沈庭景胜 --2006年沈阳世界园艺博览会沈阳园设计

在沈阳园的设计中,设计师充分利用北方大环境的特征及基地中细微的高差、观视角度等元素突出沈阳地域特性.为了能将园林功能融入园林设计之中,设计师大量运用了欲扬先抑等手法.     

Effects of Thermal Cycle on Mechanical Properties and Fractography in HAZ of HQ130 Steel

The effect of different peak temperature (Tp) and cooling time (t8/5) on hardness, impact toughness and fracture morphology in the heat-affected zone (HAZ) of HQ130 steel was studied by using welding thermo-simulation test. Experimental results show that the impact toughness and hardness decrease with the decrease of Tp or increase of t8/5 under the condition of a single thermal cycle. There is a brittle zone in the vicinity of Tp=800℃, where the impact toughness is considerably low. There is softened zone in vicinity of Tp=700℃, Where the hardness decreases but the toughness increases. In the practical application of multi-layer and multi-pass welding, the welding heat input should be strictly limited (t8/5≥20s) so as to reduce the softness and brittleness in the HAZ of HQ130 steel.     

Electrochemical properties of Mg-based alloys containing carbon nanotubes

In this work, effects of partial substitution of Mg, Ni with AB₂ in Mg-based alloy and subsequent surface modification by further ball-milling with carbon nanotubes (CNTs) on electrochemical properties were investigated. Mg_1.9(AB₂)_0.1Ni_0.8 (AB₂=LaNi₂, LaNiCo and LaNiMn) alloys were prepared by solid-state diffusion method, the nanocrystalline Mg-based alloys were prepared by ball-milling the mixture of obtained Mg_1.9(AB₂)_0.1Ni_0.8 alloys and nickel powder. It was found that the electrochemical capacities of nanocrystalline Mg_1.9(AB₂)_0.1Ni_1.8 alloys were measured to be 460–490 mAh/g. The nanocrystalline Mg-based alloys containing carbon nanotubes (10 wt.%) obtained by ball-milling after 60 min were demonstrated to show improved electrochemical properties with respect to the original nanocrystalline Mg-based alloys. The electrochemical reaction activity was detected by electrochemical impedance spectra (EIS). Raman and X-ray photoelectron spectroscopy (XPS) proved the interaction between Mg_1.9(AB₂)_0.1Ni_1.8 alloys and carbon nanotubes after ball-milling, which resulted in an increase in the surface Ni/Mg ratio.     

低VOC低成膜温度水性聚氨酯分散体的合成与表征

以环氧树脂、甲基丙烯酸甲酯(MMA)和丙烯酸羟丙酯(HPA)复合改性水性聚氨酯(WPU),制得以丙烯酸酯为核,聚氨酯为壳,HPA为核壳之间桥连的核壳交联型PUA复合乳液。实验研究结果表明:这种复合乳液可以达到较高硬度漆膜(1H以上),最低成膜温度(2～5℃左右)。MMA添加量增大,涂膜硬度、耐水性逐渐提高,乳液的稳定性则随着降低。当MMA含量为20%左右时综合性能较好。     

EVA对PP/EVA共混物力学性能的影响

将不同配比的聚丙烯(PP)和乙烯-乙酸乙烯共聚物(EVA)进行共混,测试了共混物的拉伸强度和冲击强度;用差示扫描量热法研究了共混物的结晶性能;用扫描电镜(SEM)二次电子成像系统分析了试样的断口形貌,研究了EVA含量对共混物力学性能的影响。结果表明:EVA的加入提高了EVA/PP共混体系的韧性,同时降低了PP的结晶度。     

聚甲醛/共聚酰胺共混物的结晶形态及力学性能

研究了共聚酰胺含量对聚甲醛/共聚酰胺(POM/COPA)共混物结晶形态及力学性能的影响。结果表明:POM/COPA共混物中存在氢键相互作用;结晶温度对POM的结晶形态有较大影响,温度较高时POM结晶较完善,球晶尺寸较大;同时,COPA的加入使共混物的球晶细化,极大地改善了POM的韧性。当COPA含量为4%时,共混物缺口冲击强度达到最大值,拉伸强度几乎不变,POM/COPA具有较理想的综合力学性能。     

单螺杆混沌挤出过程周期性行为数值模拟

建立了混沌单螺杆挤出机计量段物理和数学模型。定义了更合理的边界条件,采用Carreau本构方程,采用有限体积方法对聚合物熔体在螺槽内流动的周期性效应进行了数值模拟分析。得到了不同位置的速度分布细节以及流体示踪粒子的行为轨迹。发现螺槽内速度分布表现出周期性和对称性的变化,揭示了同宿点及椭圆点存在及位置不变性,为进一步分析流体质点在相空间的动力学行为奠定了基础。     

动态三螺杆挤出机制备热塑性硫化胶的研究

对比分析了动态热塑性硫化胶(TPV)的加工设备,着重介绍了附加振动力场的三螺杆反应挤出机的结构特点以及利用该机进行三元乙丙橡胶/聚丙烯(EPDM/PP)的动态全硫化,对制品的物理力学性能和微观结构分别进行了测试分析和电镜扫描。结果表明,振动力场作用下EPDM/PP共混体系反应挤出动态硫化加工可有效地实现动态硫化反应、硫化橡胶的粉碎和分散以及相态反转,振动力场的作用明显提高了TPV性能。     

静高压作用下纯铝凝固过程温度场的数值模拟

采用数值模拟的方法,研究了纯铝在静高压作用下凝固过程温度场的变化情况。首先建立了温度场的数学模型,根据压力与金属熔点的关系,将压力作用到凝固过程的温度场上。模拟结果表明:压力越大,纯Al开始凝固的时间越早;在凝固过程中,压力越大,对应的温度变化速度越快。     

电磁动态金属粉末注射成型型坯结构性能的研究

利用自行设计的电磁动态注射机DPII-90，对不锈钢金属粉末316L和粘结剂的混合喂料进行稳态和动态注塑成型实验，研究振动参数对金属粉末和粘结剂混合喂料的均匀化和密实机理的影响。实验结果表明，各动态成型条件下的型坯密度明显大于稳态成型条件下的密度。当振动频率（或振幅）不变时，随着振幅（频率）的增大，型坯密度呈非线性增大，达到最大值后缓慢下降，存在一个最佳值。在频率7Hz-10Hz，振幅50μm～150μm的范围内，注射出的型坯密度较高，密实性好。电镜扫描（SEM）发现，金属粉末与粘结剂的分散均匀和完善程度的变化规律和型坯密度随着振幅（频率）的变化规律基本一致。