A small-angle X-ray scattering study of powder compaction

This work demonstrated a novel and potentially important application of two-dimensional small-angle X-ray scattering (2D-SAXS) to investigate powder compaction. SAXS from powder compacts of three materials commonly used for pharmaceutical tabletting exhibited azimuthal variations, with stronger intensity in the direction of the applied compaction force, relative to the transverse direction. This implied that compaction of a (macroscopic) powder could also produce changes on the molecular (nanometre) scale, which can be probed by 2D-SAXS. Two possible explanations for this effect were suggested. A combination of anisometric (i.e. elongated or flattened) granules with anisotropic morphologies could result in azimuthal variation in X-ray scattering due to granule orientation. It is expected that this mechanism would require relatively low packing density, so may operate during die filling. Granule re-orientation appeared less likely at higher packing densities and compaction pressures, however. Under these conditions, the changes in the 2D-SAXS patterns would be consistent with the powder granules becoming relatively flattened in the compression direction, with corresponding changes in their nano-scale morphology. The magnitude of this effect was found to vary between the materials used and increased with compaction pressure. This suggested that 2D-SAXS studies could provide useful information on force-transmission within a compressed powder. Further analysis of the data also suggested differences in the compaction mechanisms (i.e. granule re-orientation, deformation or fragmentation) between the materials studied.     

On the determination of boundaries to manipulator workspaces

The accumulation of two independent, broadly applicable formulations for determining the boundary to manipulator workspaces, presented elsewhere, are compared in this paper. Insights gained from one method are used to explain behavior exhibited in the other. Results are also compared and validated. A numerical formulation based on continuation methods is used to map curves that are on the boundary of a manipulator workspace. Analytical criteria based on row rank deficiency criteria of the manipulator's analytical Jacobian are used to map a family of one-dimensional solution curves on the boundary. The other formulation, based on a similar rank-deficiency criteria, yields analytic boundaries parametrized in terms of surface patches on the boundary. Results concerning the applicability of the numerical method to open- and closed-loop systems are compared with those limited to the open-loop for the analytical method. Conclusions regarding the behavior of the manipulator on geometric entities characterized by singular curves, higher-order bifurcation points, and surfaces inside the workspace are drawn. Applicability of both methods and their limitations are also addressed.     

Novel technique for SiO2 formed by liquid-phasedeposition for low-temperature processed polysilicon TFT

A technique for SiO₂ formation by liquid-phase deposition (LPD) at nearly room temperature for low-temperature processed (LTP) polysilicon thin-film transistor (poly-Si TFT) was developed. LPD SiO₂ film with a lower P-etch rate shows a dense structure. LPD SiO₂ also exhibits good electrical characteristics. LTP poly-Si thin-film transistors (TFTs) with LPD SiO ₂ as the gate insulator have been fabricated and investigated. Their characteristics indicate performance adequate for their use as pixel transistors in liquid crystal displays (LCDs)     

Programmable group-delay module using binary polarization switching

We demonstrate the first programmable group-delay module based on polarization switching. With a unique binary tuning mechanism, the device can generate any differential group delay value from -45 to +45 ps with a resolution of 1.40 ps, or any true-time-delay value from 0 to 45 ps with a resolution of 0.7 ps. The delay varying speeds for both applications are under 1 ms and can be as fast as 0.1 ms. We evaluate both the dynamic and static performances of the device while paying special attention to its dynamic figures of merit for polarization-mode dispersion emulation and compensation applications. Our experiment shows that the device exhibits a negligible transient-effect induced power penalty (<0.2 dB) in a 10-Gb/s nonreturn-to-zero system.     

Indexed in current contents

Indexed in current contents     

Traffic grooming on WDM rings using optical burst transport

A sublambda traffic-grooming scheme on wavelength-division-multiplexed (WDM) rings, which is called optical burst transport (OBT), is proposed. The network protocol and architecture allow increased flexibility to tailor the transport network behavior for efficient delivery of bursty data traffic. Using different network parameters, its performance is analyzed via simulation, and the implementation issues including the media-access-control (MAC) protocol, tunable-filter controller, and burst-mode receiver are addressed. Finally, the feasibility of the OBT with an experimental testbed built by the authors is demonstrated and a streaming-video application is used to present its overall functionality.     

Process conditions for separating fatty acid esters by supercritical CO2

The solubilities of ethyl palmitate, ethyl oleate, ethyl eicosapentaenoate (EPA) and ethyl docosahexaenoate (DHA) in supercritical carbon dioxide were determined by a continuous flow method. The solubilities of fatty acid ethyl esters increased with pressure and decreased as the temperature was increased. An empirical equation, similar to Chrastil's equation, was used to describe the relationship between solute solubility and the density of carbon dioxide. The empirical equation was further used to qualitatively estimate the separation efficiency of isolating EPA and DHA ethyl esters from fatty acid esters. The operating conditions yielding high solubility gave fast extraction rate but resulted in low separation efficiency. Experiments were conducted to separate ethyl EPA and ethyl DHA from a model mixture containing four fatty acid ethyl esters and from esterified squid visceral oil. The experimental data compared closely with the calculated values.     

Organic‐acid‐catalyzed sol–gel route for preparing poly(methyl methacrylate)–silica hybrid materials

In this study, a series of organic–inorganic hybrid sol–gel materials consisting of a poly(methyl methacrylate) (PMMA) matrix and dispersed silica (SiO₂) particles were successfully prepared through an organic‐acid‐catalyzed sol–gel route with N‐methyl‐2‐pyrrolidone as the mixing solvent. The as‐synthesized PMMA–SiO₂ nanocomposites were subsequently characterized with Fourier transform infrared spectroscopy and transmission electron microscopy. The solid phase of organic camphor sulfonic acid was employed to catalyze the hydrolysis and condensation (i.e., sol–gel reactions) of tetraethyl orthosilicate in the PMMA matrix. The formation of the hybrid membranes was beneficial for the physical properties at low SiO₂ loadings, especially for enhanced mechanical strength and gas barrier properties, in comparison with the neat PMMA. The effects of material composition on the thermal stability, thermal conductivity, mechanical strength, molecular permeability, optical clarity, and surface morphology of the as‐prepared hybrid PMMA–SiO₂ nanocomposites in the form of membranes were investigated with thermogravimetric analysis, differential scanning calorimetry, dynamic mechanical analysis, gas permeability analysis, ultraviolet–visible transmission spectroscopy, and atomic force microscopy, respectively. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008