Adaptational changes in cellular fatty acid branching and unsaturation of Aeromonas species as a response to growth temperature and salinity

The effects of growth temperature and salinity on the cellular fatty acids were investigated on Aeromonas caviae, Aeromonas hydrophila and Aeromonas sobria. Under optimal growth conditions, fatty acids patterns were dominated by even-numbered chains C(16:0), C(16:1cis9), C(18:1cis11), C(12:0) and C(14:0). Growth temperature modifications induced, in the three Aeromonas species, important changes in fatty acid (i) unsaturation, (ii) branching and (iii) chain length. An important decrease in the C(18:1cis11) fatty acid content was observed for the three species below 15 degrees C and above 25 degrees C. The evolution of C(18:1cis11) and C(16:0) showed a mirror image for the three Aeromonas species. Low NaCl concentrations did not elicit significant changes in the fatty acids content of the three Aeromonas species. However, for high NaCl concentration in the medium, the growth ability was related to an important decrease of the unsaturated to saturated fatty acids ratio indicating a membrane rigidification. Thermal and salinity adaptations were branched fatty acid-dependent for A. caviae, whereas this phenomenon was less significant for A. hydrophila and A. sobria.     

Oregano: chemical analysis and evaluation of its antimalarial, antioxidant, and cytotoxic activities

Abstract: GC‐FID and GC‐MS analysis of essential oil from oregano leaves (Origanum compactum) resulted in the identification of 46 compounds, representing more than 98% of the total composition. Carvacrol was the predominant compound (36.46%), followed by thymol (29.74%) and p‐cymene (24.31%). Serial extractions with petroleum ether, ethyl acetate, ethanol, and water were performed on aerials parts of Origanum compactum. In these extracts, different chemical families were characterized: polyphenols (gallic acid equivalent 21.2 to 858.3 g/kg), tannins (catechin equivalent 12.4 to 510.3 g/kg), anthocyanins (cyanidin equivalent 0.38 to 5.63 mg/kg), and flavonoids (quercetin equivalent 14.5 to 54.7 g/kg). The samples (essential oil and extracts) were subjected to a screening for antioxidant (DPPH and ABTS assays) and antimalarial activities and against human breast cancer cells. The essential oil showed a higher antioxidant activity with an IC₅₀= 2 ± 0.1 mg/L. Among the extracts, the aqueous extract had the highest antioxidant activity with an IC₅₀= 4.8 ± 0.2 mg/L (DPPH assay). Concerning antimalarial activity, Origanum compactum essential oil and ethyl acetate extract showed the best results with an IC₅₀ of 34 and 33 mg/mL, respectively. In addition, ethyl acetate extract (30 mg/L) and ethanol extract (56 mg/L) showed activity against human breast cancer cells (MCF7). The oregano essential oil was considered to be nontoxic.     

From Powders to Thermally Sprayed Coatings

Since the early stages of thermal spray, it has been recognized that the powder composition, size distribution, shape, mass density, mechanical resistance, components distribution for composite particles play a key role in coating microstructure and thermo mechanical properties. The principal characteristics of particles are strongly linked to the manufacturing process. Coatings also depend on the process used to spray particles and spray parameters. Many papers have been devoted to the relationships existing between coating properties and structures at different scales and manufacturing processes. In many conventional spray conditions resulting in micrometric structures, among the different parameters, good powder flow ability, and dense particles are important features. Thermal plasma treatment, especially by RF plasma, of particles, prepared by different manufacturing processes, allows achieving such properties and it is now developed at an industrial scale. Advantages and drawbacks of this process will be discussed. Another point, which will be approached, is the self-propagating high-temperature synthesis, depending very strongly upon the starting composite particle manufacturing. However, as everybody knows, “small is beautiful” and nano- or finely structured coatings are now extensively studied with spraying of: (i) very complex alloys containing multiple elements which exhibit a glass forming capability when cooled-down, their under-cooling temperature being below the glass transition temperature; (ii) conventional micrometer-sized particles (in the 30-90 μm range) made of agglomerated nanometer-sized particles; (iii) sub-micrometer- or nanometer-sized particles via a suspension in which also, instead of particles, stable sol of nanometer-sized particles can be introduced; and (iv) spray solutions of final material precursor. These different processes using plasma, HVOF or sometimes flame and also cold-gas spray will be discussed together with the production of nanometer-sized particles via the chemical reaction method or by a special type of milling: the cryogenic milling process often referred to as “cryomilling.”     

Al2O3-ZrO2 Finely Structured Multilayer Architectures from Suspension Plasma Spraying

Suspension plasma spraying (SPS) is an alternative to conventional atmospheric plasma spraying (APS) aiming at manufacturing thinner layers (i.e., 10-100 μm) due to the specific size of the feedstock particles, from a few tens of nanometers to a few micrometers. The staking of lamellae and particles, which present a diameter ranging from 0.1 to 2.0 μm and an average thickness from 20 to 300 nm, permits to manufacture finely structured layers. Moreover, it appears as a versatile process able to manufacture different coating architectures according to the operating parameters (suspension properties, injection configuration, plasma properties, spray distance, torch scan velocity, scanning step, etc.). However, the different parameters controlling the properties of the coating, and their interdependences, are not yet fully identified. Thus, the aim of this paper is, on the one hand, to better understand the influence of operating parameters on the coating manufacturing mechanisms (in particular, the plasma gas mixture effect) and, on the other hand, to produce Al₂O₃-ZrO₂ finely structured layers with large varieties of architectures. For this purpose, a simple theoretical model was used to describe the plasma torch operating conditions at the nozzle exit, based on experimental data (mass enthalpy, arc current intensity, thermophysical properties of plasma forming gases, etc.) and the influences of the spray parameters were determined by mean of the study of sizes and shapes of spray beads. The results enabled then to reach a better understanding of involved phenomena and their interactions on the final coating architectures permitting to manufacture several types of microstructures.     

Use of ARMA block processing for estimating stationary low-frequency electromechanical modes of power systems

Accurate knowledge of low-frequency electromechanical modes in power systems gives vital information about the stability of the system. Current techniques for estimating electromechanical modes are computationally intensive and rely on complex system models. This research complements model-based approaches and uses measurement-based techniques. This paper discusses the development of an autoregressive moving average (ARMA) block-processing technique to estimate these low-frequency electromechanical modes from measured ambient power system data without requiring a disturbance. This technique is applied to simulated data containing a stationary low-frequency mode generated from a 19-machine test model. The frequency and damping factor of the estimated modes are compared with the actual modes for various block sizes. This technique is also applied to 35-min blocks of actual ambient power system data before and after a disturbance and compared to results from Prony analysis on the ringdown from the disturbance.     

Distributed control of nonlinear diffusion systems by input–output linearization

This paper addresses the distributed control by input–output linearization of a nonlinear diffusion equation that describes a particular but important class of distributed parameter systems. Both manipulated and controlled variables are assumed to be distributed in space. The control law is designed using the concept of characteristic index from geometric control by using directly the PDE model without any approximation or reduction. The main idea consists in the control design in assuming an equivalent linear diffusion equation obtained by use of the Cole–Hopf transformation. This framework helps to demonstrate the closed‐loop stability using some concepts from the powerful semigroup theory. The performance of the proposed controller is successfully tested, through simulation, by considering a nonlinear heat conduction problem concerning the control of the temperature of a steel plate modeled by a nonlinear heat equation with Dirichlet boundary conditions. Copyright © 2012 John Wiley & Sons, Ltd.     

Formal Proofs of Rounding Error Bounds

Floating-point arithmetic is a very efficient solution to perform computations in the real field. However, it induces rounding errors making results computed in floating-point differ from what would be computed with reals. Although numerical analysis gives tools to bound such differences, the proofs involved can be painful, hence error prone. We thus investigate the ability of a proof assistant like Coq to mechanically check such proofs. We demonstrate two different results involving matrices, which are pervasive among numerical algorithms, and show that a large part of the development effort can be shared between them.