The morphology of rigid-rod polymers and molecular composites resulting from coagulation processing

The effects of processing conditions on the morphology of molecular composite films are examined by optical and electron microscopy. During coagulation processing from solutions in methanesulfonic acid (MSA), rigid-rod polymer, such as poly(p-phenylenebenzobisoxazole) (PBO), phase separates into undesirable aggregates. The coagulant and the method of its introduction have been found to exert a strong impact on the final film morphology. A quench of a PBO solution in MSA into a water bath results in a three dimensional interconnected network of PBO, while a slower introduction of water results in a more amorphous material. A computer simulation program of the coagulation process has been developed to better understand the different structures emerging from coagulation processing of molecular composites. The simulation results are in qualitative agreement with the experimental observations.     

Performance evaluation of a multichannel transceiver system forADSL and VHDSL services

The authors study the performance of a multichannel modulation method for asymmetric digital subscriber lines (ADSLs) and very high-speed digital subscriber lines (VHDSLs). In the ADSL case, over all unloaded North American subscriber lines in the test set, a unidirectional 1.536 Mb/s data rate service from the end office to the customer premises is possible on a single twisted pair at an error rate of 10^-7 with at least a 6 dB margin used coded multichannel modulation with sufficient transmit power. In the VHDSL case, data rates in excess of 100 Mb/s can be transmitted reliably, at an error rate of 10^-7, using uncoded multichannel modulation on a single twisted pair over a distance ⩽150 ft with a sufficiently high sampling rate (≈24 MHz) and transmit power. It is shown that a cost-effective multichannel transceiver design suggested for high-speed digital subscriber line (HDSL) service will also work well for ADSL and VHDSL services with only minimal modifications     

Probabilistic Wind Farms Generation Model for Reliability Studies Applied to Brazilian Sites

This paper presents a computer model for the probabilistic representation of wind farms generation for reliability studies, which can provide an annual estimation of energy production and calculate several performance indexes. The model combines the stochastic characteristics of wind speed with the operational information of the turbines, such as the failure and repair rates, representing the wind farm by a Markov process. The simulations are made with real time series of wind speed of several Brazilian regions and actual turbine models. The influence of some wind farm and installation site characteristics on the results are evaluated, such as the wind speed statistical clustering technique, the number and type of the turbines, and the failure and repair rates. The results obtained reproduce successfully the behavior of the components considered in the model     

New fault-location method for a single multiterminal transmission line using synchronized phasor measurements

This paper describes a new iterative method to locate a fault on a single multiterminal transmission line. The method uses synchronized voltage and current measurements from all terminals. Using positive-sequence components of the prefault and postfault waveforms, positive-sequence source impedances are estimated. Using these source impedances and the line data, the positive-sequence bus impedance matrix (Z/sub bus/) is formed. Using the properties of Z/sub bus/, an iterative algorithm is proposed. The algorithm first identifies the faulted section and then locates the fault on this section. This algorithm is applied to the data obtained from the Electromagnetic Transients Program simulation of a multiterminal transmission line. The simulation results show that the distinctive features of this method are that it performs with very high accuracy for all types of faults at different fault locations and is practically immune to fault resistance.     

Software architecture-centric methods and agile development

The agile software development paradigm and plan-driven approaches each have their strengths and shortcomings. The former emphasizes rapid, flexible development, while the latter emphasizes project and process infrastructure. Many practitioners, particularly of agile methods, tend-to view software architecture in light of the plan-driven side of the spectrum. They think that architecture-centric methods are too much work, equating them with high-ceremony processes emphasizing document production. But many elements make up a successful development approach, including process, product, technology, people, and tools. Software architecture is part of product quality and isn't tied to a particular process, technology, culture, or tool. This article explores the relationship and synergies between architecture-centric design and analysis methods and the extreme programming framework. We chose to focus on XP because it's one of the most mature and best-known agile practices.     

Long-term testing and applications of high-stress MV EPR cables

High-stress design 35-kV ethylene propylene rubber (EPR)-insulated cables with 1.14-mm (45-mil) wall reduction have been in service for more than ten years. In the mid 1990s, an extensive cable testing program was initiated to demonstrate that high-stress designs up to 4 kV/mm (101.6 V/mil) exhibit a significant electrical and mechanical safety margin to operate on typical utility network systems. Investigations were also undertaken to demonstrate the suitability of accessories for high-stress designs. This paper will present the results of six-year, long-term wet electrical testing conducted to demonstrate that with proper design, the aging performance of standard wall and high-stress design cables provide satisfactory results and suitable performance for the intended application. Additionally, utility field experience is presented on 35- and 15-kV cables operating at high stress. The experience for these 15-kV medium-voltage EPR cable designs employ the highest recommended stress for cables of this class, as well as taking into account the complete system performance.