The bonding effect of adhesive systems and bulk-fill composites to sound and caries-affected dentine

Purpose: To investigate the influence of adhesive type and increment thickness on shear bond strength of flowable bulk-fill resin composites compared with a flowable conventional resin composite, in both sound and caries-affected dentine.

Methods: Shear bond strength was tested in 100 extracted human molars with coronal dentine caries. Half of the teeth were restored with Adper? Easy Bond and the other half with Adper? Single Bond Plus. Bonded surfaces were restored with Filtek? Ultimate Flow and two bulk-fill composites (SDR and X-tra base) (n = 10 teeth for each subgroup). Restorations of 4 mm were performed with incremental or bulk-fill technique. The shear bond was determined and statistically analysed using three-way ANOVA and Bonferroni multiple comparison post hoc tests (p ≤ 0.05). Dentine–resin interfaces were evaluated by scanning electron microscopy.

Results: For both adhesives, the highest shear bond strength values were obtained for sound dentine. In sound dentine, the highest bond strength observed with Easy Bond when used in 2-mm increments of SDR. In caries-affected dentine, Single Bond in combination with SDR displayed significantly lower bond strength.

Conclusion: There was no significant difference in shear bond strength between the incremental and bulk-fill groups for molars with sound dentine when the etch-and-rinse adhesive system was used; however, for the self-etch adhesive system, incremental application caused higher bond strength than bulk application.     

A Comparative Study on Exergetic Performance Assessment for Drying of Broccoli Florets in Three Different Drying Systems

This article deals with the exergy analysis and evaluation of broccoli in three different drying systems. The effects of drying air temperature on the exergy destruction, exergy efficiency, and exergetic improvement potential of the drying process were investigated. The exergy destruction rate for the drying chamber increased with the rise in the drying air temperature at 1.5 m/s, both in the tray and the heat pump dryer. The highest exergy efficiency value was obtained as 90.86% in the fluid bed dryer in comparison to the other two drying systems and the improvement potential rate was the highest in the heat pump dryer during drying of broccoli at the drying air temperature of 45°C and the drying air velocity of 1.0 m/s.     

Investigation of luminescence centers inside InGaN/GaN multiple quantum well over a wide range of temperature and injection currents

Journal of Materials Science: Materials in Electronics - InGaN/GaN multiple quantum well-based light-emitting diode LEDs were investigated over a wide range of injection currents (0.04 mA–0.1...     

A comparative analysis of classification algorithms in data mining for accuracy, speed and robustness

Classification algorithms are the most commonly used data mining models that are widely used to extract valuable knowledge from huge amounts of data. The criteria used to evaluate the classifiers are mostly accuracy, computational complexity, robustness, scalability, integration, comprehensibility, stability, and interestingness. This study compares the classification of algorithm accuracies, speed (CPU time consumed) and robustness for various datasets and their implementation techniques. The data miner selects the model mainly with respect to classification accuracy; therefore, the performance of each classifier plays a crucial role for selection. Complexity is mostly dominated by the time required for classification. In terms of complexity, the CPU time consumed by each classifier is implied here. The study first discusses the application of certain classification models on multiple datasets in three stages: first, implementing the algorithms on original datasets; second, implementing the algorithms on the same datasets where continuous variables are discretised; and third, implementing the algorithms on the same datasets where principal component analysis is applied. The accuracies and the speed of the results are then compared. The relationship of dataset characteristics and implementation attributes between accuracy and CPU time is also examined and debated. Moreover, a regression model is introduced to show the correlating effect of dataset and implementation conditions on the classifier accuracy and CPU time. Finally, the study addresses the robustness of the classifiers, measured by repetitive experiments on both noisy and cleaned datasets.     

Interfacial Tension in the CaO-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-SiO<Subscript>2</Subscript>-(MgO) Liquid Slag–Solid Oxide Systems

Interfacial phenomenon is critical in metal processing and refining. While it is known to be important, there are little data available for key oxide systems in the literature. In this study, the interfacial tension (σ _LS) of liquid slag on solid oxides (alumina, spinel, and calcium aluminate), for a range of slags in the CaO-Al₂O₃-SiO₂-(MgO) system at 1773 K (1500 °C), has been evaluated. The results show that basic ladle-type slags exhibit lower σ _LS with oxide phases examined compared to that of acid tundish-type slags. Also, within the slag types (acid and base), σ _LS was observed to decrease with increasing slag basicity. A correlation between σ _LS and slag structure was observed, i.e., σ _LS was found to decrease linearly with increasing of slag optical basicity (Λ) and decrease logarithmically with decreasing of slag viscosity from acid to base slags. This indicated a higher σ _LS as the ions in the slag become larger and more complex. Through a work of adhesion (W) analysis, it was shown that basic ladle slags with lower σ _LS result in a greater W, i.e., form a stronger bond with the solid oxide phases examined. This indicates that all other factors being equal, the efficiency of inclusion removal from steel of inclusions of similar phase to these solid oxides would be greater.     

<Emphasis Type="Italic">In Situ</Emphasis> Observation of Calcium Aluminate Inclusions Dissolution into Steelmaking Slag

The dissolution rate of calcium aluminate inclusions in CaO-SiO₂-Al₂O₃ slags has been studied using confocal scanning laser microscopy (CSLM) at elevated temperatures: 1773 K, 1823 K, and 1873 K (1500 °C, 1550 °C, and 1600 °C). The inclusion particles used in this experimental work were produced in our laboratory and their production technique is explained in detail. Even though the particles had irregular shapes, there was no rotation observed. Further, the total dissolution time decreased with increasing temperature and decreasing SiO₂ content in the slag. The rate limiting steps are discussed in terms of shrinking core models and diffusion into a stagnant fluid model. It is shown that the rate limiting step for dissolution is mass transfer in the slag at 1823 K and 1873 K (1550 °C and 1600 °C). Further investigations are required to determine the dissolution mechanism at 1773 K (1500 °C). The calculated diffusion coefficients were inversely proportional to the slag viscosity and the obtained values for the systems studied ranged between 5.64 × 10^?12 and 5.8 × 10^?10 m²/s.     

Cyclic fatigue resistance of rotary NiTi instruments produced with four different manufacturing methods

The aim of this study was to compare the cyclic fatigue resistance of rotary NiTi files, produced with four different manufacturing methods on specially designed dynamic models that simulated clinical conditions. In this study, 120 files, consisting of 30 files for Typhoon, ProTaper Next, RaCe, and Twisted Files nickel titanium rotary systems were used. The 30 files of each group were divided into three subgroups to be used in artificial canals with a 60° angle of curvature and radii of curvature of 2, 5, and 8 mm (n = 10). All files were rotated in the artificial canals until fracture occurred and the number of cycles to fracture was calculated. The data were analyzed using one‐ and two‐way analyses of variance and Tamhane multiple comparison tests. In all three groups, Typhoon instruments had the highest number of cycles to failure than the RaCe, ProTaper Next, and Twisted Files instruments, and the difference statistically significant (p < .05). There were no significant differences between the RaCe, ProTaper Next, and Twisted Files groups (p > .05). The CM wire Typhoon system was significantly more resistant to cyclic fatigue compared to the other file systems in all three artificial canals. When the fracture resistance of an instrument in three different artificial canals was compared, the mean NCFs decreased as the radius of the curvature of the canal decreased from 8 to 2 mm. Manufacturing method is one of the most important factors on cyclic fatigue resistance, also the radius of curvature effects the cyclic fatigue.     

Numerical investigation of heat transfer and pressure drop in enhanced tubes

This study investigates passive heat transfer enhancement techniques to determine the distribution of temperature and static pressure in test tubes, the friction factor, the heat flux, the temperature difference between the inlet and outlet fluid temperatures, the pressure drop penalty and the numerical convective heat transfer coefficient, and then compares the results to the experimental data of Zdaniuk et al. It predicts the single-phase friction factors for the smooth and enhanced tubes by means of the empirical correlations of Blasius and Zdaniuk et al. This study performed calculations on a smooth tube and two helically finned tubes with different geometric parameters also used in the analyses of Zdaniuk et al. It also performed calculations on two corrugated tubes in the simulation study. In Zdaniuk et al.'s experimental setup, the horizontal test section was a 2.74 m long countercurrent flow double tube heat exchanger with the fluid of water flowing in the inner copper tube (15.57–15.64 mm i.d.) and cooling water flowing in the annulus (31.75 mm i.d.). Their test runs were performed at a temperature around 20 °C for cold water flowing in the annulus while Reynolds numbers ranged from 12,000 to 57,000 for the water flowing in the inner tube. A single-phase numerical model having three-dimensional equations is employed with either constant or temperature dependent properties to study the hydrodynamics and thermal behaviors of the flow. The temperature contours are presented for inlet, outlet and fully developed regions of the tube. The variations of the fluid temperature and static pressure along tube length are shown in the paper. The results obtained from a numerical analysis for the helically tubes were validated by various friction factor correlations, such as those found by Blasius and Zdaniuk et al. Then, numerical results were obtained for the two corrugated tubes as a simulation study. The present study found that the average deviation is less than 5% for the friction factors obtained by the Fluent CFD program while Blasius's correlation has the average deviation of less than 10%. The corrugated tubes have a higher heat transfer coefficient than smooth tubes but a lower coefficient than helically finned tubes. The paper also investigates the pressure drop penalty for the heat transfer enhancement.     

Effect of saliva contamination on shear bond strength and microleakage of one-bottle etch-and-rinse and self-etch adhesives: scanning electron and confocal laser microscopic analyses

Purpose: To evaluate the effect of saliva contamination on shear bond strength, microleakage, and microstructure of the adhesive interface in two different adhesive systems by using scanning electron microscopy (SEM) and confocal laser microscopy (CLSM). Materials and methods: Randomly, 228 third molars were allocated to six groups for an etch-and-rinse adhesive One-Step Plus (Bisco Inc.) and a self-etch adhesive G Bond (GC Corp.): Group 1 – manufacturer’s instructions were followed; Group 2 – involved contamination and drying before adhesive application; Group 3 – involved contamination, washing, and blot drying before adhesive application; Group 4 – involved contamination, etching, washing, and blot drying before adhesive application; Group 5 – involved contamination and drying after adhesive application, followed by adhesive reapplication; Group 6 – involved contamination and washing after adhesive application, followed by adhesive reapplication. Shear bond strength was tested after specimens were stored in distilled water at 37?°C for 24?h. Specimens were evaluated under a stereomicroscope for microleakage. Dentin–resin interfaces were evaluated by SEM and CLSM. Results: Group 2 for One-Step Plus and Group 3 for G Bond showed significantly lower bond strengths than control groups. Microleakage values were significantly greater at dentin than at enamel margins for all groups. In Group 2, for both adhesive systems, the highest microleakage was observed at dentin margins. Further, dentin–adhesive interfaces were not uniform and gaps were found by SEM and CLSM. Conclusions: The SEM and CLSM images demonstrated high variability of dentin–resin interfaces among saliva-contaminated groups. Rinsing the saliva and re-applying adhesive might be the best way to reduce the effect of saliva contamination on bond strength and microleakage.     

Performance analysis of drying of green olive in a tray dryer

This paper deals with the performance evaluation of a single layer drying process of green olives in a tray dryer using exergy analysis method. Green olive was used as the test material being dried. Drying process was realized at four different drying air temperatures (40, 50, 60 and 70 °C) and a constant relative humidity of 15%. The effects of temperatures and mass flow rates were investigated. Maximum exergy efficiency of the drying chamber was obtained at a temperature of 70 °C and a drying air mass flow rate of 0.015 kg/s with 0.0004 kg/s of olive. The exergy efficiency values were found to be in the range of 68.65%–91.79% from 40 °C to 70 °C with drying air mass flow rates of 0.01 kg/s–0.015 kg/s.