipped with individually powered MQM superconducting quadrupoles, produced in three versions with magnetic lengths of 2.4 m, 3.4 m, and 4.8 m. The quadrupoles feature a 56 mm aperture coil, designed on the basis of an 8.8 mm wide Rutherford-type NbTi cable for a nominal gradient of 200 T/m at 1.9 K and 5390 A. A total of 96 quadrupoles are in production in Tesla Engineering, UK. In this report we describe the construction of the pre-series MQM quadrupoles and present the results of the qualification tests.     

Review Processing, properties and applications of reactive silica from rice husk—an overview

Rice husk is an abundantly available waste material in all rice producing countries. In certain regions, it is sometimes used as a fuel for parboiling paddy in the rice mills. The partially burnt rice husk in turn contributes to more environmental pollution. There have been efforts not only to overcome this but also to find value addition to these wastes using them as secondary source of materials. Rice husk contains nearly 20% silica, which is present in hydrated amorphous form. On thermal treatment, the silica converts to crystobalite, which is a crystalline form of silica. However, under controlled burning conditions, amorphous silica with high reactivity, ultra fine size and large surface area is produced. This micro silica can be a source for preparing advanced materials like SiC, Si₃N₄, elemental Si and Mg₂Si. Due to the high pozzolanic activity, this rice husk silica also finds application in high strength concrete as a substitute for silica fume. Possibility of using this silica as filler in polymers is also studied. The present paper is an attempt to consolidate and critically analyse the research work carried out so far on the processing, properties and application of rice husk silica in various laboratories and also highlighting some results on the processing and characterization of RHA and reactive silica obtained from it in the authors' laboratory.     

Experimental characterisation of the drying effect on uniaxial mechanical behaviour of mortar

The main objective of this present study was to evaluate, for a standard mortar, the drying effect on its mechanical behaviour. Numerous uniaxial compression tests were thus performed with loading-unloading cycles. They were carried out on different samples previously preserved under various conditions of conservation: preserved from desiccation, air drying and rapid drying at 60°C. The obtained results showed significant influences of these conditions on the material behaviour (increase in strength, decrease in Young's modulus and Poisson's ratio) and the necessity of taking into account the coupling effects between mechanical—poromechanical behaviours and drying.     

Trajectory control of incompletely restrained parallel-wire-suspended mechanism based on inverse dynamics

This paper discusses parallel wire mechanisms where an end-effector of the mechanism is suspended by multiple wires. The mechanisms enable not only three-dimensional (3-D) positioning but also 3-D orienting of the end-effector, unlike typical wire suspension-type mechanisms such as overhead crane. To discuss the parallel-wire-suspended mechanisms generally, two forms of basic dynamic equations are presented. Then the parallel wire mechanisms are classified into two types based on the basic equations. Dynamical properties of the two types of wire-suspended positioning mechanism are discussed. In this paper, one of the wire-suspended mechanism, incompletely restrained-type parallel wire mechanism, is mainly discussed on its inverse dynamics problem and its trajectory control problem. The inverse dynamics problem for the incompletely restrained-type mechanism plays an important role on its control problem, because the mechanism has low stiffness based on incomplete constraints on the suspended object which is governed by its dynamics. The paper proposes an antisway control method for the suspended object. In the method, the inverse dynamics calculation is used for nonlinear dynamics compensation to control the suspended object of the incompletely restrained parallel wire mechanism.     

Thermal cracking of acid tars to asphalts as a process for utilization of refinery wastes

The feasibility of manufacture of asphaltic materials by means of the thermal cracking of acid tars was shown and a corresponding bench-scale unit was designed. The dependence of the viscosity characteristics of the obtained compositions on the temperature and time of the process was examined using the penetration technique.