桉木硫酸盐浆不同漂白技术的评价

高白度漂白商品浆的白度已从通常的88%～90%提高到更高的水平,达到92%.这种高白度的要求导致了纸厂使用高价格光学漂白剂,以及过量使用这种添加剂的环境风险.     

Effect of Thickness of the p-AlGaN Electron Blocking Layer on the Improvement of ESD Characteristics in GaN-Based LEDs

The following letter presents a study regarding GaN-based light-emitting diodes (LEDs) with p-type AlGaN electron blocking layers (EBLs) of different thicknesses. The study revealed that the LEDs could endure higher electrostatic discharge (ESD) levels as the thickness of the AlGaN EBL increased. The observed improvement in the ESD endurance ability could be attributed to the fact that the thickened p-AlGaN EBL may partly fill the dislocation-related pits that occur on the surface of the InGaN-GaN multiple-quantum well (MQW) and that are due to the strain and the low-temperature-growth process. If these dislocation-related pits are not partly suppressed, they will eventually result in numerous surface pits associated with threading dislocations that intersect the InGaN-GaN (MQW), thereby reducing the ESD endurance ability. The results of the experiment show that the ESD endurance voltages could increase from 1500 to 6000 V when the thickness of the p-AlGaN EBL in the GaN LEDs is increased from 32.5 to 130 nm, while the forward voltages and light output powers remained almost the same.     

维拉诺瓦巴奎因城市公园

维拉诺瓦巴奎因城市公园坐落在里斯本市区，倚靠葡萄牙最长的河流——塔古斯河的右岸。在塔古斯河谷的大型综合项目中，包含了对这片10hm^2土地的改造，以重新评估它的城市和景观价值。     

烧结成品运输自动控制系统的改进

对烧结成品运输自控系统不稳定性因素进行了分析，提出了采取优化硬件外围工作环境，完善软件保护程序等改进措施。改进后的自控系统稳定性明显提高。     

分置式牛津型斯特林制冷机的数值分析与实验验证

对分置式牛津型斯特林制冷机进行了数值计算 ,介绍了计算模型考虑到的众多不可逆因素。通过对计算结果与实验结果的对比 ,验证了本文数值计算的准确性 ,说明本文计算模型与数值处理方法是切实可行的     

Effect of deformation route on microstructural development in aluminum processed by equal channel angular extrusion

Aluminum has been deformed by equal channel angular extrusion (ECAE) to obtain submicron-grained structures under different deformation routes. The deformation routes were varied by rotating billets through 0, 90, and 180 deg between each extrusion pass, and were designated as route A, B_C, and C, respectively. Based on quantitative microstructural analysis, the effectiveness of the deformation route is shown to depend upon the different definition used. The order of effectiveness is (a) A > B_C > C for both 90 and 120 deg dies, in terms of the generation of high-angle grain boundaries (HAGBs); (b) B_C > C > A for both 90 and 120 deg dies, in terms of the formation of equiaxed shape of grains; and (c) B_C > A > C for 90 deg die and B_C ∼ A > C for 120 die, in terms of reducing grain size. It is suggested that the generation of HAGBs can be related to the accumulation of nonredundant strain, while the shape and orientation of grains may be linked to the shearing patterns of the deformation route.     

Approach for Overcoming Numerical Inaccuracy Caused by Load Discontinuity

It was found that the discontinuity at the end of an impulse will lead to numerical inaccuracy as this discontinuity will result in an extra impulse and thus an extra displacement in the time history analysis. In addition, this extra impulse is proportional to the discontinuity value at the end of the impulse and the size of integration time step. To overcome this difficulty, an effective approach is proposed to reduce the extra impulse and hence the extra displacement. In fact, the novel approach proposed in this paper is to perform a single small time step immediately upon the termination of applied impulse, whereas other time steps can be conducted by using the step size determined from accuracy consideration in period. The feasibility of this approach is analytically explored. Further, analytical results are confirmed by numerical examples. Numerical studies also show that this approach can be applied to other step-by-step integration methods. It seems that to slightly complicate the programming of dynamic analysis codes is the only disadvantage of this approach.     

一种发出红色荧光的六核配合物[Cu6（pymt）6]

合成了一价铜和2-巯基嘧啶盐的配合物[Cu6（pymt）6]并进行结构分析，该配合物能发出强的红色荧光。其中，一价铜离子的配位环境为变形平面三角形，陪体pymt采用μ3-S2N桥联方式参与配位。     

四川马海毛钢花呢的试制

根据四川马海毛原料资源的品质特性，运用精纺粗做的方法，成功地试制出手感滑糯而富有弹性、光泽明亮悦目，各项物理指标符合FZ/T24002-93标准的四川马海毛纯毛钢花呢，达到了马海毛产品的特殊风格。同时指出四川马海毛制成率偏低。