Kriterien für die Zulassung von Tierarzneimitteln gegen Zeckenbefall bei Hunden und Katzen: Ein Überblick der aktuellen Anforderungen und Möglichkeiten unter Berücksichtigung der derzeitig gültigen Leitlinien

Ohne Zusammenfassung The online version of the original article can be found under doi:.     

Modified CMA based blind multiuser equaliser with decision directed scheme

A modified constant modulus (CM) algorithm based blind multiuser equaliser with a decision directed (DD) scheme is developed that does not require any mutual decorrelation and is suitable for downlink direct sequence code division multiple access systems. The performance of the proposed time domain adaptive equaliser is evaluated with respect to usual parameters and is found to perform better than the concurrent CM algorithm and DD scheme.     

Investigation into Polarization of Unloaded and Loaded Microstrip Square-Ring Antennas

The polarization characteristic of unloaded and loaded square-ring microstrip antennas is investigated. Several different loading types like single-stub, dual-stub, notch, gap and shorting-pin are considered and their effects are studied. Loading enables feeding using a 50-Omega probe. The simulation and measurement results show that the loading techniques excite a loaded TMy ₁₁ mode that is orthogonal to the unloaded TMx ₁₁ mode. This indicates that by loading the ring antenna its polarization can be switched adaptively. However, the purity of the loaded and unloaded modes depends on the loading type. For some loading types like gap and shorting-pin, the excitation of the unloaded mode seems negligible, in comparison to the loadings by stub and notch. For the stub and notch loaded antennas the unloaded mode is also present, and its excitation efficiency is frequency dependent. Thus, their polarization plane, which is due to both loaded TMy ₁₁ and unloaded TMx ₁₁ modes, also becomes frequency dependant. The results of this investigation can be useful in selecting the loading methods for high-impedance microstrip ring antennas, and control of their impedance and polarization. The knowledge of the antenna polarization is essential in communications, and its dependence on the loading type can be used as an important parameter in design of adaptive antennas and sensors.     

Electrochemical mass transfer between an impinging jet and a rotating disk in a confined system

This paper presents the mass transfer results from an impinging liquid jet to a rotating disk. The mass transfer coefficients were measured using the electrochemical limiting diffusion current technique (ELDCT). Rotational Reynolds number (Re_r) in the range of 3.4 × 10⁴–1.2 × 10⁵, jet Reynolds number (Re_j) 1.7 × 10⁴–5.3 × 10⁴ and non-dimensional jet-to-disk spacing (H/d) 2–8 were taken into consideration as parameters. It was found that the jet impingement resulted in a substantial enhancement in the mass transfer compared to the case of the rotating disk without jet.     

Interval based MINLP superstructure synthesis of mass exchange networks

A new simultaneous synthesis approach for mass exchange networks (MENs) is presented. The technique is adapted from the interval based mixed integer non-linear program (MINLP) superstructure (IBMS) synthesis of heat exchanger networks (HENs). The superstructure interval boundary compositions are defined by the supply and target compositions of either the rich or lean set of streams. Each rich and lean stream in the superstructure has the potential of exchanging mass with streams of opposite kind in each interval based on mass transfer feasibility. The model harnesses the strengths of the stagewise superstructure and the pinch technology methods for mass exchange network synthesis (MENS). The IBMS approach simultaneously trades-off the capital and operating costs for MENs. The superstructure composition interval defining approach introduced in this paper enforces the mixing of split streams at equal compositions, hence there is no need to include mixing equations in the model. Fixing the interval boundaries helps to eliminate the complexities involved in initialisations, thus the region of search for the optimum solution is reduced. The IBMS model is applied to MENS problems involving continuous contact and staged columns. It is also extended to problems involving multiple mass separating agents (MSAs) and regeneration. The results obtained compare well with those in the literature.     

Comparative Study of Rubidium and Cesium as Promoters in Carbon-supported Ruthenium Catalysts for Ammonia Synthesis

Sibunit-supported Ru-catalysts promoted with cesium or rubidium compounds have been comparatively studied with XPS. The cesium promoter interacts both with support and with active component. The absence of the promoter–support interaction in the case of rubidium provides a stronger interaction between promoter and active component compared to the cesium-based catalysts. These differences in the promoter–support and promoter–metal interactions are exhibited when a sequence of ruthenium and alkali introduction are changed.     

Smart phones and interactive reports leave traffic in the rearview mirror

To convey the dynamic information related to traffic conditions in various parts of a city, we propose an environment utilizing the technology of smart phones to provide information anywhere and anytime. Called ";The Interactive Traffic Beat Project,"; it uses a Web-based service to deliver this information to people through their cell phones at the right time so that valuable time can be saved and the chaos on the roads can be managed.     

Terahertz imaging: materials and methods

Terahertz (THz) imaging is rapidly developing. We present two new methods, based respectively on (a) a broadband thermal source (globar) and (b) a coherent, monochromatic source (optically-pumped THz laser). A room-temperature detector (Golay cell) is employed. Image quality is similar to that reported by others using more complex sources (quantum cascade lasers) and detectors (superconducting tunneling junctions).     

Eigenspannungen als Messgröße zur Qualitätssicherung

Residual stress as measured quantity in quality assurance The x‐ray method is used in the Volkswagen Automotive Group at different world‐wide locations as a standard procedure to determine residual stress. As an important measured quantity in the quality assurance residual stresses are specified in drawings of different components (e.g. gears, coil springs). Measurements are carried out during quality assurance, production, damage analyse, technical development department and design control of components from suppliers. An optimum efficiency can be achieved, if it exists a unique correlation between residual stress values and loading capacity of components, and if the processes to introduce residual stress can be optimized using residual stress measurements during the production.