A single-chip storage LSI for home networks

Network direct attached storage (NDAS) is a network storage architecture that allows direct attachment of existing ATA/ATAPI devices to Ethernet without a separate server. Unlike other architectures such as NAS, SAN, and USB mass storage, no server computer intervenes between the storage and the client hosts. We describe an NDAS disk controller (NDC) amenable to low-cost single-chip implementation that processes a simplified L3/L4 protocol and converts commands between ATA/ATAPI and Ethernet, while the remaining complex tasks are performed by remote hosts. Unlike NAS architectures that use TCP/IP, NDAS uses a TCP-like lean protocol that lends itself well to high-performance hardware realization. Thanks to the simple NDAS architecture and protocol, an NDC implemented on a single 4 mm /spl times/ 4 mm chip in 0.18 /spl mu/m CMOS technology achieves a maximum throughput of 55 Mbytes/s on gigabit Ethernet, which is comparable to that of a high-performance disk locally attached to a host computer.     

Modeling and optimization of fringe capacitance of nanoscale DGMOS devices

We analyze the impact of gate electrode thickness and gate underlap on the fringe capacitance of nanoscale double-gate MOS (DGMOS) transistors. We propose an analytical fringe capacitance model considering gate underlap and finite source/drain length. A comparison with the simulation results show that the model can accurately estimate the fringe capacitance of the device. We show that an optimum gate underlap can significantly reduce the fringe capacitance resulting in higher performance and lower power consumption. Also, the effects of process variation in gate underlap devices are discussed. Simulation results on a three-stage ring oscillator show that with optimum gate underlap 32% improvement in delay can be achieved.     

Identification of microstructural zones and thermal cycles in a weldment of modified 9Cr-1Mo steel

This paper presents the results of a study on the microstructural and microchemical variations in a multipass Gas Tungsten Arc weld (GTAW) of modified 9Cr-1Mo steel. The changes brought about in the steel due to the heating and cooling cycles during welding and the subsequent effects due to reheating effects during multipass welding are described. Detailed analytical transmission electron microscopy has been carried to study the type and composition of the primary and secondary phases in this steel. The systematic changes in microstructural parameters such as Prior Austenite Grain Size, martensite lath size, number density, size and microchemistry of carbides, have been understood based on the different transformations that the steel undergoes during the heating and cooling process. Based on the observed microstructure, an attempt has been made to identify distinct microstructural zones and possible thermal cycles experienced by different regions of the weldment.     

组合斩波器为便携式应用增加带宽

对于精确地放大非常小的信号，简单的斩波放大器很适用，不过带宽有限。通过“组合“一个斩波器，带宽就能增加，使斩波器在更多的便携式设备中都有用武之地。     

Parallel path consistency

Filtering algorithms are well accepted as a means of speeding up the solution of the consistent labeling problem (CLP). Despite the fact that path consistency does a better job of filtering than arc consistency, AC is still the preferred technique because it has a much lower time complexity. We are implementing parallel path consistency algorithms on multiprocessors and comparing their performance to the best sequential and parallel arc consistency algorithms.^(1,2) (See also work by Kerethoet al. ⁽³⁾ and Kasif⁽⁴⁾) Preliminary work has shown linear performance increases for parallelized path consistency and also shown that in many cases performance is significantly better than the theoretical worst case. These two results lead us to believe that parallel path consistency may be a superior filtering technique. Finally, we have implemented path consistency as an outer product computation and have obtained good results (e.g., linear speedup on a 64K-node Connection Machine 2).     

Nanostructured polymer blends: Synthesis and structure

Nanostructured polymer blends prepared via anionic ring opening polymerizations of cyclic monomers in the presence of a pre-made polymer melt exhibit a number of special properties over traditional polymer blends and homopolymers. Here, we report on a simple and versatile method of in situ polymerization of macrocyclic carbonates in the presence of a maleic anhydride polypropylene (mPP) matrix and a surface-active compatibilizer (i.e. PC grafted onto a mPP backbone generated in situ) to yield a micro- and nanostructured polymer blends consisting of a polycarbonate (PC) minor phase, and a polypropylene (PP) major phase. By varying the processing conditions and concentration of the macrocyclic carbonate it was possible to reduce the size of the PC dispersions to an average minor diameter of 150 nm. NMR and TEM characterizations indicate that the PC dispersions do not influence crystal content in the PP phase. Overall, the results point to a simple strategy and versatile route to new polymeric materials with enhanced benefits.     

The treatment of waste-air containing mixed solvent using a biofilter 2. Treatment of waste-air containing ethanol and toluene in a biofilter

An experiment for five stages of a biofilter-run was performed to investigate the effect of hydrophilic ethanol and hydrophobic toluene on the biodegradation of hydrophobic toluene and hydrophilic ethanol, respectively, when waste-air containing toluene and ethanol was treated by a biofilter. Removal efficiencies of toluene and ethanol began to decrease when inlet load surpassed 90 g/m³/h and 100 g/m³/h consistent with maximum elimination capacities of toluene and ethanol, respectively. At the end of the biofilter-run, removal efficiencies for toluene and ethanol were decreased and maintained at 65% and 40%, respectively. The concentration of toluene at 1st sampling port was raised by factor of two in the 3rd stage of the biofilter run when the inlet load of ethanol co-feed was increased by 1.5 times, while the process conditions of toluene were maintained the same as those of the 2nd stage of biofilter-run. According to the result of Mohseni and Allen, it may be interpreted that removal efficiency of hydrophobic toluene was affected by the presence of hydrophilic ethanol when high load of hydrophobic toluene was applied like that of the 1st sampling port of the biofilter. However it was not the case when a low load of hydrophobic toluene was applied like those of the 2nd, 3rd and 4th sampling ports since hydrophobicity of toluene is much less that of α-pinene. Thus, it may be suggested that biodegradation of hydrophobic VOC was interfered by hydrophilic VOC dissolved in the biolayer and the degree of interference was proportional to the inlet load of hydrophobic VOC as well as that of hydrophilic VOC and was inversely proportional to the solubility of hydrophobic VOC. However, it was inferred that the existence of hydrophobic toluene from waste-air can hardly inversely hinder the removal of hydrophilic ethanol in the biofilter when timeevolutions of hydrophilic ethanol concentrations of this experiment were compared with those of the previous experiment of biofilter to treat waste-air containing ethanol only.