Vinyl triazole carrying metal‐chelated beads for the reversible immobilization of glucoamylase

Poly(ethylene glycol dimethacrylate–1‐vinyl‐1,2,4‐triazole) [poly(EGDMA–VTAZ)] beads with an average diameter of 100–200 μm were obtained by the copolymerization of ethylene glycol dimethacrylate (EGDMA) with 1‐vinyl‐1,2,4‐triazole (VTAZ). The copolymer hydrogel bead composition was determined by elemental analysis and was found to contain 5 EGDMA monomer units for each VTAZ monomer unit. The poly(EGDMA–VTAZ) beads were characterized by swelling studies and scanning electron microscopy (SEM). The specific surface area of the poly(EGDMA–VTAZ) beads was found 65.8 m²/g. Cu²⁺ ions were chelated on the poly(EGDMA–VTAZ) beads. The Cu²⁺ loading was 82.6 μmol/g of support. Cu²⁺‐chelated poly(EGDMA–VTAZ) beads with a swelling ratio of 84% were used in the immobilization of Aspergillus niger glucoamylase in a batch system. The maximum glucoamylase adsorption capacity of the poly(EGDMA–VTAZ)–Cu²⁺ beads was 104 mg/g at pH 6.5. The adsorption isotherm of the poly(EGDMA–VTAZ)–Cu²⁺ beads fitted well with the Langmuir model. Adsorption kinetics data were tested with pseudo‐first‐ and second‐order models. The kinetic studies showed that the adsorption followed a pseudo‐second‐order reaction model. The Michaelis constant value for the immobilized glucoamylase (1.15 mg/mL) was higher than that for free glucoamylase (1.00 mg/mL). The maximum initial rate of the reaction values were 42.9 U/mg for the free enzyme and 33.3 U/mg for the immobilized enzyme. The optimum temperature for the immobilized preparation of poly(EGDMA–VTAZ)–Cu²⁺–glucoamylase was 65°C; this was 5°C higher than that of the free enzyme at 60°C. The glucoamylase adsorption capacity and adsorbed enzyme activity slightly decreased after 10 batch successive reactions; this demonstrated the usefulness of the enzyme‐loaded beads in biocatalytic applications. The storage stability was found to increase with immobilization. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

The extraction of lactic acid by emulsion type of liquid membranes using alamine 336 in escaid 100

The extraction of lactic acid from aqueous solutions through an emulsion liquid membrane containing Alamine 336 as carrier was investigated. The influence of mixing speed, diluent type, surfactant concentration, extractant concentration, feed solution pH, stripping concentration, phase ratio, and feed concentration were examined. Liquid membrane consists of a diluent (n‐heptane, toluene, kerosene, Escaid 100, and Escaid 200), a surfactant (Span 80) and an extractant (Alamine 336), and Na₂CO₃ were used as a stripping solution. It is possible to extract 91% of lactic acid from aqueous solutions using Alamine 336 in Escaid 100, as an extractant and a diluent respectively.     

Adsorption of selenite and selenate ions onto thiourea‐formaldehyde resin

In the present work, thiourea‐formaldehyde (TUF) chelating resin was synthesized and used in the adsorptions of selenite (SeO) and selenate (SeO) ions. The effects of initial acidity and initial selenium concentrations on the adsorptions were examined by batch technique. The synthesized resin was applied to the elemental analysis to determine its composition. FT‐IR spectra and SEM/EDS were also recorded before and after selenite adsorption. It was found that selenite and selenate ions were adsorbed onto TUF resin at strong acidic conditions (3–5M HCl). The adsorption capacities of the resin were calculated as 833.3 mg g^?1 TUF resin for selenite ions and 526.3 mg g^?1 TUF resin for selenate. All the adsorption data obtained for both selenite and selenate ions fitted well to the Langmuir isotherm. It was seen that the adsorption mechanisms in the both adsorptions were governed by the reduction of selenite or selenate to elemental selenium, Se⁰. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Preparation and characterization study on maleic acid cross-linked poly(vinyl alcohol)/chitin/nanocellulose composites

In the quest on improving composite formulations for environmental sustainability, maleic acid (MA) cross-linked poly(vinyl alcohol) (PVA)-α-chitin composites reinforced by oil palm empty fruit bunch fibers (OPEFB)-derived nanocellulose crystals (NCC) had been successfully prepared. Based on the Fourier transform infrared (FTIR) spectroscopic analysis, it was proven that molecular interactions of the cross-linker to the polymeric networks was through conjugated ester linkage. Differential scanning calorimetry (DSC) showed that the influence of MA was minimal toward crystallization in the PVA/chitin/NCC composite. Maximum tensile strength, elongation at break and Young's modulus of the respective PVA/chitin/NCC composites were achieved at different content of MA, dependent on the PVA/chitin mass ratio. Among all compositions, a maximum Young's modulus was achieved at 30 wt% MA loading in PVA/chitin-30/NCC, amounting to 2,413.81 ± 167.36 MPa. Moreover, the mechanical properties and selected physicochemical properties (swelling, gel content, and contact angle) of the PVA/chitin/NCC composites could be tailored by varying the chitin content (10–30 wt%) and MA content (10–50 wt% based on total mass of composite). In brief, this chemically cross-linked PVA-based biocomposites formulated with sustainable resources exhibited tunable physicochemical and mechanical properties.     

Selective separation of cobalt and nickel by flat sheet supported liquid membrane using Alamine 300 as carrier

Cobalt and nickel are among the most important nonferrous metals. The using of flat sheet supported liquid membranes (FSSLMs) to remove metals from wastewaters has been used actively by the scientific and industrial communities. In this study, the selective separation of cobalt from thiocyanate solutions containing cobalt and nickel by FSSLM was examined using tri-n-octylamine (Alamine 300) as carrier. The FSSLM was consisted of extractant, flat sheet support and organic solvent. The various parameters were studied to determine the optimum extraction and striping conditions of cobalt and nickel. These parameters were stirring speeds of phases, NH₄SCN concentration, pH, diluent type, extractant concentration, stripping reagent concentration and modifier concentration. Concentration of cobalt and nickel were determined by Shimadzu AA-6701GF spectrophotometer. In the optimum conditions, selective separation of cobalt was achieved with an efficiency of 98.4% within 8 h, for equimolar feed mixtures, 400 mg/L Co + 400 mg/L Ni, and the separation factor of Co(II) over Ni(II) was 234.4. In addition, for nonequimolar feed mixtures, 500 mg/L Co + 1000 mg/L Ni, Ni in excess, selective separation of cobalt was 99.9%, and the separation factor of Co was 506 in the same time.     

Physiochemical Properties of <Emphasis Type="Italic">Jatropha curcas</Emphasis> Seed Oil from Different Origins and Candidate Plus Plants (CPPs)

The physicochemical properties of Jatropha seed oil from 9 geographical origins and 24 candidate plus plants (CPPs) were evaluated. The yield of seed oil obtained by Soxhlet extraction using n-hexane as solvent varied from 40.0% (Malaysia) to 48.4% (Vietnam) among seeds from different origins and 32.1% (CPP-17) to 48.8% (CPP-01) (w/w) among CPPs. Density, specific gravity, and refractive index of oil showed very little differences among all the seed sources. Oil from Borneo had the highest free fatty acid (FFA) content (2.3%) and a South African sample had the lowest FFA (0.4%), as oleic acids. Seed oil of CPP-13 had the highest FFA content (1.2%) and seed oil of CPP-17 the lowest (0.3%). Most of the CPPs in this study had an FFA content of less than 1%. Jatropha seed oil of Philippine origin had the highest iodine value (187.3 mg/g oil) and seed oil from Borneo the lowest (83.5 mg/g oil). The lowest saponification values were obtained from seed oil of Philippine origin (189.5 mg KOH/g) and CPP-22 (183.3 mg KOH/g oil) from Malaysia. The maximum higher heating value (40.3 MJ/kg) was obtained from seed oil from Borneo. The cetane numbers range from 25.4 (Indonesia) to 56.0 (Borneo) among the oils of base material and 46.4 (CPP-15) to 53.7 (CPP-06) among CPPs. This study gives basic information of relevance for biodiesel production using Jatropha seeds from various origins.     

The effects of cryogenic treatment on the toughness and tribological behaviors of eutectoid steel

Cryogenic treatment is a supplementary heat treatment usually applied after quenching. Its effects are permanent and this process affects the entire section. There have been many studies related to cryogenic treatment, most of which have been focused on tool steels. In the current study, a high-speed-train railway material was investigated, and different heat treatment processes were applied to the eutectoid steel. The effects of quenching and cryogenic treatment were investigated on the mechanical properties (toughness, hardness and wear). Four different structures were obtained with different heat treatment cycles: Pearlitic, tempered martensite, 12 hour cryo-treated tempered and 36 hour cryo-treated tempered. As a result of Charpy v-notch tests and hardness tests, cryogenic treatment was found to improve the toughness and hardness of quenched samples. The results of the ball-on-disc wear tests showed that the cryo-treated samples have better wear resistance than pearlitic and martensitic samples.     

Stress relaxation in carbon black loaded butyl rubber

The dependence of equilibrium force (F^*) on the strain ratio (α) of carbon black loaded butyl rubber was studied. The relation between elastic constant and volume fraction of carbon black was found in good agreement with that obtained by Guth and Gold relation at low concentrations using the shape factor (f = 6.5). The relaxation time and viscosity (η) were calculated by using stress relaxation of these samples at different compression strains. The same agreement was observed in the relation between viscosity and volume fraction of carbon black concentration. The results are discussed according to the dispersion mechanism of carbon black in rubber. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1067–1076, 2000     

Influence of hydrostatic pressure on the electrical properties of unvulcanized FEF-loaded SBR

Styrene butadience rubber (SBR-1502) loaded with different concentrations of FEF carbon black was tested to find out the effect of pressure on its electrical properties during vulcanization. Using the thermodynamically calculated values of the pressure coefficient (K), the thermoelastic coefficient (L = ?T/?P) was also estimated and compared with that obtained by other workers. The thermoelastic coefficient was found to be strongly dependent on the carbon black concentration.