Aluminum industry and climate change—Assessment and responses

It is now possible to assess the impact of the production processes of aluminum on the environment and to describe some of the ongoing responses and opportunities for improvement. This is compared with the benefits of aluminum in transportation, where the growing usage in various forms of transport due to its low density, high strength, and ability to be recycled enables reduced mass, increased fuel efficiency, reduced emissions and increased safety. It is the purpose of this paper to compare and contrast the emissions generated in the production of aluminum with the benefits accruing from its increased use in transportation.     

Growth of tin-doped indium antimonide for magnetoresistors

Magnetoresistors made from n-type indium antimonide are of interest for magnetic position sensing applications. In this study, tin-doped indium antimonide was grown by the metalorganic chemical vapor deposition technique using trimethylindium, trisdimethylaminoantimony, and tetraethyltin in a hydrogen ambient. Using a growth temperature of 370°C and a pressure of 200 Torr, it was found that the electron density in tin-doped films varied from 3.3×10¹⁶ cm⁻³ to 4.0×10¹⁷ cm⁻³ as the 5/3 ratio was varied from 4.8 to 6.8. From secondary ion mass spectroscopy (SIMS) studies, it was found that this variation is not caused by a change in site occupancy of the tin atoms from antimony to indium lattice sites, but rather to a change in the total tin concentration incorporated into the films. This dependence of tin incorporation on stoichiometry could be used to rapidly vary the doping level during growth. Undoped films grown under similar conditions had electron densities of about 2×10¹⁶ cm⁻³ and electron mobilities near 50,000 cm²V⁻¹s⁻¹ at room temperature for films that were only 1.5 μm thick on a gallium arsenide substrate. Attempts to grow indium antimonide at 280°C resulted in p-type material caused by carbon incorporation. The carbon concentration as measured with SIMS increased rapidly with increasing growth rate, to above 10¹⁹ cm⁻³ at 0.25 μm/h. This is apparently caused by incomplete pyrolysis of a reactant at this low growth temperature. Growth at 420°C resulted in rough surface morphologies. Finally, it was demonstrated that films with excellent electron mobility and an optimized doping profile for magnetoresistors can be grown.     

Solar cell efficiency tables (version 29)

Consolidated tables showing an extensive listing of the highest independently confirmed efficiencies for solar cells and modules are presented. Guidelines for inclusion of results into these tables are outlined and new entries since June 2006 are reviewed. Copyright © 2006 John Wiley & Sons, Ltd.     

Enhancing Photovoltaic Performance Using an All‐Conjugated Random Copolymer to Tailor Bulk and Interfacial Morphology of the P3HT:ICBA Active Layer

Bulk heterojunction (BHJ) solar cells are fabricated using active material blends of poly(3‐hexylthiophene) (P3HT) donor, indene‐C₆₀ bisadduct (ICBA) acceptor, and an all‐conjugated random copolymer (RCP) additive. By optimizing RCP loading, power conversion efficiencies (PCEs) up to 20% higher than those of a binary P3HT:ICBA mixture are achieved. The improved device characteristics are rationalized in terms of the differences between the photoactive thin film morphologies. Energy‐filtered transmission electron micro­scopy reveals that incorporation of the RCP improves the degree of structural order of the BHJ fibrillar network and increases the extent of microphase separation between P3HT and ICBA. Additionally, a combination of atomic force microscopy and X‐ray photoelectron spectroscopy analysis indicates segregation of the RCP at the free interface, leading to a shift in the surface potentials measured by Kelvin probe force microscopy. These changes, both in the bulk morphology and in the interfacial composition/energetics, are correlated to improved carrier collection efficiency due to a reduction of non‐geminate recombination, which is measured by charge extraction of photo­generated carriers by linearly increasing voltage.     

Dynamic laser control using feedback from a gain grating

We demonstrate that self-induced gain gratings can provide nonlinear optical feedback that results in single frequency selection and passive self Q-switching of a conventional linear laser cavity. An experimental Nd:YAG laser system is described that yields a temporally-smooth 20 ns pulse at 1.064 μm. In addition, we show that the feedback has phase-conjugate properties that permit “flower-like” mode formation even though the azimuthal symmetry of the cavity is broken     

Optical networking update

This paper presents an inventory of the current state and future prospects for networks in which signal paths between end user nodes remain entirely in optical form without intervening electronic conversions. The emphasis is on wavelength-division multiplexing (WDM). The applications and system aspects are stressed relative to details of the supporting technologies. The case to be made for optical networks as the basis of an entire possible future generation of networking is examined, after which the various architectural choices are discussed. Next, the limits on what can be achieved, mostly arising from limitations within the available technology, are treated. After a review of the history of all-optical networking, the paper concludes with speculations about where the applications, the technology and the architectural character of these systems will be going in the years ahead     

Performance characteristics of a compact position-sensitive LSO detector module

We assembled a compact detector module comprised of an array of small, individual crystals of lutetium oxyorthosilicate:Ce (LSO) coupled directly to a miniature, metal-can, position-sensitive photomultiplier tube (PSPMT). We exposed this module to sources of 511-keV annihilation radiation and beams of 30- and 140-keV photons and measured spatial linearity; spatial variations in module gain, energy resolution, and event positioning; coincidence timing; the accuracy and sensitivity of identifying the crystal-of-first-interaction at 511 keV; and the effects of intercrystal scatter and LSO background radioactivity. The results suggest that this scintillator/phototube combination should be highly effective in the coincidence mode and can be used, with some limitations, to image relatively low-energy single photon emitters. Photons that are completely absorbed on their first interaction at 511 keV are positioned by the module at the center of a crystal. Intercrystal scatter events, even those that lead to total absorption of the incident photon, are placed by the module in a regular "connect-the-dot" pattern that joins crystal centers. As a result, the accuracy of event positioning can be made to exceed 90%, though at significantly reduced sensitivity, by retaining only events that occur within small regions-of-interest around each crystal center and rejecting events that occur outside these regions in the connect-the-dot pattern.     

Revised test that a distribution is new better than used

The modified test of NBU-ness given by Green and Tiwari (1) related to more general null and alternative hypotheses than the corresponding test given by Hollander and Proschan (2). The Green and Tiwari test used an upper bound for the basic of the basic criterion, resulting in the test not being very powerful. In this revised test, suitable estimate of the variance is used instead of an upper bound. This is appropriate because a large sample size is assumed. The resulting test is more powerful than the earlier Green-Tiwari test, and more generally applicable than the Hollander-Proschan test.     

Testing that a distribution is new better than used of age to

Hollander and Proschan (1972) gave a test of NBU-ness of a distribution F, but it was pointed out by Green and Tiwari (1989) that the test more appropriately related to much wider null and alternative hypotheses than those stated, and provided suitable critical values. Similarly, Hollander, Park and Proschan (1986) later provided a test that a distribution is NBU-t_o and a modified test was given by Ebrahimi and Habibullah (1990). However, a similar criticism may be levelled against these tests and a modified test is here provided for appropriate, more general, hypotheses.