Performance evaluation of a triple‐effect evaporator with forward feed using exergy analysis

The present study evaluates the performance of a triple‐effect evaporator with forward feed (TEEFF) system by using exergy analysis based on actual operational data. The orange juice with a capacity of about 1.222 kg s^?1 is concentrated from a dry matter (DM) content of 12 to 65% in this TEEFF, which is situated in an orange juice concentrate line installed in a factory, located in Denizli, Turkey. A Visual Basic 6.0 program was also developed to show how the exergetic performance characteristics of the system vary with the feed flow rates ranging from 1.222 to 1.667 kg s^?1. The total exergy efficiency of the TEEEFF is found to be on average 0.85. The largest exergy destruction occurs in the first‐effect of the TEEFF system with 48.2% of total, followed by the third and second effects with 32.04 and 19.76% of that. Evaporator performance is also rated on the basis of steam economy, which is obtained to be in the range of 2.05–2.14 under the operation conditions. It is expected that the analysis presented here should provide a designer with a better, quantitative grasp of the inefficiencies and their relative magnitudes in the design, simulation and operation of multiple‐effect evaporators. Copyright © 2005 John Wiley & Sons, Ltd.     

Analysis of voltage and frequency-dependent series resistance and interface states of Al/ZnCo2O4: Gelatin/n-Si diode

Journal of Materials Science: Materials in Electronics - In this work, which aims to investigate the capacitance and conductance properties of ZnCo2O4-doped Gelatin, 5% ZnCo2O4-doped Gelatin film...     

The effect of Er:YAG laser and bulk filled composite type on marginal adaptation of class II cavities: an SEM analysis study

Purpose: To evaluate the effect of cavity preparation method (Er:YAG laser or diamond bur) and bulk-filled composite material type on marginal adaptation mesial occlusal (MO) class II cavities. Materials and Methods: Two-surface box cavities (4-mm proximal depth and 5-mm occlusal width) were prepared on 60 human mandibular molar teeth. Cavities were prepared using Er:YAG laser or diamond burs in an air-turbine hand-piece. All cavities were applied Single Bond Universal dentin bonding agent. The cavities were further subdivided into three subgroups according to the restorative material used; two bulk-filled composites [Filtek Bulk Fill Posterior (3M ESPE) and SonicFill 2 (Kerr)] and one traditional composite material Filtek Ultimate Universal Restorative (3M ESPE). Restorations were evaluated using scanning electron microscopy at ×200 magnification for their adaptation to the approximal margins of the tooth. Results were analyzed using the two-way ANOVA and Tukey Post Hoc Test (p < 0.05). Results: A total of 900 SEM figures were obtained from all groups. Filtek Bulk Fill Posterior, SonicFill 2, and Filtek Ultimate Universal Restorative exhibited statistically similar gapped margins. However, the lowest scores of gapped margins were observed with SonicFill 2 (4.22%). Conclusions: Completely gap-free margins were not obtained with any of the tested materials. Bulk-fill composite materials showed similar marginal adapatation compared with standard composite. Marginal adaptation of Er:YAG laser prepared cavities was more irregular and had more gaps, but was statistically similar to diamond bur-prepared cavities.     

A mixed integer programming model for remanufacturing in reverse logistics environment

Recently, there has been a growing interest in reverse logistics due to environmental deterioration. Firms incorporate reverse flow to their systems for such reasons as ecological and economic factors, government regulations and social responsibilities. In this paper a new mixed integer mathematical model for a remanufacturing system, which includes both forward and reverse flows, is proposed and illustrated on a numerical example. The proposed model provides the optimal values of production and transportation quantities of manufactured and remanufactured products while solving the location problem of dissassembly, collection and distribution facilities. The model is validated by using a set of experimental data reflecting practical business situation. Sensitivity analysis of the model is also presented.     

Fuel consumption and emission comparison of conventional and hydrogen feed vehicles

Current environmental concerns on nitrogen oxides (NO_x) and particulate matter (PM) emissions caused by diesel engines have led researchers to be interested in investigating vehicles with alternative power sources. Because of this reason, vehicle models with SI engine were adopted in the conducted study. Firstly, as an initial step, 1-D SI engine models were created with use of AVL Boost software. A four-cylinder engine model was created for conventional vehicle model, while a two-cylinder downsized engine was adopted as a subsystem of hybrid vehicle model. The models were based on experimental data obtained from a laboratory test setup with a single-cylinder engine. Subsequently, detailed engine maps on emissions and fuel consumption were generated with the developed ANN model. The fuel consumption and emission data, which were gathered from NEDC and WLTC simulations, were compared for conventional ICE, PEM FC and PEM FC + ICE powered vehicles with the help of the vehicle model which was developed by using Matlab Simulink software. Based on the results, it was concluded that there might be sufficient improvement in fuel consumption and significant improvement in emissions with the use of PEM FC that a hybrid driving system (PEM FC + ICE) can be utilized, and that emissions can be at 0 with the sole use of PEM FC.     

Influence of the ER,CR:YSGG laser and different irrigation methods on push-out bond strength of fiber post

Er,Cr:YSGG lasers are currently being investigated for disinfecting the root canal treatment. The aim of this study was to compare the effects of various irrigation protocols on push-out bond strength of fiber posts. Fifty maxillary anterior teeth were divided into five groups (n = 10) according to the protocol that applied into the post space. Group-1: distilled water, Group-2: 5% NaOCl, Group-3: 2% CHX, Group-4: Er,Cr:YSGG laser (1.5 W, 20 Hz, 85 air, 75 water, 26.7 J/cm²), Group-5: Er,Cr:YSGG laser (1.25 W, 50 Hz, 34 air, 24 water, 12.7 J/cm²). Fiber posts were cemented with resin cement. The remaining part of the root, three slices were obtained from each specimen and push-out test was performed. One-way ANOVA and Duncan’s test at a 5% level of significance were used for the statistical analysis. Post space irradiation with Er,Cr:YSGG laser (1.5 W 20 Hz, 85 air, 75 water, 26.7 J/cm²) increases push-out bond strength of fiber post to root canal dentin. Further investigations are needed to establish and optimize ER,Cr:YSGG laser parameters to increase the push-out bond strength of fiber posts.     

Determination of Optimum Velocity for Various Nanofluids Flowing in a Double-Pipe Heat Exchanger

Piping is one of the most important issues in the cost of process factories. It is known that 80% of bought equipment cost or 20% of overhead capital can belong to piping cost in a fluid-process factory. Pipe diameter and therefore flow velocity strongly affect the existing value of the factory regarding the consumed electric energy and fitting cost of pipes, pumps, and valves. We give a detailed cost analysis model for the pure fluids of water, motor oil, glycerin, ammonia, methanol, ethanol, ethylene glycol, and propane and their nanofluid mixtures with Ti and TiO₂ particles in liquid phase flowing in the tube side of a double-pipe heat exchanger. Pressure drop and pumping power values increase with flow velocity but total cost values show an arc with it. The clear outcome is that there is a minimum cost value as a result of the analyses for each investigated fluids. Moreover, validation of the model is performed by plotting the calculated items in figures such as total heat transfer coefficient versus Reynolds number, pressure drop versus Reynolds number, and friction factor versus mass flow rate. Characteristics of the trend lines in these figures are seen as they should be.