Alignment of fluorescent molecules vapour-deposited on to highly oriented PTFE substrates

The alignment of six fluorescent materials (p-terphenyl, p-quaterphenyl, p-quinquephenyl, diphenylstilbene, 1,4-bis(2-methylstyryl)benzene, and 1,4-bis-2-(5-phenyloxazolyl)benzene) grown from the vapour phase on to friction-deposited, highly oriented poly(tetrafluoroethylene) (PTFE) films was studied. The dichroic ratio of the fluorescent films produced was determined by polarized spectroscopic fluorescence measurements, and the crystallographic orientation of these materials was determined by transmission electron microscopy. The measured dichroic ratios ranged from 1.7 for diphenylstilbene to 5.0 for the p-quaterphenyl film. Electron diffraction patterns revealed that five of the fluorescent materials grew epitaxially on the single crystal-like PTFE films, the fluorescent crystals adopting particular orientations with respect to the crystallographic planes of PTFE. On the other hand, crystals of 1,4-bis-2-(5-phenyloxazolyl) benzene aligned in a fibre pattern, apparently by a grapho-epitaxial mechanism.     

A broadband power meter calibration system in the frequency rangefrom 10 MHz to 40 GHz using a coaxial calorimeter

A broadband power meter calibration system based on a newly constructed coaxial calorimeter has been developed in the frequency region 10 MHz-40 GHz. The RF power is measured as the difference of DC power supplied to the calorimeter built-in heater in the RF load, when RF is turned off and on, holding an isothermal control between the RF load and a temperature reference. To minimize the error due to the adiabatic coaxial waveguide, we devised a new method utilizing its output port as a test port. The evaluations showed a calibration uncertainty of (0.28-2.2)% expressed by one standard deviation at the 1 mW level in the full band     

Generalized model of the quantization error-a unified approach

The effective resolution of AD converters is a crucial quantization quality parameter in modern instrumentation. A usual theoretical assumption about the quantized (training) signal is that it is a pure sine wave with a “zero” offset. This means that either the average value of the sine wave is equal to one of the threshold levels (quantizer without dead zone) or that it lies exactly in the middle of them (rounding quantizer). In the measurement technique this assumption is hardly fulfilled, and that is why we meet something intermediate between the above-mentioned hypothetical situations. Here we generalize the known results for “zero” offset to the case of unknown offset. A general problem of an arbitrary random offset distribution is considered first. Two important practical cases are then analyzed. The first one is an unknown and nonrandom offset (one-point distribution). The second one is a case of a uniform distribution of the offset (effect of dithering on quantizer input). In particular, the expected values and variances are derived and analyzed versus the offset and the number of quantizing levels. The results obtained are applied to the effective resolution measurement     

ERD facility for analysis of hydrogen and deuterium in solids

Hydrogen is the lightest element in nature, and so, its detection and quantitative analysis is difficult by the conventional methods utilized for other elements. In the recent years the technique of elastic recoil detection analysis (ERD) using 1–2 MeV He⁺ beam has been developed to quantitatively and simultaneously analyze hydrogen and its isotopes in solids. Such a facility has been set up using the 2 MeV Van-de-Graaff accelerator at IIT Kanpur. It facilitates H and D analysis in a material up to a depth of ∼ 1μm with a detection sensitivity of 0·1 at.% and depth resolution of about 300 ?. The application potential of this setup is illustrated by presenting the results of measurements performed on Al:H:D systems prepared by plasma source ion implantation and highT _c YBCO pellets exposed to humid atmosphere.     

Analysis of adhesive bonded composite lap joints with transverse stitching

The effect of transverse stitching on the stresses in the adhesive is investigated using an adhesive sandwich model with nonlinear adhesive properties and a transverse stitching model for adhesive bonded composite single-lap and double-lap joints. Numerical results indicate that, among all stitching parameters, thread pretension and stitch density have significant effect on the peel stresses in the adhesive; increase in the thread pretension and the stitch density leads to a decrease in peel stress in the adhesive, while an increase in other parameters generally results in a negligible reduction in peel stress. The effect of stitching was found to be negligible on the shear stresses in the adhesive. Thus it is concluded that stitching is effective for the joints where peel stresses are critical and ineffective for those where shear stresses are critical.     

Discussion of “an interpretation of the carbon redistribution process during aging of high-carbon martensite”

Y. OHMORI and I. TAMURA:Metall. Trans. A, 1992, vol. 23A,     

Crystal-chemical anomalies in nonsuperconducting PrBa2Cu3O7

Studies of the crystal chemistry of nonsuperconducting PrBa₂Cu₃O₇ indicate that this compound is strictly isostructural with its superconducting RBa₂Cu₃O₇ (R = Y, rare earth) analogs. Crystallographically, Pr is present in the trivalent state according to the structural trends exhibited by the RBa₂Cu₃O₇ series as a function of R³⁺ ionic radius. The sole structural anomaly attributable to the presence of Pr³⁺ in the YBa₂Cu₃O₇ structure is a next-next-nearest neighbor effect and consists of an unusually short axial Cu-O distance, i.e., a short bond length between the in-plane copper and the chain oxygen. The correlation of this anomaly with the nonmetallic/nonsuperconducting properties of PrBa₂Cu₃O₇ supports a variety of literature reports, both theoretical and experimental, suggesting that the apical oxygen in the YBa₂Cu₃O₇ structure plays a critical role in mediating the appearance of superconductivity. The mechanism by which the f-electrons in Pr³⁺ (f ²) interact with the Cu-O manifold to produce the nonmetallic behavior of PrBa₂Cu₃O₇ remains unknown; however, superconductivity is “turned back on” for Nd³⁺ (f ³), immediately next to Pr and just slightly smaller. Careful comparative studies of superconducting NdBa₂Cu₃O₇ and nonmetallic PrBa₂Cu₃O₇ are needed to elucidate the critical difference in the behavior of the f-electrons and may shed light on the fundamental mechanism of high-temperature superconductivity in copper oxides.     

Prolonged exposure to intravesical foreign body induces a giant calculus with attendant renal dysfunction

A 31-year-old man came to our hospital complaining of severe voiding pain. He had inserted a fishing line made of nylon into his urethra at the age of eighteen, which was unable to be taken out and had been left there for 13 years. Preoperative ultrasonogram showed severe bilateral hydronephrosis and the serum BUN and creatinine level were as high as 45.2 mg/dl and 4.8 mg/dl, respectively. A huge bladder stone was demonstrated in X-ray film, the patient was admitted and vesicolithotomy was performed. The size of the stone was 10.5 x 7.5 x 7.5 cm and the weight was 360 grams. The fishing line was found inside the stone and the length was over 3 meters. The serum BUN and creatinine level after the operation were still high as 28.4 mg/dl and 4.1 mg/dl, respectively, and they did not improve even after six months following.